Skip to content
Dugan Design
← All products
+ Add to shopping list
Stains and dyesStain

CPS60

CPS60 Solvent-borne pigment wiping stain, Alder

Ready-mixed solvent-borne pigment wiping stain in an alder shade, part of the CPS51-62 series. Evens out colour variation and hides wood defects, levels well and is lightfast. The dealer lists it for furniture in any species, interior and exterior; the official site files the series under exterior wood. Spray, spray-and-wipe or roller-coat.

  • Staining furniture in any wood species
  • Interior and exterior work
  • Decks, verandas, gazebos, garden furniture, boardwalks, cladding, fences, landscape features (official, for the series via CPS58/CPS62)
  • Alder look on pale, cheaper species (pine, birch, beech)
  • Evening out colour on solid wood and veneer

Mix calculator

g
Thinner750.0 %

When: S10 — fast, for fine-pore wood (alder, beech, birch, maple) and small parts; S12 — medium, for medium-pore wood; S90 — slow, for open-grain wood (oak, ash), big panels and hot shops — more working time for wiping.

Additive

Ratio 100 : 750.0

ComponentWeigh out
CPS60part A58.8 g
S10 / S12 / S90Thinner441 g
Total500 g

Covers roughly 5.56 m² at 90 g/m².

Pot life of the mix: n/a (no hardener).

Ask about CPS60

Answers are based on the CPS60 data and the products it mixes with.

Questions and answers are stored to improve the assistant and prevent abuse; the question text is processed by Anthropic (USA). Privacy policy

Mixing matrix

  • S10 / S12 / S90Thinner
    % by weight: 0–100 %recommended% by volume: 0–100 %recommended

    S10 — fast, for fine-pore wood (alder, beech, birch, maple) and small parts; S12 — medium, for medium-pore wood; S90 — slow, for open-grain wood (oak, ash), big panels and hot shops — more working time for wiping.

    No dilution published for CPS60; 0-100 % is from the dealer table for the ready CPS colour CPS037 (by analogy). Test on an offcut. S10/S12/S90 as stain thinners per the catalog thinner table.

  • S10 / S12 / S90Thinner
    % by weight: 500–1000 %catalog% by volume: 500–1000 %catalog

    S10 — fast, for fine-pore wood (alder, beech, birch, maple) and small parts; S12 — medium, for medium-pore wood; S90 — slow, for open-grain wood (oak, ash), big panels and hot shops — more working time for wiping.

    Catalog figure for the CPS group as a whole, written for the concentrates (CPS1-CPS10); don't let ready-mixed CPS60 down this far — the colour all but disappears.

  • CFS1Additive
    % by weight: 0–400 %recommended% by volume: 0–400 %recommended

    'With the special binder it can be wiped on' — for pore highlighting on open-grain wood.

    CPS60 is already sold as a wiping stain; add binder only after a test panel.

  • CFC3Additive
    % by weight: 200 %schedule

    Finishing flat (anegre veneer) panels under a UV system, 60-80 g/m². The schedule names the CPS series, not a colour; what CFC3 is is not stated in the sources.

  • S90Thinner
    % by weight: 200 %schedule

    Same UV roller schedule.

  • CPS51 / CPS52 / CPS53 / CPS54 / CPS55 / CPS56 / CPS57 / CPS58 / CPS59 / CPS61 / CPS62Additive
    % by weight: any ratio %recommended

    For a custom shade (e.g. alder + tobacco — darker and warmer).

Percentages are per 100 parts of component A.

Characteristics

Components
1K (no hardener)recommended
Carrier
solvent-borne (органоразбавимый, «ОР»)official
Lightfastness
good (светостойкость)dealer
Hiding
hides wood defects, evens out colour (скрывает дефекты)dealer
Levelling
good (хорошая выравнивающая способность)dealer
Pot life
n/a (no hardener)recommended
Gloss
nonerecommended
Drying · Conditions
20 °C
Drying · Full dry (min)
20 minrecommended
Drying · Line flash-off (min)
5 minschedule
Characteristics reference
vocabulary per t-color.ru 'Характеристики'official

Colours

  • CPS60 · alder

Application

HVLP

Consumption
80–100 g/m²dealer
Nozzle
1.2–1.4 (typ. 1.3) mmrecommended
Pressure · air
1.5–2 barrecommended
Spray viscosity
10–16 s DIN4recommended
Wet film
90–115 µmrecommended
Flash-off
20 minrecommended
Sanding between coats
None — never sand the stain itself.recommended

Stir well before and during use — the pigment settles. Alder is a warm, light reddish-brown: on pale fine-pore woods (beech, birch, pine, alder itself) it lays down evenly with S10/S12. To wipe: spray, give it 1-3 min, then wipe along the grain with a sponge or lint-free rag. Go lighter on end grain (it drinks more and goes darker). Always make a test panel on the same species under the same topcoat.

Conventional spray

Nozzle
1.2–1.4 (typ. 1.3) mmrecommended
Pressure · air
2–3 barrecommended
Consumption
80–100 g/m²dealer

More overspray than HVLP: open the fan wide, hold the gun 20-25 cm off.

Airmix (air-assisted airless)

Pressure · fluid
3–6 barrecommended
Pressure · air
1–2 barofficial
Consumption
80–100 g/m²dealer

For production panel/door staining; keep the pot agitated.

Cloth or pad

Wiping with a sponge or soft lint-free rag removes the excess after spraying and evens the tone; on open-grain wood it packs pigment into the pores.

Roller coater (UV)

Flat parts on a roller-coater line only (10-20 g/m² per the dealer).

Panel line schedule

Flash-off
5 minschedule

Flat (anegre veneer) panels under a UV system: stain with CFC3 and S90, 5 min flash at 20-25 °C, then UV filler VTS20011. The schedule does not say how the stain is applied.

Brush

On exterior structures (fences, decks, gazebos) it can be brushed on and wiped back straight away with a rag.

Process and compatibility

Substrate preparation
Dry wood (≤ 12 % MC for furniture, ≤ 15 % outdoors), sand P150-P180 (P150/P180/P220 on the roller line per the schedule), de-dust; take grey weathered wood back to fresh.recommended
Goes under
PTS20 / VTS20011
Sanding
Never sand the stain; first sanding is on the primer (P280-P320).recommended
Temperature and humidity
15-25 °C, RH ≤ 75 % indoors; outdoors 10-25 °C, no direct sun, no rain/dewrecommended
Exterior
Outdoors the stain alone does not protect the wood — always overcoat with a weather-resistant exterior system.recommended

Storage

Packaging
1 л / 5 лdealer

Used in finishing systems

Mixed into

CPS52 / CPS55 / CPS57 / CPS59 / CPS61

Sources

Value tags: “official”, “dealer”, “catalog”, “schedule” are Technocolor data; “workshop” is from our own datasheets; “recommended” is our engineering estimate (hover to see the reasoning).

Not covered by the sources
  • official t-color.ru CPS60 page is an empty stub (name only); properties from dealer + series siblings CPS58/CPS62
  • no 'Все технические характеристики' block on dealer page: solids %, viscosity as supplied, density unknown
  • no thinner/components table on CPS60 dealer page — 0-100 % S10/S12/S90 taken by analogy from dealer CPS037
  • drying times (dust-free/touch/overcoat) not published — 20 min derived by analogy
  • CFS1 binder ratio for a ready CPS colour not published (code + 0-400 % taken from concentrate CPS10 by analogy); CFC3 identity unknown
  • interior vs exterior: official series pages say exterior, dealer says furniture + interior/exterior; recommended exterior topcoat system unknown
  • shelf life
  • storage temperature
  • SDS/hazard data
  • no Technocolor TDS PDF found (web search budget exhausted this session; previous CPS searches found none)
  • official nozzle/pressure not published (derived)