UV-curePutty
VTS20011
VTS20011 clear UV-cure roller filler-primer for parquet (catalog: clear UV filler-sealer for parquet)
Single-component product: no mixing needed — use as supplied (see application below).
Ask about VTS20011
Answers are based on the VTS20011 data and the products it mixes with.
Characteristics
- Solids
- 100catalog
- Pot life
- n/a — one-component UV-cure, no hardener; stable in the trough until it sees UVrecommended
- Drying · Cure
- UV lamp: 1 lamp 80–120 W, belt 10 m/min straight after the filler pass (both schedules use 1 lamp on intermediate coats and 3 lamps only after the last primer/top coat)schedule
- Drying · Flash-off
- none — 100 % solids, nothing to flash. The 5-min drying in the schedules is for the coat underneath: 30–35 °C after VTS20000 (parquet), 20–25 °C after CPS stain (anegri)recommended
- Drying · Conditions
- UV lamp cure; ambient shop temperature (no manufacturer limits; ~18–25 °C assumed)recommended
- Elasticity
- excellent flexibilitycatalog
Colours
- clear · clear
Application
Roller coater (UV)
- Consumption
- 30–35 g/m²official
- Wet film
- 23–32 µmrecommended
- Coats
- 1 roller pass at 30–35 g/m², then UV cure (1 lamp 80–120 W, 10 m/min)schedule
- Recoat
- Right after the UV lamp pass — next coat is UV primer (VTS20015 on parquet, VTS20029 on anegri panels) at 20–25 g/m²schedule
- Sanding between coats
- Not sanded straight after the filler; the whole filler+primer build is belt-sanded P240, P280, P320 after the last primer coat is fully curedschedule
Process and compatibility
- Substrate preparation
- Belt-sand P150, P180, P220; on parquet first roll VTS20000 + CTH 5–10 % at 8–10 g/m² and dry 5 min at 30–35 °C; on anegri veneer stain with CPS 100 / CFC3 200 / S90 200 at 60–80 g/m², dry 5 min at 20–25 °Cschedule
- Sanding
- P240, P280, P320 after the primer build is cured (parquet: after 2nd VTS20002 + 3-lamp cure; anegri: after 2nd VTS20029 + 3-lamp cure)schedule
- Temperature and humidity
- Normal shop conditions (~18–25 °C); keep trough and drums out of daylight/UVrecommended
Storage
Safety: No manufacturer data. UV materials contain acrylate monomers (skin sensitisers): nitrile gloves, goggles, avoid skin contact; shield eyes and skin from the UV lamps.
Used in finishing systems
Sources
Value tags: “official”, “dealer”, “catalog”, “schedule” are Technocolor data; “workshop” is from our own datasheets; “recommended” is our engineering estimate (hover to see the reasoning).
- official product page: properties, roller 30–35 g/m²
- official UV parquet schedule: step 4 VTS20011 30–35 g/m², UV 1 lamp 80–120 W 10 m/min
- official UV anegri flat-panel schedule: step 4 VTS20011 30–35 g/m², same cure
- methods page: roller coating, 98–100 % solids UV, flat parts only
- dealer search — no result
Not covered by the sources
- viscosity (not published anywhere found)
- density
- gloss
- hardness / abrasion
- chemical resistance
- lightfastness / yellowing
- required UV dose (mJ/cm²) / lamp type beyond 80–120 W, 10 m/min
- shelf life, storage temperature, packaging
- safety data sheet
- dealer page: VTS20011 not listed on t-colormarket.ru, lakokraska31.ru or woodonline.ru
- no TDS PDF found (web search budget exhausted, no PDF in local sources)
- nozzle/pressure: not applicable — roller-only material, not sprayable