CTS4
CTS4 solvent-soluble dye toner, brown, for adding to lacquer
Solvent-soluble (ОР) brown dye toner that goes straight into the lacquer. Clear and bright: it doesn't hide the grain, it tints the film and gives the finish more uniform colour and brightness. Compatible with polyurethane, nitrocellulose and acrylic finishes. Dose 0.5–1 % into the lacquer, added just before use; applied by spraying.
- Toning clear PU, acrylic and NC lacquers at 0.5–1 %
- Evening out colour and adding brightness to the finish
- Toning the acrylic topcoat ATL20 + C40 + S80 + CTS 0.5 % over patinated oak (official schedule)
- Toning the PU topcoat PTL61 + C61 + S70 + CTS 0.5 % on veneered worktops (official schedule)
- Colour-matching a stained piece with light passes of tinted lacquer (workshop practice, not from a source)
Ask about CTS4
Answers are based on the CTS4 data and the products it mixes with.
Mixing matrix
- CTS4Additive% by weight: 0.5–1 %dealer
Into PU, acrylic and NC lacquers. Add just before use and stir thoroughly.
Past 1 % the colour muddies fast and swings with film thickness; get the depth from a stain and just fine-tune with CTS.
Open-pore oak kitchen fronts (acrylic): topcoat over CQS patina, 150 g/m², dry 1.5 h at 30–35 °C.
The schedule doesn't name the CTS colour — pick it to suit (brown CTS4 for warm walnut-ish oak).
Beech-veneer worktops (PU; the page heading on the site is a copy-paste of the oak schedule): topcoat over PTS60 + C26 + S50, 150 g/m², dry 1.5 h at 30–35 °C.
Here the base colour comes from CTH water dye + CFH1 + water (80–100 g/m²); CTS in the topcoat evens it out.
| Role | Material | % by weight | % by volume | When |
|---|---|---|---|---|
| Additive | CTS4 | 0.5–1 %dealer | — | Into PU, acrylic and NC lacquers. Add just before use and stir thoroughly.Past 1 % the colour muddies fast and swings with film thickness; get the depth from a stain and just fine-tune with CTS. |
| host_system | ATL20 / AC40 / S80 / CTS4 | — | — | Open-pore oak kitchen fronts (acrylic): topcoat over CQS patina, 150 g/m², dry 1.5 h at 30–35 °C.The schedule doesn't name the CTS colour — pick it to suit (brown CTS4 for warm walnut-ish oak). |
| host_system | PTL61 / C61 / S70 / CTS4 | — | — | Beech-veneer worktops (PU; the page heading on the site is a copy-paste of the oak schedule): topcoat over PTS60 + C26 + S50, 150 g/m², dry 1.5 h at 30–35 °C.Here the base colour comes from CTH water dye + CFH1 + water (80–100 g/m²); CTS in the topcoat evens it out. |
Percentages are per 100 parts of component A.
Characteristics
- Compatibility
- ПУ, НЦ и акриловые ЛКМ (PU, NC and acrylic finishes)dealer
- Dosage %
- 0.5–1 % to lacquerdealer
- Base
- solvent-soluble ('ОР' = органорастворимый) dyedealer
- Transparency
- transparent, bright — no hiding powerdealer
- Lightfastness
- moderate — typical of dyes; less lightfast than pigment stains (CPS/CPH)recommended
- Viscosity
- thin liquid; does not measurably change the host lacquer's viscosity at 0.5–1 %recommended
- Drying · Conditions
- per host lacquer
Colours
- CTS4 · Brown
Application
HVLP
- Nozzle
- 1.3–1.5 (host clear lacquer's tip)recommended
- Pressure · air
- inlet 2.0–2.2 (trigger pulled), cap ≤ 0.7recommended
- Spray viscosity
- host lacquer's working viscosity, ≈18–22 s DIN4 for clear acrylic/PU topcoatsrecommended
- Consumption
- 150 g/m² (tinted lacquer)schedule
- Coats
- 1 tinted coat, normally the last or second-to-last; build colour with extra light passes rather than more dyerecommended
Spray application (dealer). Don't sand through a tinted coat — edges go pale instantly. Keep any denib light (P320–P400), or do the sanding before the tinted coat.
Conventional spray
- Nozzle
- 1.4–1.6recommended
- Pressure · air
- 2.5–3.5 at the gunrecommended
Airmix (air-assisted airless)
- Nozzle
- 0.23–0.28 (009–011 thou), fine-finish tiprecommended
- Pressure · fluid
- 60–100recommended
- Pressure · air
- 0.8–1.5 atomisingrecommended
Process and compatibility
- Substrate preparation
- per host lacquer system; base colour from a stain first (CGS glaze in the oak schedule, CTH water dye in the beech schedule), CTS only to fine-tune in the topcoatschedule
- Goes into
- ATL20, PTL61
- Sanding
- sand the coat before the tinted one; after the tinted coat only light denib P320–P400, never cut throughrecommended
- Temperature and humidity
- as host lacquer; schedule forced dry 30–35 °Cschedule
- Don'ts
- Don't go above 1 % — the colour muddies and swings with film thickness
- Don't add to water-borne lacquers — use the CTH series there
- Don't make up tinted lacquer in advance — add the dye just before use
- Don't spray unevenly: every extra overlap shows as a darker stripe
Storage
- Packaging
- 1 Ldealer
- Shelf life
- check label; typically 12 months in the sealed tinrecommended
- Storage temperature
- +5…+30 °C, sealed, away from heat and flamerecommended
Safety: Not published. Solvent-borne dye — flammable liquid: use in an extracted spray booth, wear an organic-vapour (A2) respirator and nitrile gloves, keep away from flame.
Used in finishing systems
Mixed into
ATL10 SM / ATL20 M / ATL20 SG / ATL20 SM / ATL20 UM / C61 / CTS2 / CTS4 / PTL61
Sources
Value tags: “official”, “dealer”, “catalog”, “schedule” are Technocolor data; “workshop” is from our own datasheets; “recommended” is our engineering estimate (hover to see the reasoning).
- dealer page: properties, use 0.5–1 % in PU/acrylic/NC lacquers, spray, add before use, 1 L pack
- dealer search: CTS1 yellow, CTS2 orange, CTS3 red, CTS4 brown, CTS9 black (all pages live, checked 2026-10-05)
- official schedule: ATL20 100 / C40 20 / S80 30 / CTS 0.5, 150 g/m², 1.5 h @30–35 °C
- official schedule: PTL61 100 / C61 50 / S70 30 / CTS 0.5, 150 g/m², 1.5 h @30–35 °C
- official application methods (spray)
- official CTH4 page: water-based transparent dye (companion series, not for solvent lacquers)
Not covered by the sources
- No official t-color.ru product page and no TDS/SDS found
- Solids, density, solvent type and flash point not published
- Basis of the 0.5–1 % dose (weight vs volume, of lacquer part A vs ready mix) not stated
- Colour code of 'CTS' in the two official schedules not specified
- Lightfastness not published
- Web search budget exhausted — only lakokraska31.ru, woodonline.ru, ndom31.ru checked directly (no listing)
- Shelf life / storage conditions not published (derived values used)
- Dealer 'Все технические характеристики' block absent for CTS4 — no solids/viscosity/density