CPH10
CPH10 water-based pigmented wood stain, white (concentrate)
Water-reducible pigmented wood stain in white, supplied as a concentrate. Evens out colour variation, hides wood defects, levels well and is lightfast. Used for whitewashed/Scandinavian looks on light timbers and to lighten other CPH stains.
- Staining furniture in any timber species
- Whitewash and pastel tones under clear lacquer
- Lightening other CPH stains by intermixing
- Tinting exterior coatings (catalog, CPH series)
Mix calculator
Ratio 100 : 500.0
| Component | Weigh out |
|---|---|
| CPH10part A | 83.3 g |
| waterThinner | 417 g |
| Total | 500 g |
Covers roughly 5.56 m² at 90 g/m².
Ask about CPH10
Answers are based on the CPH10 data and the products it mixes with.
Mixing matrix
- waterThinner% by weight: 400–600 % of concentrateofficial% by volume: 400–600 % of concentrateofficial
Standard dilution for spraying
Clean (ideally demineralised) water. More water = lighter, more translucent tone with more grain showing.
- waterThinner% by weight: 400–1000 % of concentratecatalog
Catalog value for the whole CPH series: up to 1000 % for a light, glaze-like tone
Catalog does not say by weight or volume — for a water system the difference is small.
- CFH1Additive% by weight: 0–200 % of concentrateofficial% by volume: 0–200 % of concentrateofficial
Binder (official site: 0–200 %)
The binder locks the pigment, reduces grain raise and colour rub-off during sanding or the first primer coat.
- CFH1Additive% by weight: 0–400 % of concentratecatalog
2022 catalog for the CPH series: CFH1 up to 400 % (current official page says 0–200 %)
Prefer the current official 0–200 %.
- CFH1Additive% by weight: 15–20 %dealer
Dealer advice: for more even application and less grain raise
Working example (recommendation): 100 g CPH10 + 500 g water + ~100 g CFH1 ≈ 15 % of the ready mix — also within the official 0–200 %.
- CTH / CFH1 / waterAdditive% by weight: 400 % CFH1 per 100 CTH, + water 1000 %schedule
Reference only: CFH1 dosing in an official schedule with the CTH water dye concentrate; not stated for CPH10
Stain dries 20 min at 20–25 °C in this schedule before PTS60 primer.
| Role | Material | % by weight | % by volume | When |
|---|---|---|---|---|
| Thinner | water | 400–600 % of concentrateofficial | 400–600 % of concentrateofficial | Standard dilution for sprayingClean (ideally demineralised) water. More water = lighter, more translucent tone with more grain showing. |
| Thinner | water | 400–1000 % of concentratecatalog | — | Catalog value for the whole CPH series: up to 1000 % for a light, glaze-like toneCatalog does not say by weight or volume — for a water system the difference is small. |
| Additive | CFH1 | 0–200 % of concentrateofficial | 0–200 % of concentrateofficial | Binder (official site: 0–200 %)The binder locks the pigment, reduces grain raise and colour rub-off during sanding or the first primer coat. |
| Additive | CFH1 | 0–400 % of concentratecatalog | — | 2022 catalog for the CPH series: CFH1 up to 400 % (current official page says 0–200 %)Prefer the current official 0–200 %. |
| Additive | CFH1 | 15–20 %dealer | — | Dealer advice: for more even application and less grain raiseWorking example (recommendation): 100 g CPH10 + 500 g water + ~100 g CFH1 ≈ 15 % of the ready mix — also within the official 0–200 %. |
| Additive | CTH / CFH1 / water | 400 % CFH1 per 100 CTH, + water 1000 %schedule | — | Reference only: CFH1 dosing in an official schedule with the CTH water dye concentrate; not stated for CPH10Stain dries 20 min at 20–25 °C in this schedule before PTS60 primer. |
Percentages are per 100 parts of component A.
Characteristics
- Drying · Full cure
- 4 hdealer
- Drying · Before topcoat (h)
- 2–4 hrecommended
- Drying · Conditions
- 20 °C
- Lightfastness
- good lightfastnessofficial
- Hiding
- pigmented, hides defects and colour variationofficial
- Levelling
- good levellingofficial
- Ready-to-use viscosity
- 10–12 s DIN4recommended
- Drying behaviour
- long drying time, sensitive to low temperaturescatalog
Colours
- CPH10 · white
Application
HVLP
- Consumption
- 80–100 g/m²official
- Nozzle
- 1.2–1.4 mmrecommended
- Pressure · air
- 1.5–2 barrecommended
- Spray viscosity
- 10–12 s DIN4recommended
- Coats
- 1–2 coatsrecommended
- Flash-off
- 10–20 minrecommended
- Recoat
- 4 h at 20 °C before primer/lacquerdealer
Stir before and during use — white pigment settles. Strain through 125–190 µm. 15–20 cm distance, 50 % overlap, even wet coat without puddles; go lighter on end grain. (Recommendation.)
Conventional spray
- Consumption
- 80–100 g/m²official
- Nozzle
- 1.2–1.4 mmrecommended
- Pressure · air
- 2–3 barrecommended
- Spray viscosity
- 10–12 s DIN4recommended
Same routine as HVLP; lower transfer (up to 40 %, methods page).
Airmix (air-assisted airless)
- Consumption
- 80–100 g/m²official
- Nozzle
- 0.18–0.23 mm (0.007–0.009 in tip)recommended
- Pressure · fluid
- 8–15 barrecommended
- Pressure · air
- 1–2 barofficial
Production only; keep the pot agitated (pigment settles).
Cloth or pad
- Consumption
- 80–100 g/m²catalog
Spray then immediately wipe along the grain with a pad — stain stays in the pores, giving a pickled/whitewashed look on oak/ash.
Roller
- Consumption
- 10–20 g/m²catalog
Flat parts on a roller line only.
Process and compatibility
- Substrate preparation · Sanding
- P150, P180 (hand sanding)dealer
- Substrate preparation · Grain raise
- Pre-wet with water, dry, light sand to remove raised fibres before water stainsofficial
- Goes over
- bare sanded wood
- Goes under
- HTL20 SM
- Sanding
- Don't sand the stain itself — sand the first primer coat (P280–P320 per dealer schedule); white pigment rubs through to bare wood on edges easily.recommended
- Temperature and humidity
- 15–25 °C, RH 50–70 %, not below +10 °Crecommended
- Don'ts
- Do not let it freeze
- Do not flood it on — pores go chalky and blotchy
- Do not overcoat before fully dry (4 h at 20 °C)
- Do not reduce with solvents — water only
Storage
- Packaging
- 1 kg,5 kgdealer
- Storage temperature
- 5–30 °Crecommended
Safety: Water-based. Wear gloves and a spray mask/respirator for aerosols; do not pour down the drain. (No SDS found.)
Mixed into
CFH1 / CPH21 / CPH21/1 / CPH22 / CPH22/1 / CPH23 / CPH23/1 / CPH25 / CPH25/1 / CPH26 / CPH26/1 / CPH3 / CPH6 / CPH60 / CPH600 / CPH610 / CPH623
Sources
Value tags: “official”, “dealer”, “catalog”, “schedule” are Technocolor data; “workshop” is from our own datasheets; “recommended” is our engineering estimate (hover to see the reasoning).
- official page: properties, spray 80–100 g/m², water 400–600 %, CFH1 0–200 %
- dealer page: application area, CFH1 15–20 %, full dry 4 h, schedule under HTL20 SM, packaging 1/5 kg (the old .../krasiteli_morilki_vodorazbavimye/cph10/ path now redirects to the catalog root)
- catalog 2025 p.5 (transcript catalog-2025-p01-05.md (Katalog-Technocolor-2025-2026, стр. 5)): CPH series water 400–1000 %, spray/spray+wipe 80–100 g/m², roller 10–20 g/m², usable for tinting exterior coatings
- official CPH line listing (intermixable codes)
- official schedule 'Отделка столешниц, облицованных шпоном бука (ПУ)': CTH 100 : CFH1 400 : water 1000, 80–100 g/m², dry 20 min at 20–25 °C, then PTS60 primer
- application methods page
- grain raising before water stains
- 2022 catalog p.4: CPH series water 400–600 %, binder CFH1 0–400 %, spray 80–100 g/m²; «продолжительная сушка и чувствительность к низким температурам»; CPH base colours CPH1/3/9/10, ready colours CPH21–26
Not covered by the sources
- Solids content of the concentrate (not published by official site, dealer or catalog)
- Viscosity of the concentrate and density
- Dust-free / touch-dry times (only 4 h full dry given by dealer)
- Shelf life and official storage temperature
- Basis of the dealer's CFH1 15–20 % (of concentrate or of ready mix) — official page gives 0–200 % of concentrate
- CFH1 binder has no official or dealer product page (no own characteristics)
- No Technocolor TDS/SDS PDF found for CPH10
- Not used in any official finishing schedule (information/technology); the only CFH1 schedule uses CTH concentrate dye