CPH600
CPH600 clear waterborne wood glaze (tinting base)
Clear waterborne glaze with wax, sold as the base (binder) for tinting glazes. It protects wood against the weather and UV, leaves a water-repellent (hydrophobic) film and does not fade. It contains no biocides, so it is fine indoors. Outdoors, put a protective impregnation down first.
- Garden furniture
- Gazebos and pergolas
- Wooden items used indoors and outdoors
- Base for custom glaze colours tinted with CPH1/3/9/10 concentrates
Mix calculator
Ratio 100 : 0.0
| Component | Weigh out |
|---|---|
| CPH600part A | 500 g |
| waterThinner | 0.0 g |
| Total | 500 g |
Covers roughly 7.14 m² at 70 g/m².
Ask about CPH600
Answers are based on the CPH600 data and the products it mixes with.
Mixing matrix
- % by weight: 1–10 %dealer% by volume: 1–10 %recommended
Making a custom glaze colour: tint with the base pigment concentrates CPH1 (yellow), CPH3 (red), CPH9 (black) and CPH10 (white) at 1–10 %, depending on the shade you want.
The dealer's note has a typo, 'CFH6'; from context it means CPH600. Always check the colour on a sample board of the same species.
- waterThinner% by weight: 0–10 %recommended% by volume: 0–10 %recommended
Only if the glaze drags under the brush in hot weather. Normally applied as supplied.
| Role | Material | % by weight | % by volume | When |
|---|---|---|---|---|
| Additive | CPH1 / CPH3 / CPH9 / CPH10 | 1–10 %dealer | 1–10 %recommended | Making a custom glaze colour: tint with the base pigment concentrates CPH1 (yellow), CPH3 (red), CPH9 (black) and CPH10 (white) at 1–10 %, depending on the shade you want.The dealer's note has a typo, 'CFH6'; from context it means CPH600. Always check the colour on a sample board of the same species. |
| Thinner | water | 0–10 %recommended | 0–10 %recommended | Only if the glaze drags under the brush in hot weather. Normally applied as supplied. |
Percentages are per 100 parts of component A.
Characteristics
- Hydrophobic
- yesofficial
- UV protection
- reliable UV protection, non-fadingcatalog
- Biocide-free
- yescatalog
- Lightfastness
- does not fadedealer
- Binder type
- waterborneofficial
- Components
- 1K (single-component, no hardener)recommended
- Drying · Conditions
- 20 °C, 60 % RH (assumed standard conditions)
Colours
- CPH600 · clear / colourless
Application
Brush
- Consumption
- 60–80 g/m²official
- Sanding between coats
- optional light denib P240–P320 after the first coat if the grain is raised; dust off and do not cut through the colourrecommended
Brush along the grain in thin, even coats with no puddles. Stir before use, because the wax and the tint settle. Outdoors, impregnate first. Brushing is the only officially listed method.
HVLP
NOT listed by the manufacturer. If you do spray it, lay it on thin and immediately brush it out along the grain to work it into the pores. Use spray gear rated for waterborne (stainless).
Process and compatibility
- Substrate preparation
- Dry, clean, dust-free wood. Outdoors, treat with a protective impregnation first (the catalog says CPH6; the dealer says CTH100).catalog
- Goes over
- CPH6 / CTH100
- Don'ts
- Do not use outdoors without a protective impregnation first, because the glaze has no biocides
- Do not thin by 400–1000 % like the CPH pigment stains; that rate is for the concentrates, not the glaze
- Do not apply below +10 °C, in rain or on wet wood
Storage
- Packaging
- 1 kg,5 kg,10 kgdealer
- Storage temperature
- +5…+30 °C, protect from frostrecommended
Safety: Waterborne and biocide-free, so it is approved for indoor use (catalog). No safety data sheet was found. Wear gloves and keep the room ventilated.
Sources
Value tags: “official”, “dealer”, “catalog”, “schedule” are Technocolor data; “workshop” is from our own datasheets; “recommended” is our engineering estimate (hover to see the reasoning).
- official page: properties (binder for tinting, hydrophobic), brush 60–80 g/m²
- dealer: description, wax, biocide-free, uses, 1–2 coats, tint with CPH1/3/9/10 at 1–10 %, packaging, price; no technical-characteristics block
- methods page: brushing for small surfaces and restoration work
- official sister-glaze page: contains wax, used as finish coat without subsequent lacquer
- official CPH6 colourless impregnation (anti-fungal/mould/insect) — the pre-treatment named by the catalog
Not covered by the sources
- solids % (part A)
- viscosity
- density
- pot life (N/A, 1K, but not stated)
- drying times (dust-free/touch/full): none published
- gloss level
- official spray parameters: only brush is listed
- whether tint % is by weight or by volume
- overcoatability with lacquer
- shelf life
- technical data sheet (ТДС) PDF: none found online
- the dealer (CTH100) and the catalog (CPH6) disagree on which pre-treatment impregnation to use
- not used in any official finishing schedule (information/technology)