CPH622
CPH622 Water-based wax wood glaze (azure), light walnut
Water-based wax glaze pigmented in a light-walnut shade. Colours evenly without blotching, levels the tone well and is lightfast — it shields the wood from UV and does not fade. Contains wax and is meant as a finish coat with no lacquer on top. Biocide-free, so it can also be used indoors; outdoors, treat the wood first with a protective impregnation (dealer and 2022 catalog: CTH100; 2025–2026 catalog: CPH6).
- Colouring and protecting exterior timber: gazebos, fences, garden furniture
- Window frames, balconies, cladding on timber houses (over CTH100/CPH6 protective impregnation)
- Interior woodwork too (biocide-free)
Single-component product: no mixing needed — use as supplied (see application below).
Ask about CPH622
Answers are based on the CPH622 data and the products it mixes with.
Mixing matrix
- waterThinner
Only if the can has thickened or in hot weather; normally used neat.
Never thin with solvent thinners (S50/S80 etc.) — it is water-borne.
- CPH600Additive
To make the shade lighter / more transparent.
Always test on the same species. For custom colours the official route is tinting CPH600 with CPH 1, 3, 9, 10 concentrates (1–10 %).
| Role | Material | % by weight | % by volume | When |
|---|---|---|---|---|
| Thinner | water | — | — | Only if the can has thickened or in hot weather; normally used neat.Never thin with solvent thinners (S50/S80 etc.) — it is water-borne. |
| Additive | CPH600 | — | — | To make the shade lighter / more transparent.Always test on the same species. For custom colours the official route is tinting CPH600 with CPH 1, 3, 9, 10 concentrates (1–10 %). |
Percentages are per 100 parts of component A.
Characteristics
- Binder
- water-borne, wax-modified (ВР лазурь с воском)official
- Lightfastness
- good — UV protection, does not fade (светостойкая, не выгорает)dealer
- Levelling
- good levelling, even colour, no blotchingofficial
- Biocides
- none (не содержит биоцидов)dealer
- Water repellency
- hydrophobic film (base CPH600: «создаёт гидрофобное покрытие»)official
- Drying · Full cure
- 4 hdealer
- Drying · Conditions
- 20 °C
- Viscosity
- ready to use, low (brushable liquid, roughly 15–25 s DIN4)recommended
Colours
- CPH622 · light walnut
Application
Brush
- Sanding between coats
- normally none; if fibres raise after coat 1, a light scuff with a P220–P240 pad or fine abrasive sponge, dust offrecommended
Brush along the grain, working it well in, no runs or puddles; pay special attention to end grain. Stir before use — the pigment settles.
HVLP
Not an official method. If you spray, back-brush along the grain straight away, otherwise the wax and pigment just sit on top and the exterior finish won't last as long. Clean the gun with water.
Process and compatibility
- Substrate preparation
- Dry, clean wood with no old film finishes, resin or dust. Outdoors, apply a protective impregnation first (CTH100 per dealer/2022 catalog, or CPH6 per 2025–2026 catalog) and let it dry.
- Goes over
- CTH100 / CPH6
- Don'ts
- Don't lacquer over it — it's a wax-containing finish coat and lacquer adheres poorly to wax
- Don't thin with solvent thinners
- Don't apply on wet or frozen timber
- Don't use outdoors without a protective impregnation underneath (CTH100 / CPH6) — the glaze contains no biocides
Storage
- Packaging
- 1 kg,5 kgdealer
- Storage temperature
- +5…+30 °C, protect from frostrecommended
Safety: Water-borne, biocide-free. Wear gloves, and a respirator if spraying; clean tools with water. No official SDS for CPH622 was found.
Mixed into
Sources
Value tags: “official”, “dealer”, “catalog”, “schedule” are Technocolor data; “workshop” is from our own datasheets; “recommended” is our engineering estimate (hover to see the reasoning).
- official page: properties, brush 60–80 g/m²
- dealer: description, application area, 1–2 coats, full dry 4 h at 20 °C, CTH100 pre-treatment, packaging 1/5 kg, price
- Technocolor catalog 2022: exterior section, CPH lazur text (pre-treatment CTH100), 60–80 g/m², colour list
- CPH600 clear base: tinting with CPH1/3/9/10 1–10 %
- official wood prep: impregnation when exposed to moisture
- official application methods (brush)
- official CPH6 impregnation page: spray/dip/brush 60–80 g/m²
Not covered by the sources
- solids content (не опубликован)
- viscosity (measured)
- density
- gloss value
- shelf life
- official thinning ratio
- official spray parameters (only brush is listed)
- touch-dry time (only full dry 4 h published)
- recoat interval (official)
- no technical data sheet (ТДС) or SDS found online
- not used in any official finishing schedule (information/technology)
- pre-treatment code conflict: dealer + 2022 catalog say CTH100, 2025–2026 catalog says CPH6 — both listed