CPH1
CPH1 Water-based pigment stain concentrate, yellow
Concentrated water-borne pigment stain. Diluted with water it makes a stain for any wood species; it can also be used to tint exterior impregnations. Pigment-based: evens out colour variation, hides wood defects, levels well and is lightfast.
- Staining furniture in any wood species
- Mixing custom stain shades with other CPH colours
- Tinting coloured impregnations and exterior coatings
Mix calculator
Ratio 100 : 500.0
| Component | Weigh out |
|---|---|
| CPH1part A | 83.3 g |
| WATERThinner | 417 g |
| Total | 500 g |
Covers roughly 5.56 m² at 90 g/m².
Ask about CPH1
Answers are based on the CPH1 data and the products it mixes with.
Mixing matrix
- WATERThinner% by weight: 400–600 % of concentrateofficial% by volume: 400–600 % of concentrateofficial
Standard working stain for spraying.
More water = lighter, more transparent tone; less = denser, more hiding. Dealer gives the same formula: CPH1 100 % + water 400–600 %.
- WATERThinner% by weight: 400–1000 % of concentratecatalog
The catalogue allows heavier dilution, up to 1000 %, for very pale tones.
Catalogue gives just '%' without weight/volume; for water and a water-based concentrate the difference is negligible.
- CFH1Additive% by weight: 0–200 % of concentrateofficial% by volume: 0–200 % of concentrateofficial
Water-based spray binder (official 0–200 % of concentrate). Purpose per the dealer: more even lay-down and less grain raising.
0 % is allowed (no binder).
- CFH1Additive% by weight: 10–20 % of ready-to-use staindealer
For better levelling and less raised grain.
Dealer states both 15–20 % and 10–20 % of the ready stain. Converted: at 500 % water, 10–20 % of ready stain ≈ 60–120 % of concentrate — within the official 0–200 %.
| Role | Material | % by weight | % by volume | When |
|---|---|---|---|---|
| Thinner | WATER | 400–600 % of concentrateofficial | 400–600 % of concentrateofficial | Standard working stain for spraying.More water = lighter, more transparent tone; less = denser, more hiding. Dealer gives the same formula: CPH1 100 % + water 400–600 %. |
| Thinner | WATER | 400–1000 % of concentratecatalog | — | The catalogue allows heavier dilution, up to 1000 %, for very pale tones.Catalogue gives just '%' without weight/volume; for water and a water-based concentrate the difference is negligible. |
| Additive | CFH1 | 0–200 % of concentrateofficial | 0–200 % of concentrateofficial | Water-based spray binder (official 0–200 % of concentrate). Purpose per the dealer: more even lay-down and less grain raising.0 % is allowed (no binder). |
| Additive | CFH1 | 10–20 % of ready-to-use staindealer | — | For better levelling and less raised grain.Dealer states both 15–20 % and 10–20 % of the ready stain. Converted: at 500 % water, 10–20 % of ready stain ≈ 60–120 % of concentrate — within the official 0–200 %. |
Percentages are per 100 parts of component A.
Characteristics
- Lightfastness
- good (светостойкий)official
- Levelling
- good levelling / evens colour variationofficial
- Drying · Full cure
- 4 hdealer
- Drying · Conditions
- 20 °C
- Drying · Touch-dry
- 20–30 min (at working dilution, 80–100 g/m², 20–25 °C)recommended
- Thinner is water
- yesofficial
Colours
- CPH1 · yellow
Application
HVLP
- Consumption
- 80–100 g/m2official
- Coats
- 1 even wet coat; a 2nd light mist only to correct tonerecommended
- Nozzle
- 1.0–1.3 mm (1.2 mm typical); 1.4 mm acceptablerecommended
- Pressure · air
- inlet 1.5–2.0 bar with trigger pulled (cap ≈0.5–0.7 bar)recommended
- Pressure · fluid
- gravity cup; fluid knob ~1–1.5 turnsrecommended
- Spray viscosity
- as diluted — water-thin, ≈10–12 s DIN4 (below the cup's valid range); no adjustmentrecommended
- Flash-off
- 10–20 min before handlingrecommended
- Recoat
- 4 h before primerdealer
- Sanding between coats
- Do not sand the stain itself; denib only after the first primer coatrecommended
(Derived guidance.) 1.2 mm tip, 1.5–2 bar inlet, 15–20 cm distance, 50 % overlap. Lay one even wet coat without puddles; go lighter on verticals to avoid runs. Stir the stain now and then — pigment settles.
Conventional spray
- Consumption
- 80–100 g/m2official
- Nozzle
- 1.0–1.2 mmrecommended
- Pressure · air
- 2.0–3.0 barrecommended
As HVLP but more overspray — use extraction.
Airmix (air-assisted airless)
- Consumption
- 80–100 g/m2official
- Nozzle
- tip 0.007–0.009 in (0.18–0.23 mm), fan 20–40°recommended
- Pressure · fluid
- 8–15 barrecommended
- Pressure · air
- 1–1.5 barrecommended
For production runs; always do a test panel.
Cloth or pad
- Consumption
- 80–100 g/m2catalog
Spray, then wipe along the grain with a pad/cloth until the tone is even — take off the excess or the pigment will blotch.
Roller
- Consumption
- 10–20 g/m2catalog
Roller-coater application on flat panels (catalogue: 'roller application'; not a UV material).
Process and compatibility
- Substrate preparation
- Sand P150–P220 (edges/solid K80–K120), de-dust. On solid wood and veneer pre-wet with water, dry and knock back the raised grain with P220 before staining.recommended
- Sanding
- Don't sand the stain. After the first primer coat sand P240–P320 lightly, without cutting through on edges.recommended
- Temperature and humidity
- 15–25 °C, RH 50–70 %; don't work below 10 °C.recommended
- Don'ts
- Don't prime before 4 h
- Don't over-apply — blotches and runs
- Don't let it freeze
- Don't sand the stain layer
Storage
- Packaging
- 1 kg,5 kgdealer
- Storage temperature
- +5…+30 °C, protect from frostrecommended
Safety: Water-borne, solvent-free. Wear gloves; respirator and extraction when spraying; it stains skin.
Mixed into
CFH1 / CPH21 / CPH21/1 / CPH22 / CPH22/1 / CPH23 / CPH23/1 / CPH25 / CPH25/1 / CPH26 / CPH26/1 / CPH3 / CPH6 / CPH60 / CPH600 / CPH610 / CPH623
Sources
Value tags: “official”, “dealer”, “catalog”, “schedule” are Technocolor data; “workshop” is from our own datasheets; “recommended” is our engineering estimate (hover to see the reasoning).
- properties, spray 80–100 g/m², water 400–600 % w/v, CFH1 0–200 % w/v
- description, use, intermixing, CFH1 10–20 / 15–20 % of ready stain, full dry 4 h, 4 h before primer, packaging 1/5 kg, price 3145 ₽/kg (2026-10-05)
- official analogue schedule with CFH1 water-dye system
- application method parameters (pneumatic transfer ≤40 %, airmix fluid ≤20 bar, assist air 1–2 bar)
- official analogue schedule: CTH+CFH2 water dye, 30 min, then PTS50
Not covered by the sources
- solids_pct
- density
- viscosity of concentrate
- pot life (n/a — single-pack, no reaction)
- dust-free / touch time (only derived)
- shelf life
- storage temperature (only derived)
- no technical data sheet (ТДС) PDF or SDS found
- no official finishing schedule uses CPH1
- exact compatibility list with topcoats is not stated by Technocolor