CPH25/1
CPH25 waterborne pigment stain, mahogany (/1 variant)
Waterborne pigment stain in mahogany. Evens out colour variation and hides wood defects, levels the tone well, good lightfastness. Supplied as a concentrate reduced with water; CFH1 binder is already partly included.
- colouring furniture in any wood species
- evening out mismatched timber (beech, birch, finger-jointed panels, veneer)
- tinting exterior coatings (per catalog)
Mix calculator
Ratio 100 : 500.0
| Component | Weigh out |
|---|---|
| CPH25/1part A | 83.3 g |
| waterThinner | 417 g |
| Total | 500 g |
Covers roughly 5.56 m² at 90 g/m².
Pot life of the mix: n/a (1K).
Ask about CPH25/1
Answers are based on the CPH25/1 data and the products it mixes with.
Mixing matrix
- waterThinner% by weight: 400–600 %official% by volume: 400–600 %official
Standard reduction per the manufacturer's site: 4–6 parts water to 1 part stain.
More water = lighter, more transparent tone. Use clean soft (filtered/distilled) water at room temperature.
- waterThinner% by weight: 400–1000 %catalog
The 2025–2026 catalog states 'Water 400–1000 %' for the series without explanation. The high end (our interpretation) suits pale, see-through tones and roller application.
The catalog gives one range for the whole CPH series: 'Water 400–1000 %'.
- CFH1Additive% by weight: 0–200 %official% by volume: 0–200 %official
CFH1 binder is added for more even laydown and less grain raising, especially at high water reductions.
Per the dealer the stain already contains ~15–20 % CFH1, so extra binder is optional (hence the 0 % lower limit).
- CFH1Additive% by weight: 0–400 %catalog
The 2022 catalog allowed up to 400 % CFH1 (matches the CFH1 400 % ratio in the official schedule for CTH dyes).
Older catalog; the current product page says 0–200 %. Work to 0–200 %.
- CFH1Additive% by weight: 15–20 %dealer
Already added at the factory.
'For more even application and reduced grain raising, CFH1 binder (15–20 %) has been added to the stain.'
- % by weight: 0–100 %dealer
Colour matching: all CPH stains intermix in any ratio (bases CPH1 yellow, CPH3 red, CPH9 black, CPH10 white).
Blend the concentrates before adding water; always do a test panel on the same species.
| Role | Material | % by weight | % by volume | When |
|---|---|---|---|---|
| Thinner | water | 400–600 %official | 400–600 %official | Standard reduction per the manufacturer's site: 4–6 parts water to 1 part stain.More water = lighter, more transparent tone. Use clean soft (filtered/distilled) water at room temperature. |
| Thinner | water | 400–1000 %catalog | — | The 2025–2026 catalog states 'Water 400–1000 %' for the series without explanation. The high end (our interpretation) suits pale, see-through tones and roller application.The catalog gives one range for the whole CPH series: 'Water 400–1000 %'. |
| Additive | CFH1 | 0–200 %official | 0–200 %official | CFH1 binder is added for more even laydown and less grain raising, especially at high water reductions.Per the dealer the stain already contains ~15–20 % CFH1, so extra binder is optional (hence the 0 % lower limit). |
| Additive | CFH1 | 0–400 %catalog | — | The 2022 catalog allowed up to 400 % CFH1 (matches the CFH1 400 % ratio in the official schedule for CTH dyes).Older catalog; the current product page says 0–200 %. Work to 0–200 %. |
| Additive | CFH1 | 15–20 %dealer | — | Already added at the factory.'For more even application and reduced grain raising, CFH1 binder (15–20 %) has been added to the stain.' |
| Additive | CPH1 / CPH3 / CPH9 / CPH10 / CPH21 / CPH22 / CPH23 / CPH24 / CPH26 | 0–100 %dealer | — | Colour matching: all CPH stains intermix in any ratio (bases CPH1 yellow, CPH3 red, CPH9 black, CPH10 white).Blend the concentrates before adding water; always do a test panel on the same species. |
Percentages are per 100 parts of component A.
Characteristics
- Components
- 1K concentrate; reduced with waterrecommended
- Carrier
- waterofficial
- Pot life
- n/a (1K)recommended
- Lightfastness
- good lightfastnessdealer
- Hiding
- high hiding; masks wood defectscatalog
- Drying · Conditions
- 20 °C
- Drying · Full cure
- 4 hdealer
- Drying · Overcoat (h)
- 4 hdealer
- Thixotropy
- norecommended
- Viscosity
- water-like once reduced (~11–13 s DIN4) srecommended
Colours
- CPH25 · mahogany
Application
HVLP
- Consumption
- 80–100 g/m²official
- Nozzle
- 1.2–1.4 (typ. 1.3) mmrecommended
- Pressure · air
- 1.5–2 barrecommended
- Spray viscosity
- 11–13 s DIN4recommended
- Coats
- 1–2 coatsrecommended
- Recoat
- 4 h at 20 °Cdealer
- Sanding between coats
- Don't sand the stain itself — it cuts through to bare wood easily. Knock the raised grain down after the first primer coat (P280–P320).recommended
Lay one even wet coat, 50 % overlap, gun 15–20 cm off; don't flood verticals — stain runs leave dark streaks.
Conventional spray
- Consumption
- 80–100 g/m²official
- Nozzle
- 1.2–1.4 (typ. 1.3) mmrecommended
- Pressure · air
- 2–3 barrecommended
Methods page: air spray is the universal method, transfer efficiency up to 40 %.
Airmix (air-assisted airless)
- Consumption
- 80–100 g/m²official
- Nozzle
- 0.18–0.23 mmrecommended
- Pressure · fluid
- 10–20 barrecommended
- Pressure · air
- 1–2 barofficial
Good for production panels/fronts: even tone, less fog.
Cloth or pad
- Consumption
- 80–100 g/m²catalog
- Flash-off
- 0–3 minrecommended
Spray then wipe (2025–2026 catalog): spray on and immediately rub in with a sponge/rag or brushes to even the tone and bring out the grain.
Roller
- Consumption
- 10–20 g/m²catalog
Roller-coater for flat panels/flooring, 10–20 g/m² (2025–2026 catalog). The catalog gives 400–1000 % water for the series; tying the high end to roller use is our reading, not stated.
Airless
- Nozzle
- not recommendedrecommended
Not recommended for stain: delivers far too much material, uneven colour.
Process and compatibility
- Substrate preparation
- Sand P150, P180; de-dust. Advisable: pre-raise the grain (damp sponge), dry, and denib P180–P220.dealer
- Sequence
- [object Object],[object Object],[object Object],[object Object],[object Object],[object Object],[object Object],[object Object]dealer
- Goes under
- HTL20 SM
- Goes under (derived)
- PTS50,PTS60,ATS20recommended
- Sanding
- Never sand the stain; knock down raised grain on the first primer coat, P280–P320.recommended
- Temperature and humidity
- Apply and dry at 18–25 °C, RH ≤ 70 %; not below 15 °C. Keep from freezing.recommended
- Don'ts
- don't flood it — runs and blotches
- don't sand the stain coat
- don't topcoat with 2K primer before the stain is fully dry
- don't thin with solvent — water only
- don't let it freeze
Storage
- Packaging
- 1 kg,5 kg,25 kgdealer
- Storage temperature
- +5…+30 °C, protect from frostrecommended
- Shelf life
- unknown — typically 12 months unopenedrecommended
Safety: Waterborne, thinned with water. When spraying wear a particulate respirator (P2), gloves and glasses; ventilate. Don't pour leftovers down the drain.
Mixed into
Sources
Value tags: “official”, “dealer”, “catalog”, “schedule” are Technocolor data; “workshop” is from our own datasheets; “recommended” is our engineering estimate (hover to see the reasoning).
- dealer product page: properties, use, rate, CPH intermix + CFH1 15–20 % note, finishing instruction with HTL20 SM
- 2022 catalog: CPH* water 400–600 %, CFH1 0–400 %, long drying, sensitive to low temperature; colour list
- application methods page
Not covered by the sources
- solids content
- density
- viscosity of the concentrate (as supplied)
- dust-free / touch dry times
- shelf life & storage temperature (official)
- SDS / safety data
- no official finishing schedule uses CPH codes
- no real ТДС (technical data sheet) PDF found online
- CFH1 binder has no official product page in the local sources
- meaning of the '/1' suffix (dealer price ~half of CPH25 — possibly a pre-diluted or alternate-batch version; not stated)
- whether CPH25/1 takes the same 400–600 % water reduction as CPH25
- CPH25/1 has no official t-color.ru page; mix/application copied from the series data (official CPH25 page + catalog)