CPH610
CPH610 White wood glaze (water-based, wax-modified)
White pigmented water-based wood glaze with added wax. Colours evenly without blotching, levels well and is lightfast; per the dealer and catalog it gives reliable UV protection and does not fade. Used as the final finish — no lacquer goes on top. Contains no biocides, so it can also be used indoors; for exterior work, pre-treat the timber with a protective impregnation first (the dealer names CTH100, the 2025–2026 catalog names CPH6).
- gazebos, fences and other exterior timber structures
- interior woodwork (biocide-free — per dealer/catalog description)
Mix calculator
Ratio 100 : 0.0
| Component | Weigh out |
|---|---|
| CPH610part A | 500 g |
| waterThinner | 0.0 g |
| Total | 500 g |
Covers roughly 7.14 m² at 70 g/m².
Ask about CPH610
Answers are based on the CPH610 data and the products it mixes with.
Mixing matrix
- % by weight: 1–5 %dealer
To make a custom shade: tint with the CPH base concentrates CPH1 (yellow), CPH3 (red), CPH9 (black), CPH10 (white).
1–5 % for the white glaze (the dealer gives 1–10 % for the colourless CPH600). Stir the tint in thoroughly and do a test panel on the same species.
- waterThinner% by weight: 0–5 %recommended
Only if needed: hot weather, very thirsty timber, spraying.
Never thin with S50/S80 or any solvent thinner.
| Role | Material | % by weight | % by volume | When |
|---|---|---|---|---|
| Additive | CPH1 / CPH3 / CPH9 / CPH10 | 1–5 %dealer | — | To make a custom shade: tint with the CPH base concentrates CPH1 (yellow), CPH3 (red), CPH9 (black), CPH10 (white).1–5 % for the white glaze (the dealer gives 1–10 % for the colourless CPH600). Stir the tint in thoroughly and do a test panel on the same species. |
| Thinner | water | 0–5 %recommended | — | Only if needed: hot weather, very thirsty timber, spraying.Never thin with S50/S80 or any solvent thinner. |
Percentages are per 100 parts of component A.
Characteristics
- Drying · Full cure
- 4 hdealer
- Drying · Conditions
- 20 °C
- Lightfastness
- good lightfastness (official: «светостойкость»); dealer and catalogs add: reliable protection from UV, does not fadeofficial
- Levelling
- good levelling, even colour, no blotchingofficial
- Biocides
- none (not an antiseptic — use CTH100 / CPH6-series impregnation underneath outdoors)dealer
- Hydrophobic
- water-repellent coating (stated for the CPH600 binder of the same series)official
- Components
- 1K, ready to userecommended
Colours
- CPH610 · white
Application
Brush
- Consumption
- 60–80 g/m² per coatofficial
- Coats
- 1–2dealer
- Sanding between coats
- optional light denib P220–P320 only if raised grain; do not cut through the colourrecommended
Stir well before use (pigment settles). Apply with a wide brush along the grain, thin and even, no runs; work edges and end grain carefully.
HVLP
- Spray viscosity
- use as supplied; if needed add ≤ 5 % waterrecommended
- Consumption
- 60–80 g/m² per coatofficial
- Coats
- 1–2dealer
Not an official method. Spray thin; on open-grained or exterior timber, back-brush along the grain straight away so the glaze gets into the wood and doesn't streak.
Process and compatibility
- Substrate preparation
- Dry (MC ≤ 12–15 %), clean, dust-free bare timber with no old film coatings. Sand P120–P180. For exterior use, pre-treat with a protective impregnation first: CTH100 preservative (dealer) or CPH6 (2025–2026 catalog).dealer
- Goes over
- CTH100 / CPH6
- Don'ts
- don't topcoat with lacquer — it's the finish (the wax will hurt lacquer adhesion)
- don't thin with solvents
- don't apply on wet timber, in rain, in direct hot sun or below 10 °C
- don't rely on it as a preservative — no biocides; use an impregnation outdoors
Storage
- Packaging
- 1,5 kgdealer
- Storage temperature
- +5…+30 °C, protect from frostrecommended
Safety: Water-based, biocide-free (allowed indoors). Wear gloves; use a particulate mask when spraying. Don't pour leftovers down the drain.
Mixed into
Sources
Value tags: “official”, “dealer”, “catalog”, “schedule” are Technocolor data; “workshop” is from our own datasheets; “recommended” is our engineering estimate (hover to see the reasoning).
- official page: properties, wax, finish without lacquer, brush 60–80 g/m²
- dealer: description, uses, CTH100 pre-treat, tint CPH1/3/9/10 1–5 %, 1–2 coats, full dry 4 h @20 °C, packs 1/5 kg, price
- third-party listing: brand/model, HS code 3209100000 (water-borne acrylic/vinyl)
- application methods page (brush for small areas/restoration; dip/flow used for impregnation-stains)
Not covered by the sources
- solids %
- viscosity (DIN4 / VZ-4)
- density
- gloss units
- touch-dry / dust-free time (only full dry 4 h is published)
- recoat interval
- shelf life
- storage temperature
- official spray/dip parameters (only brush is official)
- temperature/RH limits
- safety data sheet
- no Technocolor TDS PDF found online
- not used in any official finishing schedule