Skip to content
Dugan Design
← All products
+ Add to shopping list
Patinas and glazesGlaze

CQS10049

CQS10049 White patina

White patina under a separate code (dealer only, no official page). Properties, use and thinners (S10/S2000 100–200 %) match CQS10; the dealer additionally lists 17 s ВЗ-4 viscosity and 12-month shelf life. Also sold in 25 kg; dealer price 851 vs 3650 RUB/kg for CQS10 — possibly an industrial or tinted-to-order version, the maker doesn't say.

  • Decapé / limed effect on open-pore oak and ash (white in the pores)
  • Ageing (distressed) effect on interior furniture and woodwork
  • Glazing raised-panel and routed fronts over enamel
  • Patina on PU-foam (PPU) mouldings, frames and decor
  • Special effects: 'blur', stone, metallic enamel with patina

Mix calculator

g
Thinner150.0 %

When: Default: fastest drying and a harder film; patina wipes back harder — for crisp, high-contrast results.

Ratio 100 : 150.0

ComponentWeigh out
CQS10049part A200 g
S10Thinner300 g
Total500 g

Covers roughly 5.56 m² at 90 g/m².

Pot life of the mix: n/a — one-component, no hardener.

Ask about CQS10049

Answers are based on the CQS10049 data and the products it mixes with.

Questions and answers are stored to improve the assistant and prevent abuse; the question text is processed by Anthropic (USA). Privacy policy

Mixing matrix

  • S10Thinner
    % by weight: 100–200 %dealer% by volume: 100–200 %dealer

    Default: fastest drying and a harder film; patina wipes back harder — for crisp, high-contrast results.

    Thinned with S10 the patina is harder to rub off (t-colormarket).

  • S2000Thinner
    % by weight: 100–200 %dealer% by volume: 100–200 %dealer

    Dedicated patina thinner: dries slightly slower but the patina is easier to sand/rub back — more working time, larger parts.

  • S10 / S2000Thinner
    % by weight: 100–300 %catalog

    The catalogue allows up to 300 % for a very light, translucent glaze.

    Dealer text: 'thin 1–2 times with solvent'.

  • S10Thinner
    % by weight: 100 %schedule

    Official schedules: open-pore oak kitchen fronts, decapé oak fronts, PU-foam mouldings.

    1:1 in all three schedules.

  • ethanolThinner

    Ethyl alcohol — when you want the patina to wipe back more easily (soft, blended effect).

    No percentage given; work within the same 100–200 %.

Percentages are per 100 parts of component A.

Characteristics

Viscosity
17 sdealer
Drying · Full dry (min)
10dealer
Drying · Before removal (min)
5–10 mindealer
Drying · Conditions
20 °C
Fast drying
yescatalog
Removability
good hand removal; adjustable via thinner — ethanol easier, S10 harderdealer
Pot life
n/a — one-component, no hardenerrecommended

Colours

  • CQS10049 · white

Application

HVLP

Pressure · fluid
gravity cuprecommended
Consumption
80–100 g/m²dealer
Coats
1dealer
Flash-off
5–10 mindealer

Gun 15–20 cm off the part, overlapping passes, work the colour into pores, panel profiles and recesses; one coat. Wipe back after 5–10 min.

Conventional spray

Consumption
80–100 g/m²dealer

Lower transfer efficiency (up to 40 %), more overspray — use a booth.

Airmix (air-assisted airless)

Consumption
80–100 g/m²dealer

Production only; easy to over-apply at such low film weights — HVLP is usually better.

Cloth or pad

Consumption
80–100 g/m²catalog

Catalogue lists 'spray + rub': spray on, then rub in / wipe back. Rag or brush application only for small touch-ups.

Process and compatibility

Substrate preparation
Only over a cured, sanded primer or enamel (PU or acrylic). Sand primer P240–P320, profiles with K60–K120 pads (per the schedules). On open-pore oak keep the pores open — that is where the white sits.schedule
Goes over
ATS20 / APS20 / APL20 / APL20 SM / PPL20 / PPS20 / PPS20040 / PPS50 / APS20106 / PPS400XX / ATL20 SM
Goes under
ATL20 / ATL500 / PTL500 / ATL200 / ATL20 SM / ATL20 UM
Removal
After 5–10 min at 20–25 °C rub off the excess: Scotch-Brite 07448 / S UFN (oak, enamel), steel wool #2 (PU foam), or K600 abrasive (dealer instruction). The longer it dries, the harder it is to remove.
Sanding
Don't wipe back with anything coarser than P400/K600 — you'll cut through the enamel/primer beneath.recommended
Topcoat timing
Topcoat as soon as the excess is removed and dust blown off — same day (patina full dry ~10 min). Lay the first lacquer coat light so it doesn't lift or smear the patina.recommended
Temperature and humidity
20–25 °Cschedule
Don'ts
  • Don't apply to bare unprimed wood — it soaks in and won't wipe back
  • Don't leave patina without a clear topcoat — it's unprotected and rubs off
  • Don't let it dry too long before wiping back — fully dried it removes poorly
  • Not for exterior use (interior material)
Special effects
«Размытие» (blur): APS20106 → RAL enamel → CQS 21–26 patina → mist S10 from a gun at low pressure → ATL20 UM clear lacquer, Stone (jasper/granite): CQS/CTU dropped from a gun at minimum pressure + S10 drops, then ATL200, Metallic enamel: PPS50 → APL800XX → ATL20 SM → CQS → ATL20 SM

Storage

Shelf life
12 monthsdealer
Packaging
1 kg,5 kg,25 kgdealer

Safety: Use respiratory, hand and eye protection and overalls. Keep away from children. Dispose of waste at an authorised site; do not release into the environment. Solvent-borne, so flammable; spray in an extracted booth.

Used in finishing systems

Sources

Value tags: “official”, “dealer”, “catalog”, “schedule” are Technocolor data; “workshop” is from our own datasheets; “recommended” is our engineering estimate (hover to see the reasoning).

Not covered by the sources
  • no official t-color.ru page
  • solids %
  • density
  • storage temperature
  • no TDS PDF found
  • relationship to CQS10 (industrial / tinted / identical) not stated