PPL R9001 M
PPL R9001 M 2K PU enamel, cream white RAL 9001, matt (20 gloss)
Two-pack polyurethane enamel in cream white (RAL 9001), matt, 20 gloss. Excellent hide and flow, good chemical and scratch resistance. Can be used as a finish coat. Ready-made factory colour from the stock range, so the shade is consistent batch to batch.
- furniture fronts and MDF panels
- coloured base coat under special effects (liquid leaf, pearl) — special-effects catalog
Mix calculator
Ask about PPL R9001 M
Answers are based on the PPL R9001 M data and the products it mixes with.
Mixing matrix
- PC60Hardener% by weight: 50 %dealer% by volume: 60 %dealer
standard hardener
Catalog: PC60 30*–50 % (50 % for M, 30 % for DM). Every dealer M page: 50 % by weight / 60 % by volume.
- PC20Hardener% by weight: 50 %dealer% by volume: 60 %dealer
NOT listed for R9001 M — only on the dealer's R9005 M page; use only after checking with Technocolor
PC20 isn't stated for the other colours — check with Technocolor before using it there.
- S50Thinner% by weight: 20–30 (typ. 25) %dealer% by volume: 30–35 %dealer
universal, normal evaporation — default, vertical work
Catalog: S50 20–30 %. 25 % default is derived.
- S70Thinner% by weight: 20–30 %dealer% by volume: 30–35 %dealer
slow — above ~25 °C, large panels
More dust pick-up and sag risk on verticals; doesn't change full-cure time.
- % by weight: 50 %schedule
reference only: the 'PPU/PU mouldings' schedule ratio for PPL20 (RAL, NCS) — not stated for PPL R9001 M
No official schedule names PPL RAL. For R9001 M use PC60 at 50 %.
| Role | Material | % by weight | % by volume | When |
|---|---|---|---|---|
| Hardener | PC60 | 50 %dealer | 60 %dealer | standard hardenerCatalog: PC60 30*–50 % (50 % for M, 30 % for DM). Every dealer M page: 50 % by weight / 60 % by volume. |
| Hardener | PC20 | 50 %dealer | 60 %dealer | NOT listed for R9001 M — only on the dealer's R9005 M page; use only after checking with TechnocolorPC20 isn't stated for the other colours — check with Technocolor before using it there. |
| Thinner | S50 | 20–30 (typ. 25) %dealer | 30–35 %dealer | universal, normal evaporation — default, vertical workCatalog: S50 20–30 %. 25 % default is derived. |
| Thinner | S70 | 20–30 %dealer | 30–35 %dealer | slow — above ~25 °C, large panelsMore dust pick-up and sag risk on verticals; doesn't change full-cure time. |
| Hardener | PC20 / C61 | 50 %schedule | — | reference only: the 'PPU/PU mouldings' schedule ratio for PPL20 (RAL, NCS) — not stated for PPL R9001 MNo official schedule names PPL RAL. For R9001 M use PC60 at 50 %. |
Percentages are per 100 parts of component A.
Characteristics
- Solids
- 53 % part Acatalog
- Viscosity
- 12 ± 3 sdealer
- Gloss
- 20 ± 3 GU 60°dealer
- Pot life
- 4 h at 20 °Cdealer
- Drying · Touch-dry
- 30dealer
- Drying · Full cure
- 8dealer
- Drying · Sand or stack
- 8–16 (overnight)recommended
- Drying · Conditions
- 20 °C
- Hiding
- high hiding powerdealer
- Chemical resistance
- good physical-chemical and scratch resistancedealer
- Elasticity
- elastic, flows well in thin filmcatalog
- Colour stability
- colour consistency is computer-controlledcatalog
Colours
- PPL R9001 M · cream white, RAL 9001
Application
HVLP
- Consumption
- 150 g/m²dealer
- Spray viscosity
- 18–22 s DIN4/ВЗ-4recommended
- Nozzle
- 1.7–2 (typ. 1.8) mmrecommended
- Pressure · fluid
- gravity cup; pressure pot 0.8–1.2 barrecommended
- Pressure · air · Inlet pressure
- 2–2.5 bar (trigger pulled)
- Pressure · air · Cap
- 0.7 bar
- Pressure · air · Why ru
- Стандартный режим HVLP; настройка владельца для ATL50 (2,0–2,2 бар на входе) немного повышена для более тяжёлого пигментированного ПУ.
- Gun distance
- 15–20 cmrecommended
- Wet film
- 110–125 µmrecommended
- Coats
- 2 (one 150 g/m² coat per pass; second coat for full, even hide — especially R9005 black and the light RAL whites over white primer)recommended
- Flash-off
- 10–15 minrecommended
- Recoat
- wet-on-dry after ~30–60 min (touch dry) without sanding, or after full cure (8 h, ideally overnight) with a P400 scuffrecommended
- Sanding between coats
- P400–P500 or grey pad, denib onlyrecommended
HVLP, 1.8 mm tip (1.7–2.0), 2.0–2.5 bar inlet with trigger pulled, ≤0.7 bar at the cap, fan wide open, 15–20 cm, 50–75 % overlap.
Conventional spray
- Consumption
- 150 g/m²dealer
- Nozzle
- 1.6–1.8 mmrecommended
- Pressure · air
- 3–4 barrecommended
Dealer R9001 M page: 'spray: 150 g/m²'; the sibling R9003 M / R9005 M pages specify 'air (pneumatic) spray, 150 g/m² per coat'. Transfer efficiency up to 40 % (t-color.ru methods page).
Airmix (air-assisted airless)
- Nozzle
- 09–11 thou (0.23–0.28 mm), 40–50° fanrecommended
- Pressure · fluid
- 30–60 barrecommended
- Pressure · air
- 1–2 barofficial
For production runs of fronts. On DM keep film build even or sheen will vary.
Airless
- Nozzle
- 11–13 thou (0.28–0.33 mm)recommended
- Pressure · fluid
- 120–160 barrecommended
Not the preferred method for a finish enamel; use airmix instead.
Process and compatibility
- Substrate preparation
- MDF/wood primed with white PU primer (PPS20 2 coats, or PPS50277 — owner's datasheet: PC20/PC21 30 %, 1.8–2.0 mm), primer sanded P320–P400 and dedusted. A cream RAL 9001 hides easily over a white primer.recommended
- Goes under
- APL2xxxx (liquid leaf) / ATL2 + CS pastes (pearl) / ATL80018 / ATL22170 / ATL21226 / ATL500 / ATL200
- Sanding
- primer P320–P400; between enamel coats P400–P500/grey pad denib; never sand the final coatrecommended
- Temperature and humidity
- 18–25 °C material, room and substrate (not below 15 °C), RH 50–70 %recommended
- Don'ts
- don't go past the 4 h pot life at 20 °C
- don't lay heavy coats wet-on-wet — solvent pop risk
- don't polish or sand the final coat
- don't swap in PC20 on colours where it isn't listed without asking Technocolor
Storage
- Shelf life
- 8 месяцев / 8 months (при соблюдении условий хранения)dealer
- Storage temperature
- +5…+25 °C, closed original tins, away from heatrecommended
- Packaging
- 1, 5, 25 kgdealer
Safety: Use respiratory, hand and eye protection and overalls in production. Keep away from children. Dispose of waste at an approved site per current regulations; do not release to the environment.
Sources
Value tags: “official”, “dealer”, “catalog”, “schedule” are Technocolor data; “workshop” is from our own datasheets; “recommended” is our engineering estimate (hover to see the reasoning).
- official page — title only, no data (fetched 2026-10-05)
- dealer: description, gloss 20±3, viscosity 12±3 s CF8, pot life 4 h, touch 30 min, full 8 h, PC60 50/60, S50/S70 20–30/30–35, 150 g/m², packs 1/5/25 kg
- dealer sibling: shelf life 8 months, safety/disposal text, 'pneumatic spray 150 g/m²'
- dealer sibling: PC20 / PC60 alternative hardener (R9005 only), 'pneumatic spray 150 g/m²', safety text
- dealer: the DM (5 gloss) sibling, separate product
- schedule with PPL20 (analogue) C20/C61 50 %
- application methods: air spray transfer ≤40 %, airless ≤200 bar / ≤90 %, airmix ≤20 bar fluid + 1–2 bar air
Not covered by the sources
- official page is title-only (no data); all data from dealer + catalog
- solids for M only from catalog line-level figure (53 %), not stated per colour
- density
- hardness
- lightfastness value
- dust-free time
- stack/sand time (derived)
- spray nozzle/pressure (derived — no Technocolor value)
- shelf life only stated on sibling R9003 M page
- safety text only on sibling pages
- storage temperature
- no ТДС/TDS PDF found (web search returned nothing)
- not in any official finishing schedule