CQS41141
CQS41141 Gold patina (copper gold), metallic
Solvent-borne metallic patina in a copper-gold shade. Sprayed over PU or acrylic primers/enamels; once dry the excess is cut back by hand with steel wool or a Scotch-Brite pad, leaving gold in the pores, recesses, panel profiles and on the edges. Fast drying, easy to wipe back, very low consumption. Patina shades can be intermixed or layered one over another. Must always be locked in with a clear lacquer.
- decapé and distressed/aged effects on solid-wood and veneered furniture (interior)
- patina over enamelled raised-panel and carved doors (classic, Provence, Mediterranean styles)
- interior items, hardware, décor elements, picture frames/mouldings
- gold in the pores of open-pore oak
- PU-foam (PPU) mouldings and décor
- special effects: metallised enamel, Desert Rose (over HTL10001 frost)
Mix calculator
Ratio 100 : 100.0
| Component | Weigh out |
|---|---|
| CQS41141part A | 250 g |
| S10Thinner | 250 g |
| Total | 500 g |
Covers roughly 5.56 m² at 90 g/m².
Pot life of the mix: not applicable — 1K, no hardener.
Ask about CQS41141
Answers are based on the CQS41141 data and the products it mixes with.
Mixing matrix
- S10Thinner% by weight: 100–200 %official% by volume: 100–200 %official
default: fastest drying, harder film
dealer: 'cut 1–2 times with solvent'; S10 gives fast drying and a harder surface
- S2000Thinner% by weight: 100–200 %dealer
when you want the patina to cut back more easily
dealer: dries a touch slower but sands back easier; catalog: S2000 is fast, low-aggression, made for patinas
- S10Thinner% by weight: 100 %schedule
in all three official schedules (PU foam, decapé oak, open-pore oak)
also in https://www.t-color.ru/information/technology/otdelka-kuhonnyh-fasadov-iz-duba-s-effektom-decape-akr/ and https://www.t-color.ru/information/technology/otkrytoporistaya-otdelka-kuhonnyh-fasadov-iz-duba-akr/
- % by weight: 100–300 %catalog
catalog range for the whole CQS series (2022 and 2025–2026)
catalog allows up to 300 % — for a very light, sheer veil
- S13Thinner% by weight: not specified %catalog
allowed alternative: the catalog thinner table lists S13 for patinas
no dose given for CQS; roughly as S10 (100–200 %) — an estimate, not manufacturer data
| Role | Material | % by weight | % by volume | When |
|---|---|---|---|---|
| Thinner | S10 | 100–200 %official | 100–200 %official | default: fastest drying, harder filmdealer: 'cut 1–2 times with solvent'; S10 gives fast drying and a harder surface |
| Thinner | S2000 | 100–200 %dealer | — | when you want the patina to cut back more easilydealer: dries a touch slower but sands back easier; catalog: S2000 is fast, low-aggression, made for patinas |
| Thinner | S10 | 100 %schedule | — | in all three official schedules (PU foam, decapé oak, open-pore oak)also in https://www.t-color.ru/information/technology/otdelka-kuhonnyh-fasadov-iz-duba-s-effektom-decape-akr/ and https://www.t-color.ru/information/technology/otkrytoporistaya-otdelka-kuhonnyh-fasadov-iz-duba-akr/ |
| Thinner | S10 / S2000 | 100–300 %catalog | — | catalog range for the whole CQS series (2022 and 2025–2026)catalog allows up to 300 % — for a very light, sheer veil |
| Thinner | S13 | not specified %catalog | — | allowed alternative: the catalog thinner table lists S13 for patinasno dose given for CQS; roughly as S10 (100–200 %) — an estimate, not manufacturer data |
Percentages are per 100 parts of component A.
Characteristics
- Drying · Before wipe-back (min)
- 5–10 mindealer
- Drying · Before wipe-back (schedule)
- 5–10 minschedule
- Drying · Conditions
- 20–25 °C
- Fast drying
- yesofficial
- Removability
- wipes back easily by handofficial
- Type
- solvent-borne patinacatalog
- Intermixable
- shades can be mixed and layereddealer
- Tintable
- yescatalog
- Pot life
- not applicable — 1K, no hardenerrecommended
Colours
- CQS41141 · Copper gold
Application
HVLP
- Consumption
- 80–100 g/m²official
- Coats
- 1dealer
- Nozzle
- 1–1.3 mmrecommended
- Pressure · air
- 1.5–2 bar inletrecommended
- Pressure · fluid
- gravity cup; fluid needle ~1–1.5 turns openrecommended
- Spray viscosity
- 10–14 s DIN4recommended
- Gun distance
- 15–20 cmrecommended
- Flash-off
- 5–10 mindealer
Gun 15–20 cm off the work, one thin even coat, no runs; cut back only after 5–10 min dry. Metallic pigment settles — stir before filling and give the cup a shake now and then. Clean up with S10.
Conventional spray
- Consumption
- 80–100 g/m²official
- Nozzle
- 1.2–1.4 mmrecommended
- Pressure · air
- 2–3 barrecommended
The 'blur' effect (special-effects catalog p.20) is documented for the non-metallic CQS 21–26 patinas: the patina is softened with S10 sprayed at low pressure. Not stated for metallic CQS41141.
Cloth or pad
- Consumption
- 80–100 g/m²catalog
Spray on, then rub out / wipe back by hand: steel wool No.2 or Scotch-Brite 07448 S UFN.
Process and compatibility
- Substrate preparation
- sanded, dust-free PU or acrylic primer or enamel, fully cured; on oak open the pores with K60–K80 padsschedule
- Goes over
- PPS20 / PPS50 / PPS400XX / PPL20 / APL800XX / ATS20 / ATL20 SM / HTL10001 / APS20 / APL20 / PPS20040
- Wipe-back
- steel wool No.2 or Scotch-Brite 07448 S UFNschedule
- Sanding
- substrate before patina: P240–P320 then K120 pads (enamel; PPU schedule: K120 only) or K60–K80 (open pore)schedule
- Temperature and humidity
- 20–25 °Cschedule
- Don'ts
- never leave it without a clear lacquer top coat
- no heavy coats — one thin coat at 80–100 g/m²
- don't cut back before it's dry (5–10 min)
- exterior use not claimed by the maker — treat as interior only (estimate)
Storage
- Packaging
- 1 кг,5 кгdealer
Safety: Contains organic solvents, flammable. Spray in a booth with extraction, wear an organic-vapour respirator, keep away from ignition sources.
Used in finishing systems
Sources
Value tags: “official”, “dealer”, “catalog”, “schedule” are Technocolor data; “workshop” is from our own datasheets; “recommended” is our engineering estimate (hover to see the reasoning).
- official (fetched live): properties, spray 80–100 g/m², S10 100–200 % wt/vol
- dealer: description, cut 1–2x, S10/S2000 advice, one coat 80–100 g/m², dry 5–10 min, wipe-back, clear lacquer, 1/5 kg packs
- schedule: CQS 100 : S10 100, 80–100 g/m², 5–10 min, steel wool No.2, PTL500 top coat
- schedule: decapé oak, CQS:S10 100:100, 5 min, Scotch-Brite 07448, ATL20 top coat
- schedule: open-pore oak, CQS:S10 100:100, 5 min, ATL20 top coat
Not covered by the sources
- dealer page has NO 'Все технические характеристики' block: solids %, density, viscosity as supplied, full dry time all unknown
- gloss, lightfastness, chemical resistance unknown
- shelf life and storage temperature unknown
- no Technocolor TDS/SDS PDF found (web search budget exhausted; none found for sibling CQS codes)
- S13 dose not stated for CQS
- nozzle/pressure/spray viscosity derived only
- recoat window under lacquer not stated (schedules go straight to lacquer after wipe-back)
- schedules name generic 'CQS', not CQS41141 specifically
- official page not in local cache — fetched live 2026-10-05; text identical to CQS41001 page (generic CQS text)
- S2000 % by volume not given (dealer gives only 1–2x dilution)
- CQS41141 not among swatches on special-effects p13 (metallic patina) — systems use generic CQS / CQS 4XXXX