Skip to content
Dugan Design
← All products
+ Add to shopping list
Stains and dyesDye

CLT58

CLT58 Kromolux dye concentrate, Palisander (rosewood)

Highly concentrated transparent dye (binder-free stain) from Milesi's Kromolux series in Palisander (a dark reddish-brown rosewood tone; check the exact shade against a dealer sample). Very clear and even; at higher strength it goes dark while staying transparent. Dilutes with water or solvent, with or without a binder.

  • Staining all kinds of timber, veneer and solid
  • Furniture, profiles and frames, wooden articles in general
  • Toning and evening out colour variation under PE, PU and NC lacquers

Mix calculator

g
Thinner750.0 %

When: Slow — open-pored timber (oak, ash), large panels, hot shop: stays wet longer, fewer blotches and lap marks.

Additive

Ratio 100 : 750.0

ComponentWeigh out
CLT58part A58.8 g
S90Thinner441 g
Total500 g

Covers roughly 5.56 m² at 90 g/m².

Pot life of the mix: not applicable — single-component, no reaction; keep diluted mix closed and use within the shift.

Ask about CLT58

Answers are based on the CLT58 data and the products it mixes with.

Questions and answers are stored to improve the assistant and prevent abuse; the question text is processed by Anthropic (USA). Privacy policy

Mixing matrix

  • S10Thinner
    % by weight: 500–1000 %dealer% by volume: 500–1000 %dealer

    Fast, strong thinner — for fine-pored timber (beech, birch, maple, alder) and short flash-off between operations.

    Thinner selection per the Technocolor 2025–2026 catalog thinner table. S10 is also the gun-cleaning solvent per its official page.

  • S12Thinner
    % by weight: 500–1000 %dealer% by volume: 500–1000 %dealer

    Medium evaporation — medium-pored timber (cherry, walnut, tight ash); the default for a solvent-borne stain.

    S12 is the dye thinner per its official page, and it is the thinner used in the dye steps of the official schedules.

  • S90Thinner
    % by weight: 500–1000 %official% by volume: 500–1000 %official

    Slow — open-pored timber (oak, ash), large panels, hot shop: stays wet longer, fewer blotches and lap marks.

    Dealer lists S90 as 'slow dye thinner'.

  • WATERThinner
    % by weight: 500–1000 %dealer% by volume: 500–1000 %dealer

    Water dilution — less odour/VOC, raises the grain more and dries much slower (Milesi TDS: 8 h at 20 °C vs. minutes on solvent).

    Deionised (distilled) water only — tap water makes the dye flocculate and lose colour stability (dealer note). Before a water stain, raise the grain with a damp sponge, dry and denib at P180–P220.

  • LZC97Thinner
    % by weight: 500–1000 %official% by volume: 500–1000 %official

    Listed by Technocolor as a thinner. The Milesi TDS uses LZC97 as a small-share co-solvent alongside the main thinner (see the TDS rows).

    LZC97's exact function is not documented by Technocolor; no product page.

  • CFS1Additive
    % by weight: 0–200 %dealer% by volume: 0–200 %dealer

    Binder for the solvent-borne stain (with S10/S12/S90): locks the dye in, less bleeding/lifting when the sealer goes on, more even colour on end grain.

    Role: binder. CFS1 = solvent-borne and CFH1 = water-borne follows from the schedules (CFS1 paired with S12, CFH1 with water); the dealer's ОР/ВР labels are listed in the opposite order.

  • CFH1Additive
    % by weight: 0–200 %dealer% by volume: 0–200 %dealer

    Binder for the water-diluted stain.

    0 % = plain dye stain; with binder the colour holds better under the sealer.

  • LZC97 / LZC1000Thinner
    % by weight: CLT 1 : LZC97 0.5 : LZC1000 9.5 (≈ LZC97 50 % + LZC1000 950 %)datasheet

    Milesi's suggested solvent dilution. LZC1000 is a Milesi code; in the Technocolor line its place is taken by S10/S12/S90 per the official page.

  • LZC97 / WATERThinner
    % by weight: CLT 1 : LZC97 1 : water 14 (≈ LZC97 100 % + water 1400 %)datasheet

    Milesi's suggested water dilution.

  • LZC1000 / LZC1024 / LZC97 / LTC5 / WATERThinner
    % by weight: 500–800 %datasheet

    Milesi TDS: manual spray (5–20 g/m²), fixed automatic airmix/airless and swinging-arm guns (10–20 g/m²) — 500–800 %; automatic rotating (carousel) guns — 700–1500 % (5–20 g/m²).

  • CFS1 / S12Additive
    % by weight: CFS1 200 % + S12 500 %schedule

    Raised-panel doors (PU): stain 80–100 g/m², 5 min at 20–25 °C, then PTS20+C25+S50 sealer.

    The finishing schedule names the generic code 'CTU' (universal transparent dye). CLT58 has no t-color.ru page, but the CLT series (e.g. CLT4) sits in the same 'Universal dyes' section, and CTU28 Palisander carries the identical dilution table (S10/S12/S90/water 500–1000 %, CFS1/CFH1 0–200 %), so the recipe is carried over as a guide; that mapping is our interpretation, not an explicit CLT58 instruction.

  • CFS1 / S12Additive
    % by weight: CFS1 150 % + S12 500 %schedule

    Mouldings and frames (UV): stain 80 g/m², 5 min at 25–30 °C, then VTS40041 UV sealer.

    The finishing schedule names the generic code 'CTU' (universal transparent dye). CLT58 has no t-color.ru page, but the CLT series (e.g. CLT4) sits in the same 'Universal dyes' section, and CTU28 Palisander carries the identical dilution table (S10/S12/S90/water 500–1000 %, CFS1/CFH1 0–200 %), so the recipe is carried over as a guide; that mapping is our interpretation, not an explicit CLT58 instruction.

  • CFH1 / WATERAdditive
    % by weight: CFH1 400 % + вода/water 1000 %schedule

    Beech-veneered tabletops (PU): stain 80–100 g/m², 20 min at 20–25 °C, PTS60+C26+S50 sealer, PTL61+C61+S70 lacquer. (The t-color.ru page itself wrongly carries the header 'Open-pore oak kitchen fronts (acrylic)', but the content is the PU tabletop system.)

    This schedule is written for the water dye CTH, not CLT; 400 % CFH1 exceeds CLT58's official 0–200 % — stay within 0–200 % for CLT58.

Percentages are per 100 parts of component A.

Characteristics

Viscosity
24 ± 2 s, 24 ± 2 s
Drying · Conditions
20 °C, 70 % RH (TDS test conditions)
Drying · Room temp (solvent)
30 s (TDS prints 30" with LZC1000 thinner)datasheet
Drying · Room temp (water)
8 h (water thinner)datasheet
Drying · IR drying 60 °C (solvent)
10 mindatasheet
Drying · IR drying 60 °C (water)
20 mindatasheet
Pot life
not applicable — single-component, no reaction; keep diluted mix closed and use within the shiftrecommended
Thixotropy
norecommended
Gloss
not applicable — no filmrecommended

Colours

  • CLT58 · Palisander (rosewood)

Application

HVLP

Nozzle
1–1.3 mmrecommended
Pressure · fluid
gravity cup, no fluid pressurerecommended
Pressure · air
1.5–2 bar inlet (gun trigger pulled); ≈0.5–0.7 bar at caprecommended
Spray viscosity
as diluted (500–1000 %), ~water-thin — do not thin to a cup timerecommended
Consumption
80–100 g/m² ready mixdealer
Coats
1 even full wet pass (2 light crossing passes on large panels); add colour by a second pass, not by floodingrecommended
Flash-off · Solvent
5 min at 20–25 °C (CFS1+S12 mix)schedule
Flash-off · Water
20 min at 20–25 °C (CFH1+water mix)schedule
Recoat · Sealer (solvent)
after 1 min (thinned with LZC1000)datasheet
Recoat · Sealer (waterborne)
after 8 h at 20 °C (water thinner); TDS IR + warm air 60 °C drying = 20 mindatasheet
Sanding between coats
do not sand the stain coat itself; denib the first sealer coat at P240–P320recommended
Concentrate consumption (g/m²)
5–20 g/m² (TDS 'quantities', manual spray — reads as concentrate)datasheet

Hold the gun square at 15–20 cm, 50 % overlap. On profiles do edges and recesses first, then the field. Stir the mix before filling.

Conventional spray

Nozzle
1–1.2 mmrecommended
Pressure · air
2–3 bar at gunrecommended
Consumption
80–100 g/m² ready mixdealer
Concentrate consumption (g/m²)
5–20 g/m² (TDS 'quantities', manual spray — reads as concentrate)datasheet

Classic air spray — the mainstream method per the methods page (up to 40 % transfer).

Airmix (air-assisted airless)

Nozzle
0.18–0.23 mm (07–09 thou), narrow 20–40° fanrecommended
Pressure · fluid
4–8 barrecommended
Pressure · air
0.8–1.5 barrecommended
Concentrate consumption (g/m²)
10–20 g/m² (TDS, fixed automatic AIR-MIX gun — reads as concentrate)datasheet
Dilution
500–800 %datasheet

The Milesi TDS gives 10–20 g/m² for fixed automatic airmix at 500–800 % dilution — that reads as concentrate, i.e. ≈60–180 g/m² of ready mix, consistent with the dealer's 80–100 g/m².

Airless

Nozzle
0.18–0.23 mm (07–09 thou)recommended
Pressure · fluid
30–60 barrecommended
Concentrate consumption (g/m²)
10–20 g/m² (TDS, fixed automatic AIR-LESS gun — reads as concentrate)datasheet
Dilution
500–800 %datasheet

For hand work prefer airmix/HVLP — airless has a coarser fan and more blotch risk.

Automatic rotating spray

Dilution
700–1500 %datasheet
Concentrate consumption (g/m²)
5–20 g/m²datasheet

Automatic rotating (carousel) guns per the Milesi TDS: 700–1500 % dilution, 5–20 g/m² concentrate. Electrostatic application is not mentioned for CLT in any source.

Process and compatibility

Substrate preparation
Sand flats P150 → P180 → P220; profiles with sanding mats/sponges K60–K80schedule
Goes over
bare sanded wood
Sanding
Never sand the dyed surface directly; sand the first sealer coat P240–P320 (flats) / K120 (profiles) per schedulerecommended
Temperature and humidity
TDS data at 20 °C / 70 % RHdatasheet
Don'ts
  • Don't dilute with tap water — deionised only
  • Don't exceed 200 % CFS1/CFH1 binder
  • Don't flood the surface — make a second light pass instead
  • Don't sand the bare dye coat — sand the sealer
  • Don't seal a water-diluted stain before it is fully dry (TDS: ~8 h at 20 °C or 20 min at 60 °C)

Storage

Shelf life
8 months from delivery (series TDS; CLT58 not named)datasheet
Storage temperature
18–25 °C, tightly closed, protected from moisturedatasheet
Packaging
1 Ldealer

Safety: Composition and hazard class are not published (no CLT58 SDS found). Treat the concentrate and S10/S12/S90 mixes as flammable: spray in an extracted booth, no ignition sources, A2P2 respirator and nitrile gloves; keep solvent rags in a closed metal bin.

Used in finishing systems

Sources

Value tags: “official”, “dealer”, “catalog”, “schedule” are Technocolor data; “workshop” is from our own datasheets; “recommended” is our engineering estimate (hover to see the reasoning).

Not covered by the sources
  • solids_pct (blank in Milesi TDS, not on official/dealer pages)
  • lightfastness rating (no sourced figure)
  • hardness/elasticity/chemical resistance — not applicable to a binder-free dye on its own
  • LZC97 function and Technocolor product page (no official or dealer page)
  • CFS1/CFH1 product pages and their own data (no official/dealer page found)
  • TDS room-temp drying with solvent printed as 30" (seconds by the TDS's own notation) vs 5 min in Technocolor schedules — use the schedule figure in practice
  • consumption discrepancy: dealer 80–100 g/m² (ready mix) vs Milesi TDS 5–20 g/m² (apparently concentrate)
  • SDS / hazard classification for CLT58
  • no Technocolor-issued TDS for CLT58; data sheet used is Milesi's (IVM) CLT series TDS, rev. I, Oct 2006
  • CLT not covered in Technocolor 2025–2026 catalog (only CTU/CPS/CTH/CPH dyes)
  • no official t-color.ru page for CLT58; LZC97 as thinner comes only from sibling CLT4 official page (dealer table for CLT58 does not list it)
  • exact colour tone/whether CLT58 is a base or composed colour; CLT58 absent from the 2006 Milesi TDS colour list — density/SG unknown; series viscosity/drying assumed to apply
  • t-color.ru page for the beech-tabletop schedule (otdelka-stoleshnits-oblitsovannyh-shponom-buka-pu) carries the wrong header 'Открытопористая отделка кухонных фасадов из дуба (Акр.)'; content is PU