PPL R1013 DM
PPL R1013 DM — 2K polyurethane enamel, pearl white / beige (RAL 1013), dead flat (5 gloss)
Two-pack polyurethane enamel, factory-tinted to RAL 1013 (pearl white, a warm off-white/beige), dead flat. High hide, good physical and chemical resistance; flows out well in a thin film, stays flexible, shade is batch-consistent. Finish coat for furniture fronts and MDF panels. No official t-color.ru page exists — data comes from the t-colormarket.ru product card.
- furniture fronts and MDF panels
- interior furniture and wood/MDF items
- coloured base under special effects (liquid leaf, pearl) — special-effects catalog, 'PPL RAL'
Mix calculator
Ask about PPL R1013 DM
Answers are based on the PPL R1013 DM data and the products it mixes with.
Mixing matrix
- PC60Hardener% by weight: 50 %dealer% by volume: 60 %dealer
primary ratio on the dealer card for R1013 DM
Catalog for PPL RAL: PC60 30*–50 %, the asterisk marking the DM variants (30 %). The R1013 DM card says 50/60 — the matt M figure (probably copied from the M/UM template). If the tin label or batch certificate says 30 %, use 30 %.
- PC60Hardener% by weight: 30 %dealer% by volume: 40 %dealer
if the batch paperwork confirms the DM formula (catalog: 30* for DM)
Every other PPL DM enamel at the dealer (R9001/R9003/R9005 DM, PPL20 DM) is PC60 30 % by weight / 40 % by volume, thinner S50 only at 20–30 % by weight / 30–45 % by volume. Not confirmed for R1013 DM.
- S50Thinner% by weight: 20–30 (typ. 25) %dealer% by volume: 30–35 %dealer
normal conditions 18–25 °C, vertical work
S50 — universal, normal evaporation. 25 % default is mid-range (our pick). Catalog: S50 20–30 %.
- S70Thinner% by weight: 20–30 %dealer% by volume: 30–35 %dealer
above ~25 °C, large panels, when you need longer open time
S70 — slow PU thinner. More flow-out time but more dust pick-up and sag risk; does not change cure time.
- % by weight: 50 %schedule
official schedule 'Finishing PU-foam parts', step 4 — RAL enamel as the intermediate coat under patina
The schedule says 'PPL20 (RAL, NCS)' with hardener 'С20 (С61)' — legacy/alternative codes; current is PC60. The 50 % amount matches the dealer card.
- S50Thinner% by weight: 30 %schedule
PU-foam schedule, step 4
| Role | Material | % by weight | % by volume | When |
|---|---|---|---|---|
| Hardener | PC60 | 50 %dealer | 60 %dealer | primary ratio on the dealer card for R1013 DMCatalog for PPL RAL: PC60 30*–50 %, the asterisk marking the DM variants (30 %). The R1013 DM card says 50/60 — the matt M figure (probably copied from the M/UM template). If the tin label or batch certificate says 30 %, use 30 %. |
| Hardener | PC60 | 30 %dealer | 40 %dealer | if the batch paperwork confirms the DM formula (catalog: 30* for DM)Every other PPL DM enamel at the dealer (R9001/R9003/R9005 DM, PPL20 DM) is PC60 30 % by weight / 40 % by volume, thinner S50 only at 20–30 % by weight / 30–45 % by volume. Not confirmed for R1013 DM. |
| Thinner | S50 | 20–30 (typ. 25) %dealer | 30–35 %dealer | normal conditions 18–25 °C, vertical workS50 — universal, normal evaporation. 25 % default is mid-range (our pick). Catalog: S50 20–30 %. |
| Thinner | S70 | 20–30 %dealer | 30–35 %dealer | above ~25 °C, large panels, when you need longer open timeS70 — slow PU thinner. More flow-out time but more dust pick-up and sag risk; does not change cure time. |
| Hardener | PC20 / C61 | 50 %schedule | — | official schedule 'Finishing PU-foam parts', step 4 — RAL enamel as the intermediate coat under patinaThe schedule says 'PPL20 (RAL, NCS)' with hardener 'С20 (С61)' — legacy/alternative codes; current is PC60. The 50 % amount matches the dealer card. |
| Thinner | S50 | 30 %schedule | — | PU-foam schedule, step 4 |
Percentages are per 100 parts of component A.
Characteristics
- Solids
- 62 ± 1 % part Adealer
- Viscosity
- 12 ± 3 sdealer
- Density
- 1.2–1.35 g/cm³ (part A)recommended
- Gloss
- 10 ± 3 GU 60°dealer
- Pot life
- 4 h at 20 °Cdealer
- Drying · Dust-free
- 10–15 minrecommended
- Drying · Touch-dry
- 30dealer
- Drying · Sand or stack
- 4schedule
- Drying · Full cure
- 8dealer
- Drying · Conditions
- 20 °C
- Hiding
- high hiding powerdealer
- Chemical resistance
- good physical and chemical resistancedealer
- Elasticity
- flexible, flows well in thin filmcatalog
- Thixotropy
- norecommended
Colours
- PPL R1013 DM · pearl white / beige (RAL 1013)
Application
HVLP
- Consumption
- 150 g/m²dealer
- Spray viscosity
- 20–24 s DIN4/ВЗ-4recommended
- Nozzle
- 1.7–2 (typ. 1.8) mmrecommended
- Pressure · fluid
- gravity cup; pressure pot 0.8–1.2 barrecommended
- Pressure · air · Inlet pressure
- 2–2.5 bar (trigger pulled)
- Pressure · air · Cap
- 0.7 bar
- Pressure · air · Why ru
- Стандарт HVLP (≤0,7 бар на воздушной головке); настройка владельца для ATL50 (2,0–2,2 бар на входе) чуть повышена для более тяжёлого пигментированного ПУ.
- Gun distance
- 15–20 cmrecommended
- Wet film
- 125–135 µmrecommended
- Coats
- 2 (1 may hide over white primer)recommended
- Flash-off
- 10–15 minrecommended
- Recoat
- wet-on-dry after 30–60 min without sanding, or after full cure (8 h, ideally overnight) with a P400 scuffrecommended
- Sanding between coats
- P400–P500 or grey pad, denib onlyrecommended
HVLP, 1.8 mm tip (1.7–2.0), 2.0–2.5 bar at the inlet with trigger pulled, ≤0.7 bar at the cap, fan wide open, 15–20 cm, 50–75 % overlap. Dead-flat enamel: stir part A thoroughly before mixing (the matting agent settles) and don't lay it on heavy — thick wet films go blotchy in sheen.
Conventional spray
- Consumption
- 150 g/m²dealer
- Nozzle
- 1.6–1.8 mmrecommended
- Pressure · air
- 3–4 barrecommended
Dealer states 'spray: 150 g/m²'. Air spray has low transfer efficiency (methods page) — fine for one-offs.
Airmix (air-assisted airless)
- Nozzle
- 09–11 thou (0.23–0.28 mm), 40–50° fanrecommended
- Pressure · fluid
- 10–20 barofficial
- Pressure · air
- 1–2 barofficial
For production runs of fronts. On dead-flat enamel keep the film even or the sheen will vary.
Airless
- Nozzle
- 11–13 thou (0.28–0.33 mm)recommended
- Pressure · fluid
- 120–160 barrecommended
Not the preferred method for a finish enamel — use airmix.
Process and compatibility
- Substrate preparation
- MDF/wood primed with white PU primer (PPS20 ×2 or PPS50277), primer sanded P320–P400 and dedustedrecommended
- Goes under
- CQS patina (schedule) / APL2xxxx liquid leaf / ATL2 + CS pearl / ATL80018 / ATL22170 / ATL500 / ATL200
- Sanding
- primer P320–P400; between enamel coats P400–P500/grey pad denib; never sand or polish the final coatrecommended
- Temperature and humidity
- 18–25 °C material, room and substrate (not below 15 °C), RH 50–70 %recommended
- Don'ts
- don't go past the 4 h pot life at 20 °C
- don't pile on heavy coats wet-on-wet — solvent pop
- don't sand or polish the final coat
- don't thin past 30 % — dead flat loses flatness and hide
- don't eyeball the hardener — weigh it, and confirm 30 vs 50 % PC60 for your batch first
Storage
- Shelf life
- 8 monthsdealer
- Storage temperature
- +5…+25 °C, closed original tins, away from heatrecommended
- Packaging
- package size not stated ('Упаковка, кг: –', priced per шт on the R1013 DM card); 'под заказ' — supplied to orderdealer
Safety: Wear PPE: respiratory, hand and eye protection, overalls. Keep away from children. Dispose of waste per regulations. PC60 hardener contains isocyanates — A2/P2 respirator or supplied air, good extraction.
Used in finishing systems
Sources
Value tags: “official”, “dealer”, “catalog”, “schedule” are Technocolor data; “workshop” is from our own datasheets; “recommended” is our engineering estimate (hover to see the reasoning).
- dealer card PPL R1013 DM (on slug ppl_20_um): properties, use, 150 g/m², PC60 50/60, S50/S70 20–30/30–35, gloss 10±3, solids 62±1 %, viscosity 12±3 s CF8, pot life 4 h, touch 30 min, full 8 h
- dealer search — only hit is the ppl_20_um card
- official page of the matt sibling R1013 M (properties only)
- dealer R1013 M card (same mix table, 20 ± 3 gloss) — comparison
- dealer R9005 DM card — DM-sibling ratio PC60 30/40, S50 20–30/30–45, 5 ± 3 gloss, 61 ± 1 % solids, 8 ± 2 s CF-8, 'stir thoroughly' (R9001 DM, R9003 DM, PPL20 DM cards identical)
- dealer R9003 M card — shelf life 8 months, safety text
- official schedule PU foam: PPL20 (RAL,NCS) 100 : C20(C61) 50 : S50 30, 150 g/m², dry 4 h
- application methods: airless up to 200 bar; airmix fluid up to 20 bar, air 1–2 bar; air spray transfer efficiency up to 40 %
Not covered by the sources
- no official t-color.ru page for R1013 DM (official has R1013 M only); not listed in the 2025–2026 catalog PPL RAL variant list either
- gloss conflict on dealer card: title 5 гл vs spec 10 ± 3 GU
- hardener conflict: dealer card PC60 50 % wt / 60 % vol vs catalog DM asterisk and every other PPL DM at 30 % wt / 40 % vol
- density (derived only)
- dust-free time (derived only)
- hardness
- lightfastness value
- official spray parameters/nozzle (all derived)
- shelf life only on sibling R9003 M card
- packaging sizes not stated (sold per kg, to order)
- no ТДС/TDS PDF found (web search unavailable; other dealers lakokraska31/ndom31/woodonline have no R1013 DM listing)