PPL R**** M
PPL RAL M — pre-tinted 2K polyurethane enamel, matt (20 gloss), stock RAL range
Factory-tinted 2K polyurethane enamel in popular RAL colours. Excellent strength properties, excellent hide and flow in thin film, elastic, good chemical and scratch resistance; shade is batch-consistent (computer-controlled tinting). Used as a finish coat.
- furniture fronts and MDF panels
- interior furniture and wood/MDF items
- coloured base coat under special effects (liquid leaf, pearl) — special-effects catalog
Mix calculator
Ask about PPL R**** M
Answers are based on the PPL R**** M data and the products it mixes with.
Mixing matrix
- PC60Hardener% by weight: 50 %dealer% by volume: 60 %dealer
standard hardener
Catalog: PC60 30*–50 % (50 % for M, 30 % for DM). Every dealer M page: 50 % by weight / 60 % by volume.
- PC20Hardener% by weight: 50 %dealer% by volume: 60 %dealer
alternative to PC60; dealer lists PC20/PC60 only on the R9005 M page
PC20 isn't stated for the other colours — check with Technocolor before using it there.
- S50Thinner% by weight: 20–30 (typ. 25) %dealer% by volume: 30–35 %dealer
universal, normal evaporation — default, vertical work
Catalog: S50 20–30 %. 25 % default is derived (mid-range).
- S70Thinner% by weight: 20–30 %dealer% by volume: 30–35 %dealer
slow — above ~25 °C, large panels
Dealer gives S50/S70 as one row: 20–30 % by weight / 30–35 % by volume. More dust pick-up and sag risk on verticals; doesn't change full-cure time.
| Role | Material | % by weight | % by volume | When |
|---|---|---|---|---|
| Hardener | PC60 | 50 %dealer | 60 %dealer | standard hardenerCatalog: PC60 30*–50 % (50 % for M, 30 % for DM). Every dealer M page: 50 % by weight / 60 % by volume. |
| Hardener | PC20 | 50 %dealer | 60 %dealer | alternative to PC60; dealer lists PC20/PC60 only on the R9005 M pagePC20 isn't stated for the other colours — check with Technocolor before using it there. |
| Thinner | S50 | 20–30 (typ. 25) %dealer | 30–35 %dealer | universal, normal evaporation — default, vertical workCatalog: S50 20–30 %. 25 % default is derived (mid-range). |
| Thinner | S70 | 20–30 %dealer | 30–35 %dealer | slow — above ~25 °C, large panelsDealer gives S50/S70 as one row: 20–30 % by weight / 30–35 % by volume. More dust pick-up and sag risk on verticals; doesn't change full-cure time. |
Percentages are per 100 parts of component A.
Characteristics
- Solids
- 53 % part Acatalog
- Viscosity
- 12 ± 3 sdealer
- Gloss
- 20 ± 3 GU (dealer: 'Глосс'; measuring angle not stated — 60° assumed)dealer
- Pot life
- 4 h at 20 °Cdealer
- Drying · Touch-dry
- 30dealer
- Drying · Full cure
- 8dealer
- Drying · Sand or stack
- 8–16 (overnight)recommended
- Drying · Conditions
- 20 °C
- Hiding
- high hiding powerofficial
- Chemical resistance
- good physical-chemical resistanceofficial
- Elasticity
- excellent strength properties, good flow in thin film, elasticcatalog
- Colour stability
- colour consistency is computer-controlledcatalog
Colours
- PPL R1013 M · oyster white (RAL 1013)
- PPL R1015 M · light ivory (RAL 1015)
- PPL R7047 M · telegrey 4, light grey (RAL 7047)
- PPL R9001 M · cream (RAL 9001)
- PPL R9003 M · signal white (RAL 9003)
- PPL R9005 M · jet black (RAL 9005)
- PPL R9010 M · pure white (RAL 9010)
- PPL R9016 M · traffic white (RAL 9016)
- PPL R7016 M · anthracite grey (RAL 7016)
Application
HVLP
- Consumption
- 150 g/m²dealer
- Spray viscosity
- 18–22 s DIN4/ВЗ-4recommended
- Nozzle
- 1.7–2 (typ. 1.8) mmrecommended
- Pressure · fluid
- gravity cup; pressure pot 0.8–1.2 barrecommended
- Pressure · air · Inlet pressure
- 2–2.5 bar (trigger pulled)
- Pressure · air · Cap
- 0.7 bar
- Pressure · air · Why ru
- Стандартный режим HVLP; настройка владельца для ATL50 (2,0–2,2 бар на входе) немного повышена для более тяжёлого пигментированного ПУ.
- Gun distance
- 15–20 cmrecommended
- Wet film
- 110–125 µmrecommended
- Coats
- 2 (one ~150 g/m² coat per pass; the second coat evens out colour and sheen — needed most on R9005 black and the greys R7016/R7047 over white primer; whites over white primer often hide in one)recommended
- Flash-off
- 10–15 minrecommended
- Recoat
- wet-on-dry after ~30–60 min (touch dry) without sanding, or after full cure (8 h, ideally overnight) with a P400 scuffrecommended
- Sanding between coats
- P400–P500 or grey pad, denib onlyrecommended
HVLP, 1.8 mm tip (1.7–2.0), 2.0–2.5 bar inlet with trigger pulled, ≤0.7 bar at the cap, fan wide open, 15–20 cm, 50–75 % overlap.
Conventional spray
- Consumption
- 150 g/m²dealer
- Nozzle
- 1.6–1.8 mmrecommended
- Pressure · air
- 3–4 barrecommended
Air spray is the method the dealer states ('air spray, 150 g/m² per coat'). Transfer efficiency up to ~40 % (methods page).
Airmix (air-assisted airless)
- Nozzle
- 09–11 thou (0.23–0.28 mm), 40–50° fanrecommended
- Pressure · fluid
- 50–80 barrecommended
- Pressure · air
- 1–2 barrecommended
For production runs of fronts. On DM keep film build even or sheen will vary.
Airless
- Nozzle
- 11–13 thou (0.28–0.33 mm)recommended
- Pressure · fluid
- 120–160 barrecommended
Not the preferred method for a finish enamel; use airmix instead.
Process and compatibility
- Substrate preparation
- MDF/wood primed with white PU primer (PPS20 2 coats, or PPS50277), primer sanded P320–P400 and dedustedrecommended
- Goes under
- APL2xxxx (liquid leaf) / ATL2 + CS pastes (pearl) / ATL80018 / ATL22170 / ATL21226 / ATL500 / ATL200
- Sanding
- primer P320–P400; between enamel coats P400–P500/grey pad denib; never sand the final coatrecommended
- Temperature and humidity
- 18–25 °C material, room and substrate (not below 15 °C), RH 50–70 %recommended
- Don'ts
- don't go past the 4 h pot life at 20 °C
- don't lay heavy coats wet-on-wet — solvent pop risk
- don't polish or sand the final coat
- don't swap in PC20 on colours where it isn't listed without asking Technocolor
Storage
- Shelf life
- 8 месяцев / 8 months (при соблюдении условий хранения)dealer
- Storage temperature
- +5…+25 °C, closed original tins, away from heatrecommended
- Packaging
- 1, 5, 25 kgdealer
Safety: Use respiratory, hand and eye protection and overalls in production. Keep away from children. Dispose of waste at an approved site per regulations; do not release to the environment. The hardener contains isocyanates — use an A2/P2 organic-vapour respirator or supplied air.
Sources
Value tags: “official”, “dealer”, “catalog”, “schedule” are Technocolor data; “workshop” is from our own datasheets; “recommended” is our engineering estimate (hover to see the reasoning).
- official page (properties only)
- official page (properties only)
- official page (properties only)
- official page (properties only)
- official page (properties only)
- official page (properties only)
- dealer: gloss, viscosity, pot life, drying, PC60 50/60, S50/S70 20–30/30–35
- dealer: gloss, viscosity, pot life, drying, PC60 50/60, S50/S70 20–30/30–35
- dealer: gloss, viscosity, pot life, drying, PC60 50/60, S50/S70 20–30/30–35
- dealer: gloss, viscosity, pot life, drying, PC60 50/60, S50/S70 20–30/30–35
- dealer: gloss, viscosity, pot life, drying, PC60 50/60, S50/S70 20–30/30–35
- dealer: gloss, viscosity, pot life, drying, PC60 50/60, S50/S70 20–30/30–35
Not covered by the sources
- no official mixing ratios (official pages give only properties)
- solids for M only from catalog (53 %; same figure as APL RAL row — possibly a catalog copy, DM dealer says 61 %)
- no dealer page for R7047 M and R7016 M
- R7016 M only in catalog
- density
- hardness
- lightfastness value
- dust-free time
- PC20 stated only for R9005 M
- official spray parameters/nozzle (derived)
- no ТДС/TDS PDF found (web search budget exhausted this session)