CPS021
CPS021 Solvent-borne pigment wood stain, Teak
Ready-mixed solvent-borne pigment stain in a teak shade — a warm golden brown. Evens out colour variation and hides wood defects, levels well and is lightfast. Comes practically ready to spray: let down 0-100 % with S10/S12/S90 if needed. Spray, spray-and-wipe or roller-coat; overcoat with primer after 20 minutes.
- Staining furniture in any wood species
- Teak look on pale or cheaper species (beech, birch, pine, alder)
- Evening out colour on solid wood and veneer
- Pore highlighting on open-grain wood (wipe-on)
- Tinting other solvent-borne stains
Mix calculator
Ask about CPS021
Answers are based on the CPS021 data and the products it mixes with.
Mixing matrix
- % by weight: 0–100 %dealer% by volume: 0–100 %dealer
S10 — fast, for fine-pore wood (beech, birch, maple, alder) and small parts; S12 — medium, general use; S90 — slow, for open-grain wood (oak, ash), big panels and hot shops — gives more working time for wiping.
Ready colour: can be sprayed neat; up to 100 % thinner gives a lighter, more see-through teak. The dealer pairs it with S90 and S12.
- % by weight: 500–1000 %catalog
S10 — fast, for fine-pore wood (beech, birch, maple, alder) and small parts; S12 — medium, general use; S90 — slow, for open-grain wood (oak, ash), big panels and hot shops — gives more working time for wiping.
2025/26 catalog figure for the whole CPS series, written for the concentrates; for ready-mixed CPS021 the dealer's 0-100 % applies.
- CFS1Additive% by weight: 0–400 %official% by volume: 0–400 %official
'With the special binder it can be wiped on' — for a pore-highlight effect on oak/ash.
Officially 0-400 % CFS1 for the CPS concentrates; the dealer lists no binder for CPS021 — test on a sample first.
- CFC3Additive% by weight: 200 %schedule
Flat anegre-veneered panels under a UV system, 60-80 g/m². The schedule doesn't state how the stain is applied (60-80 g/m² is a spray-level rate, not the 10-20 g/m² roller rate). It names the CPS series, not a specific colour.
- S90Thinner% by weight: 200 %schedule
Same anegre-veneer UV schedule.
| Role | Material | % by weight | % by volume | When |
|---|---|---|---|---|
| Thinner | S10 / S12 / S90 | 0–100 %dealer | 0–100 %dealer | S10 — fast, for fine-pore wood (beech, birch, maple, alder) and small parts; S12 — medium, general use; S90 — slow, for open-grain wood (oak, ash), big panels and hot shops — gives more working time for wiping.Ready colour: can be sprayed neat; up to 100 % thinner gives a lighter, more see-through teak. The dealer pairs it with S90 and S12. |
| Thinner | S10 / S12 / S90 | 500–1000 %catalog | — | S10 — fast, for fine-pore wood (beech, birch, maple, alder) and small parts; S12 — medium, general use; S90 — slow, for open-grain wood (oak, ash), big panels and hot shops — gives more working time for wiping.2025/26 catalog figure for the whole CPS series, written for the concentrates; for ready-mixed CPS021 the dealer's 0-100 % applies. |
| Additive | CFS1 | 0–400 %official | 0–400 %official | 'With the special binder it can be wiped on' — for a pore-highlight effect on oak/ash.Officially 0-400 % CFS1 for the CPS concentrates; the dealer lists no binder for CPS021 — test on a sample first. |
| Additive | CFC3 | 200 %schedule | — | Flat anegre-veneered panels under a UV system, 60-80 g/m². The schedule doesn't state how the stain is applied (60-80 g/m² is a spray-level rate, not the 10-20 g/m² roller rate). It names the CPS series, not a specific colour. |
| Thinner | S90 | 200 %schedule | — | Same anegre-veneer UV schedule. |
Percentages are per 100 parts of component A.
Characteristics
- Components
- 1K stain (+ optional thinner)dealer
- Carrier
- solvent-borne (органоразбавимый, «ОР»)dealer
- Lightfastness
- good (светостойкость)dealer
- Hiding
- high (высокая укрывистость)catalog
- Levelling
- good (хорошая выравнивающая способность)dealer
- Pot life
- n/a (no hardener)recommended
- Gloss
- none (no film)catalog
- Drying · Conditions
- 20 °C
- Drying · Full dry (min)
- 20 mindealer
- Drying · Line flash-off (min)
- 5 minschedule
Colours
- CPS021 · teak
Application
HVLP
- Nozzle
- 1.2–1.4 (typ. 1.3) mmrecommended
- Pressure · air
- 1.5–2 barrecommended
- Spray viscosity
- 10–14 s DIN4recommended
- Consumption
- 80–100 g/m²dealer
- Flash-off
- 20 mindealer
- Wet film
- 85–120 µmrecommended
- Sanding between coats
- None — never sand the stain.recommended
Stir well before and during use — the pigment settles. Teak is a warm golden brown: on pale woods (beech, birch) it lays down more evenly with S10/S12; on oak/ash the pigment packs into the pores, so wipe straight after spraying. One even wet coat, go lighter on end grain (it drinks more and goes darker). Always do a test panel on the same species.
Conventional spray
- Nozzle
- 1.2–1.4 (typ. 1.3) mmrecommended
- Pressure · air
- 2–3 barrecommended
- Consumption
- 80–100 g/m²dealer
More overspray than HVLP: open the fan wide, hold the gun 20-25 cm off.
Cloth or pad
Wiping with a sponge or soft rag removes the excess layer after application (Technocolor's method definition). For a pore-highlight effect on oak/ash use a binder (CFS1 per the official CPS9 page).
Roller coater (UV)
Flat parts on a roller-coater line only (official series rate 10-20 g/m²). The separate anegre UV schedule gives CPS+CFC3+S90 at 60-80 g/m² without naming the method — that is a spray-level rate, not a roller rate.
Airmix (air-assisted airless)
- Nozzle
- 09/40-11/40 tip (0.23-0.28 mm)recommended
- Pressure · fluid
- 8–15 barrecommended
- Pressure · air
- 1–2 barofficial
For production lines; HVLP is plenty in a workshop.
Process and compatibility
- Substrate preparation
- Sand P150 → P180 → P220 (belt), de-dust.schedule
- Sanding
- Never sand the stain itself. Sand only the first primer coat (P280-P320); if you cut through to the stain, touch it up.recommended
- Temperature and humidity
- 15-25 °C, RH ≤ 75 %recommended
Storage
- Packaging
- 1 л / 5 лdealer
Used in finishing systems
Sources
Value tags: “official”, “dealer”, “catalog”, “schedule” are Technocolor data; “workshop” is from our own datasheets; “recommended” is our engineering estimate (hover to see the reasoning).
- dealer CPS021 page: properties, use, S10/S12/S90 0-100 %, instruction CPS 80-100 g/m² → 20 min → PTS20 → PTL20 SM, 1/5 л, price
- official CPS9 page (same series; application rates)
- 2022 catalog CPS colour list incl. CPS021 тик
- UV anegre schedule CPS/CFC3/S90
- application methods (airmix pressures)
- sibling ready colour CPS037 with the same 0-100 % thinner table
Not covered by the sources
- no official t-color.ru page for CPS021 (data from dealer page + CPS9 official page + catalogs)
- no 'Все технические характеристики' block on dealer page: solids %, viscosity as supplied, density unknown
- drying only as 'сушка 20 мин' from dealer instruction; no dust-free/touch split
- shelf life
- storage temperature
- SDS/hazard data
- CFS1 binder ratio for ready colours not published
- CFC3 binder in the UV schedule undocumented elsewhere
- conflict: dealer thinner 0-100 % vs catalog series 500-1000 % (catalog figure is for concentrates)
- official nozzle/pressure not published (derived)
- no Technocolor TDS PDF found for CPS series
- anegre UV schedule does not state stain application method (60-80 g/m² implies spray)