VTL30020
UV-curing spray lacquer for furniture, 20 gloss (clear)
Clear matt (20 gloss) UV-curing lacquer for spraying furniture. Excellent flow-out, high clarity, good chemical/physical resistance, scratch- and rub-resistant, levels well in thin films. It is solvent-borne (part A solids 44–46 %), so the film must be flashed/pre-dried to drive off the thinner before UV curing.
Mix calculator
Ratio 100 : 25.0
| Component | Weigh out |
|---|---|
| VTL30020part A | 400 g |
| S30Thinner | 100 g |
| Total | 500 g |
Covers roughly 4.17 m² at 120 g/m².
Pot life of the mix: n/a — single-pack UV, no hardener.
Ask about VTL30020
Answers are based on the VTL30020 data and the products it mixes with.
Mixing matrix
- S30Thinner% by weight: 20–30 (typ. [object Object]) %catalog
Standard dilution to spray viscosity. S30 is a fast thinner.
Thinner does not take part in UV cure but must flash off fully before the lamps.
- S31Thinner% by weight: 20–30 %recommended
Hot shop (above ~25 °C) or large flat panels where S30 gives dry spray and poor flow.
Slower evaporation — lengthen the pre-dry before the lamps.
- S11Thinner% by weight: 20 %schedule
Official 'mouldings and baguette (UV)' schedule, written for VTL30040 at 150 g/m²; not stated for VTL30020 itself.
Conflict: the thinner table lists S11 for polyester gloss lacquers. For VTL30020 prefer S30 per the catalog.
| Role | Material | % by weight | % by volume | When |
|---|---|---|---|---|
| Thinner | S30 | 20–30 (typ. [object Object]) %catalog | — | Standard dilution to spray viscosity. S30 is a fast thinner.Thinner does not take part in UV cure but must flash off fully before the lamps. |
| Thinner | S31 | 20–30 %recommended | — | Hot shop (above ~25 °C) or large flat panels where S30 gives dry spray and poor flow.Slower evaporation — lengthen the pre-dry before the lamps. |
| Thinner | S11 | 20 %schedule | — | Official 'mouldings and baguette (UV)' schedule, written for VTL30040 at 150 g/m²; not stated for VTL30020 itself.Conflict: the thinner table lists S11 for polyester gloss lacquers. For VTL30020 prefer S30 per the catalog. |
Percentages are per 100 parts of component A.
Characteristics
- Solids
- 44–46 %catalog
- Gloss
- 20 GUofficial
- Chemical resistance
- physical-chemical resistance (site); excellent physical-chemical properties (catalog)official
- Scratch resistance
- scratch- and rub-resistantcatalog
- Flow
- excellent flow-out, levels well in thin filmsofficial
- Clarity
- high clarityofficial
- Pot life
- n/a — single-pack UV, no hardenerrecommended
- Viscosity
- 16–22 (ready to spray) srecommended
- Drying · Mechanism
- УФ-отверждение; мгновенное отверждение под УФ-лампамиcatalog
- Drying · Flash-off
- предварительная сушка 30–35 °C, 5–10 мин перед УФ-лампойschedule
- Drying · UV cure
- 80–120 Вт (3 лампы), 10 м/минschedule
- Drying · Sand or stack
- immediately after UV cure, once cooled to room temprecommended
- Drying · Conditions
- 30–35 °C pre-dry 5–10 min; UV 80–120 W lamps ×3 at 10 m/min (schedule gives 'Вт', no per-cm unit)
Colours
- VTL30020 · clear
Application
HVLP
- Consumption
- 110–130 g/m²official
- Nozzle
- 1.3–1.5 (typ. 1.4) mmrecommended
- Pressure · air · Inlet pressure, min
- 2
- Pressure · air · Inlet pressure, max
- 2.5
- Pressure · air · at the cap, max
- 0.7
- Pressure · air · Unit
- bar
- Pressure · air · Why ru
- Типичное давление на входе HVLP-краскопульта 2,0–2,5 бар (≤0,7 бар на головке) для жидких прозрачных лаков; проверяйте при нажатом курке.
- Spray viscosity
- 16–22 s DIN4recommended
- Wet film
- 110–135 µmrecommended
- Coats
- 1recommended
- Flash-off
- 30–35 °C, 5–10 мин до УФ-лампыschedule
- Recoat
- after full UV cure only after sanding P320–P400recommended
- Sanding between coats
- primer P240–P320 before topcoat; P320–P400 scuff if recoating cured lacquerrecommended
- Gun distance
- 15–20recommended
Matt lacquer: stir before use (matting agent settles), lay one even wet coat with consistent 50 % overlap or the sheen will be patchy.
Conventional spray
- Consumption
- 110–130 g/m²official
- Nozzle
- 1.4–1.6 mmrecommended
- Pressure · air
- 3–4 barrecommended
- Spray viscosity
- 16–20 s DIN4recommended
Universal method per the methods page but only ~40 % transfer — airmix/electrostatic is better on UV lines.
Airmix (air-assisted airless)
- Consumption
- 110–130 g/m²official
- Nozzle
- 0.23–0.28 mmrecommended
- Pressure · fluid
- 15–80 (typ. [object Object]) barrecommended
- Pressure · air
- 1–2 barofficial
- Spray viscosity
- 20–28 s DIN4recommended
Preferred production method for the topcoat.
Electrostatic
- Applicable
- yesrecommended
Airless
- Applicable
- norecommended
Roller coater (UV)
- Applicable
- norecommended
Process and compatibility
- Substrate preparation
- Wood/MDF sanded, stained if needed, UV primer applied and cured, sanded P240–P320, de-dusted.recommended
- Sanding
- шлифование грунта щётками К120, К150 перед лаком (схема погонажа, для VTL30040)schedule
- Temperature and humidity
- spray 18–25 °C, RH 40–70 %; pre-dry 30–35 °Crecommended
- Don'ts
- Do not send to the UV lamps without a pre-dry — trapped solvent causes bubbles, haze and poor adhesion
- Do not add hardeners — single-pack material
- Keep out of daylight/UV light in open containers
- Do not recoat a cured film without sanding
Storage
- Storage temperature
- 5–25 °C, dark, closedrecommended
Safety: Contains solvents — flammable; spray only in an extracted booth with an A-type organic-vapour respirator. Uncured acrylates are skin sensitisers: nitrile gloves and goggles. Shield eyes/skin from UV lamp radiation.
Sources
Value tags: “official”, “dealer”, “catalog”, “schedule” are Technocolor data; “workshop” is from our own datasheets; “recommended” is our engineering estimate (hover to see the reasoning).
- official page: name, properties (flow, clarity, chem resistance), spray 110–130 g/m²
- mouldings UV schedule: VTL30040 100 % + S11 20 %, 150 g/m², pre-dry 30–35 °C 5–10 min, UV 80–120 W ×3 at 10 m/min
- anegri panels UV schedule: sprayed VTL30100 pre-dry 30–35 °C TL03/05 5 min, UV ×3 at 10 m/min; sanding P240–P320
- methods: spray, airmix (≤20 bar fluid, 1–2 bar air), electrostatic, roller needs 98–100 % solids
- dealer search: no result
Not covered by the sources
- Viscosity of part A (no official/dealer/TDS value)
- Density
- Exact UV dose (mJ/cm²)/lamp type and exact flash-off time for VTL30020 itself (only sibling schedules)
- Shelf life and packaging
- Manufacturer nozzle/pressure data (all derived)
- Thinner basis (by weight vs volume) not stated in catalog; no % by volume
- Dealer page: t-colormarket.ru search returns no product for VTL30020 or VTL300 (re-checked 2026-10-05); woodonline.ru returns 0 results; lakokraska31/ndom31 show no product
- No ТДС/SDS PDF found (web search budget exhausted in this run)
- Conflict: mouldings schedule thins sibling VTL30040 with S11 (a polyester thinner per the thinner table) while catalog gives S30
- Airmix fluid pressure: official methods page says ≤20 bar, common equipment practice is 40–80 bar — no product-specific value