VTS40041
VTS40041 Clear UV-cure primer for vacuum coating, furniture (catalog: 100 %-solids clear UV primer)
Mix calculator
Ratio 100 : 0.0
| Component | Weigh out |
|---|---|
| VTS40041part A | 500 g |
| VTL10000Thinner | 0.0 g |
| Total | 500 g |
Covers roughly 5.56 m² at 90 g/m².
Pot life of the mix: n/a — single-component UV-cure, no hardener; stable until exposed to UV/daylight.
Ask about VTS40041
Answers are based on the VTS40041 data and the products it mixes with.
Mixing matrix
- VTL10000Thinner% by weight: 0–10 %catalog
Only if the primer is too heavy for the gun/vacuum head at the current temperature; warm the material first.
VTL10000 is a UV-reactive diluent that cures into the film (solids stay 100 %). Don't add ordinary solvents (S30/S31/S11): there's no flash-off before the lamp, so solvent gets trapped. Over 10 % costs hardness and sandability.
- Thinner% by weight: 0 %schedule
Moulding and picture-frame UV finish — per official schedule
Schedule uses the primer neat at 100 g/m².
| Role | Material | % by weight | % by volume | When |
|---|---|---|---|---|
| Thinner | VTL10000 | 0–10 %catalog | — | Only if the primer is too heavy for the gun/vacuum head at the current temperature; warm the material first.VTL10000 is a UV-reactive diluent that cures into the film (solids stay 100 %). Don't add ordinary solvents (S30/S31/S11): there's no flash-off before the lamp, so solvent gets trapped. Over 10 % costs hardness and sandability. |
| Thinner | 0 %schedule | — | Moulding and picture-frame UV finish — per official scheduleSchedule uses the primer neat at 100 g/m². |
Percentages are per 100 parts of component A.
Characteristics
- Solids
- 100official
- Viscosity
- approx. 40–80 s DIN4 at 20 °C (estimate, not published) srecommended
- Pot life
- n/a — single-component UV-cure, no hardener; stable until exposed to UV/daylightrecommended
- Drying · Flash-off (min)
- 0catalog
- Drying · Cure
- UV lamp cure at 30 m/min line speed (moulding schedule, 100 g/m²)schedule
- Drying · Sand or stack
- 0 hrecommended
- Drying · Conditions
- UV lamp; shop 18–25 °C
- Thixotropy
- norecommended
Colours
- clear · clear
Application
Vacuum coater
- Consumption
- 80–100 g/m² (official/catalog); 100 g/m² in moulding schedule g/m²official
- Wet film
- 70–90 µmrecommended
- Coats
- 1 coat → UV cure → brush sand K120/K150 → topcoatschedule
- Flash-off
- 0catalog
- Sanding between coats
- Щётки шлифовальные K120, K150 после УФ-отвержденияschedule
Airmix (air-assisted airless)
- Nozzle
- 0.28–0.33 mmrecommended
- Pressure · fluid
- 12–20 barrecommended
- Pressure · air
- 1–2 barrecommended
- Spray viscosity
- material warmed to 35–45 °C; VTL10000 up to 10 % only if still too heavyrecommended
- Consumption
- 80–100 g/m²official
- Coats
- 1 full wet coat (80–100 g/m²), UV cure, sandrecommended
- Flash-off
- 0catalog
- Recoat
- immediately after UV cure and sandingrecommended
- Sanding between coats
- P240–P320 by hand/orbital, or K120/K150 brushes on profilesrecommended
Use it for profiles and parts where you need a cleaner fan. With 100 % solids, the material has to be warmed. For primers on large flat parts the methods page recommends airless. The film goes straight under the lamp with no wait. recommended
Airless
- Nozzle
- 0.28–0.38 mmrecommended
- Pressure · fluid
- 120–180 barrecommended
- Consumption
- 80–100 g/m²official
For large flat parts. Coarser fan edges than airmix. recommended
HVLP
- Nozzle
- 1.8–2.2 mmrecommended
- Pressure · air
- 2–2.5 barrecommended
- Pressure · fluid
- 0.8–1.5 barrecommended
- Consumption
- 80–100 g/m²official
Samples and repairs only — HVLP struggles with solvent-free material, expect some orange peel, which sands out. recommended
Process and compatibility
- Substrate preparation
- Шлифование щётками K60, K80; при необходимости — краситель CTU 100% / CFS1 150% / S12 500%, 80 г/м², сушка 25–30 °C 5 минschedule
- Sanding
- K120, K150 brushes after UV cureschedule
- Temperature and humidity
- Shop 18–25 °C; material kept at constant temperature (warmed for spray); away from daylightrecommended
Storage
Safety: No manufacturer data. UV materials contain acrylate monomers (skin sensitisers): nitrile gloves, goggles, avoid skin contact; shield eyes and skin from UV lamps. When spraying use an A2P2 respirator.
Used in finishing systems
Sources
Value tags: “official”, “dealer”, “catalog”, “schedule” are Technocolor data; “workshop” is from our own datasheets; “recommended” is our engineering estimate (hover to see the reasoning).
- name, properties (100% solids, high reactivity, sands well, stable), spray 80–100 g/m²
- moulding/frame UV schedule: stain → VTS40041 100 g/m² → UV 30 m/min → K120/K150 → VTL30040
- application methods: airless up to 200 bar, ideal for primers on large flat surfaces; airmix up to 20 bar fluid / 1–2 bar air, better for finish coats (does not cover vacuum coating)
- dealer search — no product
Not covered by the sources
- No dealer page: t-colormarket.ru, woodonline.ru, lakokraska31.ru, ndom31.ru searched — not listed (dealer shop has no UV category)
- No TDS/SDS PDF found (web search budget exhausted in this run)
- Viscosity, density, gloss, hardness, chemical resistance not published (viscosity given only as a derived estimate)
- UV cure dose (mJ/cm²) / lamp type & power for this primer not published — only 30 m/min line speed in the schedule
- Manufacturer spray settings (nozzle, pressure, material temperature) not published — all derived
- Shelf life, storage temperature, packaging unknown
- Official page says application 'Распыление' while the name says vacuum application; catalog says spray, vacuum also possible — recorded both
- Vacuum-coater application isn't on the official methods page. Vacuum settings are general practice only.