VPS60011
VPS60011 white UV-curing primer
White pigmented UV-curing primer for spray application. Per Technocolor it sands easily and has good adhesion. Used as the base coat under white/coloured UV or PU topcoats on lines equipped with UV curing.
- Priming MDF fronts and panels under white/coloured enamel on UV-cure lines
- Priming profiled parts where roller coating is not possible (spray application)
Single-component product: no mixing needed — use as supplied (see application below).
Ask about VPS60011
Answers are based on the VPS60011 data and the products it mixes with.
Mixing matrix
- Hardener
No hardener - cures under UV light. The official page lists none.
Only to trim to spray viscosity; S31 as the default, S30/S13 when you need the solvent gone faster before the lamp.
No published ratio for VPS60011 - confirm with Technocolor. In the official UV moulding schedule the sprayed UV lacquer VTL30040 is thinned 20 % with S11 - an analogy, not VPS60011 data. If the primer is 100 % solids (solvent-free) thinning may not be allowed at all.
| Role | Material | % by weight | % by volume | When |
|---|---|---|---|---|
| Hardener | — | — | No hardener - cures under UV light. The official page lists none. | |
| Thinner | S30 / S31 / S13 | — | — | Only to trim to spray viscosity; S31 as the default, S30/S13 when you need the solvent gone faster before the lamp.No published ratio for VPS60011 - confirm with Technocolor. In the official UV moulding schedule the sprayed UV lacquer VTL30040 is thinned 20 % with S11 - an analogy, not VPS60011 data. If the primer is 100 % solids (solvent-free) thinning may not be allowed at all. |
Percentages are per 100 parts of component A.
Characteristics
- Solids
- not published; spray UV primers typically 60-100 %recommended
- Drying · Cure
- UV cure: guide 80-120 W, 3 lamps, 10 m/min (as in Technocolor schedules, which state plain 'W', not W/cm); for a white pigmented coat use a gallium-doped lamp plus mercuryrecommended
- Drying · Sand or stack
- immediately after leaving the UV tunnel and coolingrecommended
- Drying · Conditions
- line conditions
- Pot life
- 1-pack, unlimited while kept from lightrecommended
- Thixotropy
- unknownrecommended
Colours
- VPS60011 · white
Application
Conventional spray
Spraying is the only officially listed method.
HVLP
Gun distance 15-20 cm, 50 % overlap. Always flash off before the lamp.
Airmix (air-assisted airless)
- Pressure · air
- 1–2 barofficial
Preferred on a line - high transfer efficiency, even film.
Airless
Process and compatibility
- Substrate preparation
- sand MDF/wood P150-P220, de-dustrecommended
- Sanding
- after UV cure P240-P320recommended
- Temperature and humidity
- material and part 18-25 °C; flash-off 30-35 °Crecommended
- Don'ts
- Do not send an un-flashed coat into the UV lamp - blisters and poor intercoat adhesion
- Do not leave the can open in daylight
- Do not lay more than ~150 g/m² per pass - a pigmented coat will not through-cure
Storage
Safety: Contains acrylate monomers (typical of UV materials) - skin sensitiser: nitrile gloves, eye protection, respirator when spraying. Shield eyes/skin from UV lamp radiation.
Sources
Value tags: “official”, “dealer”, “catalog”, “schedule” are Technocolor data; “workshop” is from our own datasheets; “recommended” is our engineering estimate (hover to see the reasoning).
- Official page: properties (easy sanding, good adhesion), spray 120-150 g/m²
- Methods: airmix/airless pressures; roller UV = 98-100 % solids
- UV schedule: sanding grits, lamp 80-120 W x3, 10 m/min (by analogy)
- UV schedule: sprayed UV lacquer VTL30040 + S11 20 %, 150 g/m², pre-dry 30-35 °C 5-10 min (by analogy)
Not covered by the sources
- Dealer page: VPS60011 not found on t-colormarket.ru, woodonline.ru (search returned nothing)
- No TDS PDF found (web search budget exhausted; direct dealer/bing probes found nothing)
- Not listed in the scanned 2025-2026 catalog transcripts or in any official finishing schedule
- Solids %, viscosity, density, application viscosity - unknown
- Thinner ratio (or whether thinning is allowed) - unknown
- Required UV dose (mJ/cm²), lamp type, belt speed - unknown (only generic schedule values)
- Compatible topcoats (goes_under) - not stated officially
- Shelf life, storage temperature, packaging - unknown
- Hardness, elasticity, chemical resistance, lightfastness - unknown
- Dealer search t-colormarket.ru/search/?q=VPS60011 re-checked 2026-10-05: no product