VTS60019
VTS60019 clear high-solids UV-curing spray primer
Clear high-solids (87 %, catalog) UV-curing primer for spray application. Per Technocolor it has good adhesion, stays clear and sands easily by hand; for finishing articles of various wood species by spraying. Use on profiles, fronts and shaped parts where roller coating is not possible is our inference from the spray method, not stated by Technocolor.
- Priming solid wood and veneer of any species under clear UV spray lacquers
- Priming profiled parts and fronts where roller coating is not possible
- Higher-build alternative to VTS30006 (38 % solids) when more film per pass is needed
Mix calculator
Ratio 100 : 25.0
| Component | Weigh out |
|---|---|
| VTS60019part A | 400 g |
| S30Thinner | 100 g |
| Total | 500 g |
Pot life of the mix: 1-pack; unlimited while kept away from light.
Ask about VTS60019
Answers are based on the VTS60019 data and the products it mixes with.
Mixing matrix
- Hardener
No hardener - cures under UV light. Neither the official page nor the catalog lists one.
- S30Thinner% by weight: 20–30 (typ. 25) %catalog
Always, to bring it to spray viscosity. S30 is a fast thinner and leaves quickly during the pre-lamp flash-off.
20 % for build on flat work; 30 % for verticals, profiles and smaller nozzles. Do not go past 30 %: longer flash-off and blistering risk under the lamp.
- S31Thinner
Only for a hot booth / dry spray with S30 - extend flash-off to 10+ min.
Not specified by Technocolor for VTS60019 - test on a sample first.
| Role | Material | % by weight | % by volume | When |
|---|---|---|---|---|
| Hardener | — | — | No hardener - cures under UV light. Neither the official page nor the catalog lists one. | |
| Thinner | S30 | 20–30 (typ. 25) %catalog | — | Always, to bring it to spray viscosity. S30 is a fast thinner and leaves quickly during the pre-lamp flash-off.20 % for build on flat work; 30 % for verticals, profiles and smaller nozzles. Do not go past 30 %: longer flash-off and blistering risk under the lamp. |
| Thinner | S31 | — | — | Only for a hot booth / dry spray with S30 - extend flash-off to 10+ min.Not specified by Technocolor for VTS60019 - test on a sample first. |
Percentages are per 100 parts of component A.
Characteristics
- Solids
- 87 %catalog
- Viscosity
- not published; working spray viscosity roughly 20-30 s DIN4 after 20-30 % S30 srecommended
- Pot life
- 1-pack; unlimited while kept away from lightrecommended
- Drying · Cure
- UV cure: guide 80-120 W (as printed in the schedule; probably W/cm) mercury lamps x3 at 10 m/minrecommended
- Drying · Sand or stack
- right after leaving the UV tunnel and coolingrecommended
- Drying · Conditions
- line conditions
- Thixotropy
- unknownrecommended
Colours
- VTS60019 · clear
Application
Conventional spray
Spraying is the only officially listed method.
HVLP
- Sanding between coats
- P280-P320 after UV curerecommended
Distance 15-20 cm, 50-75 % overlap, fan fully open. Always flash off before the lamp.
Airmix (air-assisted airless)
- Pressure · air
- 1–2 barofficial
Best option on a line: high transfer, even film, less solvent overspray.
Airless
Process and compatibility
- Substrate preparation
- sand wood/veneer P150-P180 (P220 for close grain), de-dust; stain and dry first if neededrecommended
- Sanding
- after UV cure P280-P320 by handrecommended
- Temperature and humidity
- material and part 18-25 °C, RH ≤ 70 %; flash-off 30-35 °Crecommended
- Don'ts
- Do not send an un-flashed coat into the UV lamp - blisters, soft film, poor intercoat adhesion
- Do not thin past 30 % S30
- Do not leave the can or gun cup open in daylight
- Do not lay more than ~120 g/m² per pass
Storage
Safety: Contains acrylate monomers (typical of UV materials) plus S30 solvent once thinned - skin sensitiser, flammable: nitrile gloves, eye protection, organic-vapour respirator when spraying, ventilation. Shield eyes/skin from UV lamp radiation.
Sources
Value tags: “official”, “dealer”, “catalog”, “schedule” are Technocolor data; “workshop” is from our own datasheets; “recommended” is our engineering estimate (hover to see the reasoning).
- Official page: properties (sands well by hand, clear, good adhesion), spray 100-120 g/m²
- Methods: airmix/airless pressures
- UV moulding schedule: pre-dry of sprayed UV lacquer (VTL30040 + 20 % S11) 30-35 °C 5-10 min, lamp '80-120 Вт (3шт)', 10 m/min (by analogy)
- UV panel schedule: sanding P150-P220 before, P240-P320 after primer; pre-dry 30-35 °C 5 min (by analogy)
- Dealer search - no result
- UV parquet schedule: P240-P320 after primer; lamp 80-120 W x3, 10 m/min (by analogy)
Not covered by the sources
- Dealer: VTS60019 not sold on t-colormarket.ru (search returns no product; UV range absent there)
- No TDS PDF found (web search budget exhausted again in verification, 2026-10-05)
- Not used in any official finishing schedule
- Viscosity of part A, density - unknown
- Thinner basis (weight vs volume) not stated in catalog; % by volume unknown
- UV dose (mJ/cm²), lamp type, belt speed - only generic schedule values
- Compatible topcoats (goes_under) - not officially stated
- Shelf life, storage temperature, packaging - unknown
- Hardness, elasticity, chemical resistance, lightfastness - unknown