PTL01
PTL01 Fire-retardant polyurethane lacquer, 20 gloss
Two-pack fire-retardant polyurethane topcoat, 20 gloss (satin-matt). When heated, the fire-retardant components decompose and give off non-combustible gas that blocks oxygen and slows fire spread. Fast drying (including to packing), excellent flow-out, pleasant soft feel. Used as the topcoat over clear fire-retardant primer PTS01; together they form a Group II fire-protection system to GOST R 53292-2009 (cl. 6.1). Interior use only.
- Protecting and improving fire resistance of timber structures indoors
- Clear topcoat in the PTS01 + PTL01 fire-retardant system (Group II, GOST R 53292-2009)
- Wall panelling, cladding, doors and furniture in public interiors where certified fire protection is required
Mix calculator
Ask about PTL01
Answers are based on the PTL01 data and the products it mixes with.
Mixing matrix
- PC25Hardener% by weight: 50 %dealer% by volume: 50 %dealer
Standard hardener per the dealer card
Fixed ratio — do not tweak it; the fire rating is certified on this formulation.
- PC20Hardener% by weight: 50 %catalog% by volume: 50 %recommended
Catalogue and leaflet list PC20 as the hardener; dealer lists it as an alternative: more flexible film, slower drying
Sources disagree: catalogue/leaflet say PC20, dealer says PC25 (PC20 as alternative). Both at 50 %.
- PC60Hardener% by weight: 50 %recommended% by volume: 50 %recommended
When non-yellowing matters (pale timber, whitewashed tones)
Swap sourced from the dealer; percentage taken by analogy with PC25.
- S50Thinner% by weight: 20–30 (typ. 25) %dealer% by volume: 20–30 (typ. 25) %dealer
Normal conditions, verticals
Catalogue and leaflet give the same 20–30 % (basis not stated). Dealer: 20–30 % both by weight and by volume. 'default 25' is the mid-point (derived).
- % by weight: 20–30 (typ. 25) %recommended% by volume: 20–30 (typ. 25) %recommended
Hot weather — for better flow-out (dealer); in practice above ~25 °C (workshop notes)
S80 is slow: more dust pick-up and sag risk on verticals. Does not change cure time.
| Role | Material | % by weight | % by volume | When |
|---|---|---|---|---|
| Hardener | PC25 | 50 %dealer | 50 %dealer | Standard hardener per the dealer cardFixed ratio — do not tweak it; the fire rating is certified on this formulation. |
| Hardener | PC20 | 50 %catalog | 50 %recommended | Catalogue and leaflet list PC20 as the hardener; dealer lists it as an alternative: more flexible film, slower dryingSources disagree: catalogue/leaflet say PC20, dealer says PC25 (PC20 as alternative). Both at 50 %. |
| Hardener | PC60 | 50 %recommended | 50 %recommended | When non-yellowing matters (pale timber, whitewashed tones)Swap sourced from the dealer; percentage taken by analogy with PC25. |
| Thinner | S50 | 20–30 (typ. 25) %dealer | 20–30 (typ. 25) %dealer | Normal conditions, verticalsCatalogue and leaflet give the same 20–30 % (basis not stated). Dealer: 20–30 % both by weight and by volume. 'default 25' is the mid-point (derived). |
| Thinner | S70 / S80 | 20–30 (typ. 25) %recommended | 20–30 (typ. 25) %recommended | Hot weather — for better flow-out (dealer); in practice above ~25 °C (workshop notes)S80 is slow: more dust pick-up and sag risk on verticals. Does not change cure time. |
Percentages are per 100 parts of component A.
Characteristics
- Solids
- 44 ± 1 %dealer
- Viscosity
- 65 ± 5 sdealer
- Gloss
- 20 ± 3 GU 60°dealer
- Pot life
- 4 hdealer
- Drying · Touch-dry
- 30 mindealer
- Drying · Full cure
- 8 hdealer
- Drying · Sand or stack
- ≥ 8 h (pack/stack after full dry; leave 24 h before heavy handling)recommended
- Drying · Conditions
- 20 °C
- Fire protection
- II группа огнезащитной эффективности, ГОСТ Р 53292-2009 (п. 6.1) — in system with PTS01dealer
- Lightfastness
- Moderate with PC25/PC20; use PC60 when yellowing mattersrecommended
- Chemical resistance
- высокая физико-химическая стойкость (range claim)catalog
- Elasticity
- PC20 instead of PC25 increases flexibility (and slows drying)dealer
- Thixotropy
- norecommended
Application
HVLP
- Consumption
- 150 g/m² per coatdealer
- Coats
- 1 coat PTL01 over PTS01 at 150 g/m² each (a second PTL01 coat only if build is needed)recommended
- Recoat
- Over PTS01: after it has dried ≥ 4 h and been sanded (overnight is safer); PTL01 over PTL01: 4–8 h after sanding, or within 24 h without full cure lock-outrecommended
- Sanding between coats
- Sand PTS01 with P320–P400 before PTL01; denib PTL01 between coats with P400–P600. Don't polish the 20-gloss final coat.recommended
Manufacturer lists spraying only (dealer, catalogue) — no brush/roller. Lay it on at the full 150 g/m²: under-building the film costs you the fire rating.
Conventional spray
- Consumption
- 150 g/m²dealer
Methods page: transfer efficiency up to ~40 %, so gun usage will be well above the 150 g/m² that lands on the part.
Airmix (air-assisted airless)
- Consumption
- 150 g/m²dealer
Methods page: airmix fluid pressure 'up to 20 bar', atomising air 1–2 bar.
Airless
- Consumption
- 150 g/m²dealer
Methods page: airless up to 200 bar, transfer up to 90 %, ideal for priming large flats. For the topcoat airmix usually gives a cleaner finish with less sag/orange peel.
Process and compatibility
- Substrate preparation
- Clean dry timber (8–12 % MC), sanded P150–P180, dust removed. No oils, waxes or silicone.recommended
- Goes over
- PTS01
- Don'ts
- Don't use outdoors — interior-only material (dealer, catalogue)
- Don't change the 50 % hardener ratio — the fire rating is certified on the formulation
- Don't skimp on film: under 150 g/m² the system may not reach Group II
- Don't use the mix past its 4 h pot life
- Don't polish the 20-gloss finish — you'll get shiny patches
Storage
- Packaging
- 1 л, 5 л, 25 лdealer
- Storage temperature
- +5…+25 °C, sealed, away from heatrecommended
Safety: Flammable solvent-borne material (the wet lacquer burns — the fire rating applies to the cured film only); contains isocyanates once mixed. Spray in a booth, wear an A2P2 organic-vapour respirator (or air-fed), nitrile gloves and eye protection. Keep away from flames and sparks.
Used in finishing systems
Mixed into
Sources
Value tags: “official”, “dealer”, “catalog”, “schedule” are Technocolor data; “workshop” is from our own datasheets; “recommended” is our engineering estimate (hover to see the reasoning).
- Dealer card: properties, scope (Group II GOST R 53292-2009), PC25 50/50 %, S50 20–30 %, hardener alternatives, gloss 20±3, solids 44±1 %, viscosity 65±5 s VZ-4, pot life 4 h, touch 30 min, full 8 h, packs 1/5/25 l
- Partner primer PTS01 dealer card (PC25 50/50 %, S50 20–30 % w / 25–35 % v, solids 47±1 %, 60±5 s VZ-4, pot life 3–4 h, touch 30 min, full 8 h)
- Application methods page (spray methods; air spray transfer up to 40 %; airless up to 200 bar / 90 % transfer; airmix fluid up to 20 bar, air 1–2 bar)
Not covered by the sources
- No official t-color.ru product page
- No real TDS / SDS PDF found
- Density not published
- Shelf life not published
- Hardness, abrasion and chemical-resistance numbers not published
- Dust-free time not published (only touch 30 min)
- Pot life with PC20/PC60 not published
- Not in any official finishing schedule (information/technology)
- All nozzle/pressure/viscosity application data are derived — no manufacturer spray settings exist
- Fire-rating test certificate number not seen (leaflet says certificates are supplied on request)
- Hardener % by volume for PC20/PC60 and thinner % by volume for S70/S80 not published (derived from PC25/S50 dealer ratios)
- Catalogue/leaflet ratios (PC20 50 %, S50 20–30 %) do not state weight vs volume
- Hardener solids not published — dry-film estimate is approximate
- Official methods page airmix fluid pressure ('до 20 bar') is lower than the derived 40–80 bar working window