VTL30010
UV-curing spray lacquer for furniture, 10 gloss (dead matt), clear
Single-pack, solvent-borne clear UV-curing spray lacquer, dead-matt 10 gloss. Flows out very well, high clarity, scratch- and scuff-resistant, good chemical/physical resistance. 44–46 % solids, so it needs a solvent flash-off before going under the UV lamps. Good choice for cabinet doors, interior doors and bathroom furniture.
- Dead-matt (10 gloss) clear topcoat on cabinet fronts
- Interior doors
- Bathroom furniture
- Carcase parts, veneered and solid-wood parts on spray UV lines
Mix calculator
Ratio 100 : 25.0
| Component | Weigh out |
|---|---|
| VTL30010part A | 400 g |
| S30Thinner | 100 g |
| Total | 500 g |
Covers roughly 4.17 m² at 120 g/m².
Pot life of the mix: not applicable — 1K, no hardener.
Ask about VTL30010
Answers are based on the VTL30010 data and the products it mixes with.
Mixing matrix
- S30Thinner% by weight: 20–30 (typ. [object Object]) %catalog% by volume: 23–34 (typ. 28) %recommended
Standard spray thinner, fast evaporation.
S30 = fast thinner for PU, acrylic, polyester and UV materials (catalog thinner table).
- S31Thinner% by weight: 20–30 %recommended
Hot shop (above ~25 °C), large flat panels, dry spray with S30.
Lengthens the flash before UV — don't cut the flash time.
- S11Thinner% by weight: 20 %recommended
As in the official moulding/frame schedule (given for VTL30040).
Analogy only; catalog thinner S30 preferred.
| Role | Material | % by weight | % by volume | When |
|---|---|---|---|---|
| Thinner | S30 | 20–30 (typ. [object Object]) %catalog | 23–34 (typ. 28) %recommended | Standard spray thinner, fast evaporation.S30 = fast thinner for PU, acrylic, polyester and UV materials (catalog thinner table). |
| Thinner | S31 | 20–30 %recommended | — | Hot shop (above ~25 °C), large flat panels, dry spray with S30.Lengthens the flash before UV — don't cut the flash time. |
| Thinner | S11 | 20 %recommended | — | As in the official moulding/frame schedule (given for VTL30040).Analogy only; catalog thinner S30 preferred. |
Percentages are per 100 parts of component A.
Characteristics
- Solids
- 44–46 %catalog
- Gloss
- 10 GU (60°)official
- Viscosity
- as supplied: n/a; spray 18–22 srecommended
- Flow
- excellent flow-outofficial
- Clarity
- high clarityofficial
- Chemical resistance
- physical-chemical resistanceofficial
- Scratch resistance
- scratch and scuff resistantcatalog
- Pot life
- not applicable — 1K, no hardenerrecommended
- Drying · Mechanism
- УФ-отверждение под лампами высокого давления; мгновенное отверждение после испарения разбавителяcatalog
- Drying · UV cure
- 80–120 W (as published: '80-120 Вт'; per-cm lamp rating implied) × 3 lamps, 10 m/minrecommended
- Drying · Stack or sand
- immediately after cooling (~10–15 min)recommended
- Drying · Conditions
- see process.temperature_rh
Colours
- VTL30010 · clear
Application
HVLP
- Consumption
- 110–130 g/m²official
- Nozzle
- 1.3–1.5 (typ. 1.4) mmrecommended
- Pressure · air · Inlet pressure
- 2–2.5
- Pressure · air · at the cap, max
- 0.7
- Pressure · air · Unit
- bar
- Pressure · air · Why ru
- Типично для HVLP: 2,0–2,5 бар на входе пистолета (курок нажат) → ≤0,7 бар на воздушной головке.
- Spray viscosity
- 18–22 srecommended
- Wet film
- 110–135 µmrecommended
- Coats
- 1–2recommended
- Flash-off
- 5–10 minrecommended
- Recoat
- after UV cure + cooling + scuff sandingrecommended
- Sanding between coats
- P320–P400 between cured coats; don't touch the final coatrecommended
Stir thoroughly before use — matting agent settles. Keep the can away from daylight and the UV lamps. recommended
Conventional spray
- Consumption
- 110–130 g/m²official
- Nozzle
- 1.4–1.6 mmrecommended
- Pressure · air
- 2.5–3.5 barrecommended
- Spray viscosity
- 18–22 srecommended
Conventional air spray: up to 40 % transfer efficiency (methods page). official
Airmix (air-assisted airless)
- Consumption
- 110–130 g/m²official
- Nozzle
- 09–11 thou (0.23–0.28 mm), fan 20–40°recommended
- Pressure · fluid
- start ≤20 bar per methods page; typical 30–60 barrecommended
- Pressure · air
- 1-2 barofficial
- Spray viscosity
- 20–25 srecommended
Airmix is better suited to topcoats than airless (methods page). official
Electrostatic
- Applicable
- yesrecommended
Airless
- Applicable
- norecommended
Roller coater (UV)
- Applicable
- norecommended
Process and compatibility
- Substrate preparation
- Wood/veneer P150–P220 → UV primer → cure → sand P240–P320 → de-dust.recommended
- Sanding
- before the UV topcoatschedule
- Temperature and humidity
- 18–25 °C, RH 50–70 %recommended
- Don'ts
- Don't send it under the UV lamps without a solvent flash-off
- Don't sand or polish the final 10-gloss coat
- Don't leave it in daylight — it will start to cure
- Not for roller coaters — spray grade
- Don't lay more than ~130 g/m² per pass — patchy matt, trapped solvent
Storage
- Storage temperature
- 5–25 °C, dark, closedrecommended
Safety: Contains solvents (flammable) and uncured acrylates (skin sensitisers): spray booth extraction, nitrile gloves, goggles, A-filter respirator when spraying. Shield eyes/skin from UV lamp radiation. Cure leftovers in daylight before disposal.
Sources
Value tags: “official”, “dealer”, “catalog”, “schedule” are Technocolor data; “workshop” is from our own datasheets; “recommended” is our engineering estimate (hover to see the reasoning).
- official page: properties (flow, clarity, physical-chemical resistance), spray 110–130 g/m², 10 gloss
- application methods: conventional ≤40 % transfer, airmix ≤20 bar fluid + 1–2 bar air, roller needs 98–100 % solids
- UV moulding schedule: sister VTL30040 + S11 20 %, 150 g/m², flash 30–35 °C 5–10 min, UV '80-120 Вт (3шт)', 10 m/min (used by analogy)
- UV anegri panel schedule: P240–P320 sanding before topcoat, VTL30100 flash 30–35 °C 5 min + UV 3 lamps
- dealer search: no result
Not covered by the sources
- Viscosity as supplied (no official/dealer/TDS value)
- Density
- Pot life after thinning / open time not published
- Manufacturer flash-off time and UV dose (mJ/cm²) for VTL30010 — only sister VTL30040 schedule exists
- Shelf life and packaging
- Hardness, elasticity, lightfastness numbers
- Dealer page: t-colormarket.ru has no UV category and returns nothing for VTL30010; lakokraska31/woodonline/ndom31 searches returned nothing
- No ТДС/SDS PDF found (web search budget exhausted in this run)
- Not used in any official finishing schedule (VTL30040/VTL30100 are)
- Not in the 2025–2026 scanned catalog transcripts
- Weight vs volume basis of the S30 20–30 % ratio not stated; volume % in file is a density-based conversion (derived)
- UV lamp unit in official schedules printed as 'Вт' (W) without per-cm; sister-product values only