Skip to content
Dugan Design
← All products
+ Add to shopping list
PolyurethaneEnamelGloss: 20 GU

PPL10 M

PPL10 M white PU enamel, matt (20 gloss)

Two-pack fast-drying white polyurethane enamel, matt (20 gloss). High solids (about 65 % on part A), excellent hiding power and good sag resistance. Cured with PC60 hardener, thinned with S50 (the catalogue also allows S70).

  • finishing MDF furniture fronts
  • finishing MDF panels
  • white matt topcoat over a PU primer

Mix calculator

g
Hardener40.0 %

PC60: 40.0 % — fixed by the datasheet

Thinner25.0 %

When: Default, normal evaporation; 18–25 °C, vertical work.

Ratio 100 : 40.0 : 25.0

ComponentWeigh out
PPL10 Mpart A303 g
PC60Hardener121 g
S50Thinner75.8 g
Total500 g

Covers roughly 3.33 m² at 150 g/m².

Pot life of the mix: 4.

Ask about PPL10 M

Answers are based on the PPL10 M data and the products it mixes with.

Questions and answers are stored to improve the assistant and prevent abuse; the question text is processed by Anthropic (USA). Privacy policy

Mixing matrix

  • PC60Hardener
    % by weight: 40 %official% by volume: 55 %official

    Fixed ratio: 40 % by weight (55 % by volume). Weigh it — too little gives a soft film, extra hardener does not speed up drying.

  • S50Thinner
    % by weight: 20–30 (typ. 25) %official% by volume: 30–45 %official

    Default, normal evaporation; 18–25 °C, vertical work.

    S50 is the universal thinner, medium evaporation (official page); catalogue p.19: for PU/acrylic primers, matt lacquers and enamels.

  • S70Thinner
    % by weight: 20–30 %catalog

    Hot shop (above ~25 °C) or large flat panels — slow thinner, longer open time for flow-out.

    Listed only in the 2025–26 catalogue (p.9), not on the product page; no volume % published. Catalogue p.19: S70 = slow evaporation, for deep-matt and high-gloss PU/acrylic materials. More sag and dust risk.

Percentages are per 100 parts of component A.

Characteristics

Solids
65 ± 1 %dealer
Viscosity
20 ± 3 sdealer
Density · Part A
1.3 g/mlrecommended
Density · Mixed
1.12 g/mlrecommended
Gloss
20 GUdealer
Pot life
4dealer
Drying · Touch-dry
30dealer
Drying · Full cure
8dealer
Drying · Dust-free
15–20 minrecommended
Drying · Sand or stack
8–16 hrecommended
Drying · Conditions
20 °C
Lightfastness
non-yellowing class hardener (PC60)catalog
Thixotropy
sag-resistant (стойкость к подтекам)dealer

Colours

  • white · white

Application

Conventional spray

Consumption
150official
Nozzle
1.8–2 mmrecommended
Pressure · air
3–4 barrecommended
Spray viscosity
22–28 s DIN4recommended
Wet film
120–140 µmrecommended
Coats
1–2 coatsrecommended
Flash-off
10–15 minrecommended
Recoat
8–24 hrecommended
Sanding between coats
P400–P500 denibrecommended

Mix part A thoroughly before catalysing (pigment and matting agent settle) — dealer instruction. Strain through 125–190 µm.

HVLP

Consumption
150official
Nozzle
1.8–2 mmrecommended
Pressure · air
2–2.5 barrecommended
Spray viscosity
22–28 s DIN4recommended
Gun distance
15–20 cmrecommended
Overlap
50–75 %recommended
Coats
1–2 coatsrecommended

Lay a full, even wet coat; dry spray at the fan edges shows as gloss striping on a 20-gloss enamel.

Airmix (air-assisted airless)

Nozzle
0.23–0.33 mmrecommended
Pressure · fluid
40–80 barrecommended
Pressure · air
1–2 barofficial
Spray viscosity
25–35 s DIN4recommended

The catalogue shows only the 'spray' (air gun) icon for PPL10; airmix is acceptable by general practice but not confirmed by Technocolor for this product. Methods page: airmix suits topcoats better than airless.

Airless

Nozzle
0.28–0.33 mmrecommended
Pressure · fluid
120–180 barrecommended

The official methods page recommends airless mainly for primers; for a finish enamel use airmix or air spray.

Process and compatibility

Substrate preparation
MDF: sand P180–P240, de-dust, apply white PU primer (2 coats on edges), sand primer P320–P400, de-dust, then enamel.recommended
Goes over
PPS20 / PPS50 / PPS50277
Sanding · Before
primer P320–P400recommended
Sanding · Between
P400–P500 denibrecommended
Sanding · Final
do not sand or polish the final matt coatrecommended
Temperature and humidity
18–25 °C, RH 50–70 %, material and parts at room temperaturerecommended
Don'ts
  • do not use after the 4 h pot life
  • do not change the PC60 ratio
  • do not thin with nitro thinners
  • do not apply over damp wood/MDF (>10–12 % moisture)
  • do not sand the final matt coat

Storage

Packaging
1,5,25 kgdealer

Safety: 2K PU system with organic solvents and an isocyanate hardener. Spray only in an extracted booth, wear an A2P2 respirator or air-fed mask, gloves and goggles. Flammable.

Mixed into

PC60

Sources

Value tags: “official”, “dealer”, “catalog”, “schedule” are Technocolor data; “workshop” is from our own datasheets; “recommended” is our engineering estimate (hover to see the reasoning).

Not covered by the sources
  • dust-free time not published (derived)
  • spray viscosity, nozzle and pressure not published (derived)
  • no real Technocolor TDS/SDS PDF found for PPL10 or PC60
  • shelf life and storage temperature not published
  • density not published (back-calculated from wt/vol ratios)
  • tintability (CGS/RAL) for PPL10 not stated
  • no official finishing schedule uses PPL10
  • solids conflict: 65 ± 1 % (dealer, web catalogue) vs 67 % (2025-26 catalogue)
  • S70 allowed only per 2025-26 catalogue; no S70 volume % published
  • hardness and chemical resistance not published; lightfastness only inferred from PC60's hardener class (catalogue p.19), no ΔE data
  • PC60 confirmed 'yellowing-resistant' class but not stated as fully aliphatic
  • airmix fluid pressure: official methods page says up to 20 bar, derived shop value 40–80 bar