ATL60180 M
ATL60180 M Clear acrylic converter for exterior use (20 gloss)
Clear two-pack solvent-borne acrylic (acrylic-PU, cured with the aliphatic isocyanate AC40) converter for exterior work — the base for tinting bright, saturated-colour enamels with CS pigment pastes. Highly elastic, weather- and lightfast, mechanically tough; non-yellowing, chemically resistant, high solids.
- Base for bright, saturated exterior enamels
- Timber houses, fences, window frames, gazebos and other exterior timber
- Exterior surfaces that take mechanical wear
Mix calculator
Ask about ATL60180 M
Answers are based on the ATL60180 M data and the products it mixes with.
Mixing matrix
- AC40Hardener% by weight: 40 %catalog
Always — this is a two-pack material.
Fixed 40 %, don't eyeball it: short hardener kills weather resistance. AC40 is aliphatic, the most non-yellowing hardener in the range (catalog p.19). The 2019 catalog prints "С40" — same AC40, old label/typo.
- S50Thinner% by weight: 20–30 (typ. 25) %catalog
Standard choice at 18–25 °C. S50 = medium evaporation, for PU/acrylic primers, matt lacquers and enamels (catalog p.19).
The 2019 catalog gives the same 20–30 % S50.
- S80Thinner% by weight: 20–30 %recommended
Above ~25 °C, large panels/cladding, dry air — to stop dry spray and orange peel.
Slower — more dust pick-up and sag risk on verticals. Doesn't change cure time. Not a Technocolor-listed option — test panel first.
- CS 10 / CS 20 / CS 21 / CS 22 / CS 23 / CS 30 / CS 40 / CS 50 / CS 51 / CS 53 / CS 60 / CS 70 / CS 80 / CS 90 / CS 91Additive
Tinting the converter into an enamel (RAL/NCS) to a SPECTRUM recipe.
CS pastes are the solvent-system (PU/acrylic) range per the SPECTRUM tinting leaflet. Add paste to part A and mix BEFORE the hardener. Technocolor publishes no max paste loading.
| Role | Material | % by weight | % by volume | When |
|---|---|---|---|---|
| Hardener | AC40 | 40 %catalog | — | Always — this is a two-pack material.Fixed 40 %, don't eyeball it: short hardener kills weather resistance. AC40 is aliphatic, the most non-yellowing hardener in the range (catalog p.19). The 2019 catalog prints "С40" — same AC40, old label/typo. |
| Thinner | S50 | 20–30 (typ. 25) %catalog | — | Standard choice at 18–25 °C. S50 = medium evaporation, for PU/acrylic primers, matt lacquers and enamels (catalog p.19).The 2019 catalog gives the same 20–30 % S50. |
| Thinner | S80 | 20–30 %recommended | — | Above ~25 °C, large panels/cladding, dry air — to stop dry spray and orange peel.Slower — more dust pick-up and sag risk on verticals. Doesn't change cure time. Not a Technocolor-listed option — test panel first. |
| Additive | CS 10 / CS 20 / CS 21 / CS 22 / CS 23 / CS 30 / CS 40 / CS 50 / CS 51 / CS 53 / CS 60 / CS 70 / CS 80 / CS 90 / CS 91 | — | — | Tinting the converter into an enamel (RAL/NCS) to a SPECTRUM recipe.CS pastes are the solvent-system (PU/acrylic) range per the SPECTRUM tinting leaflet. Add paste to part A and mix BEFORE the hardener. Technocolor publishes no max paste loading. |
Percentages are per 100 parts of component A.
Characteristics
- Solids
- 42 % part Acatalog
- Gloss
- 20 GU 60°catalog
- Elasticity
- highcatalog
- Lightfastness
- high — weather- and lightfast, non-yellowingcatalog
- Chemical resistance
- chemically resistantofficial
- Hardness
- high mechanical resistancecatalog
- Drying · Conditions
- 20 °C
- Drying · Full cure
- 12recommended
- Viscosity · Why ru
- Та же основа, другое содержание матирующей добавки; для M значение не из источника.
Application
HVLP
- Nozzle
- 1.5–1.7 mmrecommended
- Pressure · fluid
- 0.8–1.5 barrecommended
- Pressure · air
- 2–2.2 barrecommended
- Spray viscosity
- 18–22 s DIN4 (4 mm) at 20 °Crecommended
- Consumption
- 150 g/m²official
- Wet film
- 120–150 µmrecommended
- Coats
- 2–3 coatsrecommended
- Flash-off
- 10–15 minrecommended
- Recoat
- 4–24 hrecommended
- Sanding between coats
- P320–P600recommended
Gun distance 15–20 cm, 50 % overlap, fan fully open. Strain (125–190 µm) before spraying.
Conventional spray
- Nozzle
- 1.6–1.8 mmrecommended
- Pressure · air
- 3–4 barrecommended
- Spray viscosity
- 18–22 s DIN4 at 20 °Crecommended
- Consumption
- 150 g/m²official
Air spray is THE catalog method (air-spray pictogram). Transfer efficiency up to 40 % per the methods page — budget for overspray.
Airmix (air-assisted airless)
- Nozzle
- 0.23–0.28 mmrecommended
- Pressure · fluid
- 20–60 barrecommended
- Pressure · air
- 1–2 barofficial
- Spray viscosity
- 25–35 s DIN4recommended
Not listed for this code — fine by standard practice; the methods page says airmix suits topcoats better than airless.
Airless
- Nozzle
- 0.28–0.33 mmrecommended
- Pressure · fluid
- 100–160 barrecommended
- Spray viscosity
- 30–45 s DIN4recommended
Only for big flat areas/cladding where throughput beats finish quality.
Brush
- Allowed
- norecommended
Technocolor lists spray only (150 g/m²). Brush/roller are NOT listed for ATL60180 — unlike the water-borne HTL60/HPL60.
Process and compatibility
- Substrate preparation
- Exterior wood: dry, clean, dust-free; sand solid wood P150–P180. If it will see weather, apply a preservative (CTH100/CPH6) first and let it dry fully (official wood-prep page: impregnate wood exposed to moisture).recommended
- Sanding
- Between coats P320–P400; denib P400–P600 before the last coat; never sand the final 20/30-gloss coat.recommended
- Temperature and humidity · Relative humidity
- 40–75 % RHofficial
- Temperature and humidity · Temperature
- 15–25 °Crecommended
- Temperature and humidity · Wood moisture
- 8–14 %official
- Don'ts
- Don't brush or roll — spray only is listed.
- Don't change the AC40 ratio — 40 % fixed.
- Don't tint with water-based CH pastes — CS (solvent) only.
- Don't spray over wet wood or above 75 % RH.
- Don't sand or polish the 20/30-gloss final coat.
Storage
- Storage temperature
- +5…+25 °C, tightly closed, away from heat; keep AC40 sealed from moisture.recommended
Safety: Flammable, solvent-borne; AC40 hardener contains isocyanates. Spray in an extracted booth, wear an A2P2 carbon respirator (air-fed is better), nitrile gloves and goggles. No naked flames. (Generic 2K acrylic-PU precautions — no Technocolor SDS found.)
Mixed into
CS 10 / CS 20 / CS 21 / CS 22 / CS 23 / CS 30 / CS 40 / CS 50 / CS 51 / CS 53 / CS 60 / CS 70 / CS 80 / CS 90 / CS 91
Sources
Value tags: “official”, “dealer”, “catalog”, “schedule” are Technocolor data; “workshop” is from our own datasheets; “recommended” is our engineering estimate (hover to see the reasoning).
- official page (ATL60180 M, 20 gl): properties, spray 150 g/m²
- 2019 catalog: solids 50 %, 'С40' hardener, S50 20–30 % (superseded)
- t-colormarket search card: 'ATL60180 Конвертер акриловый прозрачный для наружных работ (30гл)'; detail page 404
- application methods (airmix air 1–2 bar, airless up to 200 bar)
- RH 40–75 % during application
- viscosity measured by Ford cup at 20 °C; meaning of characteristics
Not covered by the sources
- viscosity of part A (M variant)
- density
- pot life (no Technocolor figure; treat as a working-day product but mix only what you spray within a few hours — verify)
- dust-free / touch-dry / sand times
- % by volume for AC40 and S50 (only bare % given, assumed by weight)
- max CS paste loading
- shelf life
- packaging sizes
- hardness / chemical resistance test values
- SDS
- official primer for the system
- no dealer listing for the 20-gloss M at all (t-colormarket and Holzkom list only the 30-gloss item)