Skip to content
Dugan Design
← All products
+ Add to shopping list
UV-cureSealer

VTS20002

VTS20002 Clear UV-cure parquet sealer (roller)

Clear UV-curing sealer for industrial roller-coat finishing of parquet. High clarity and flexibility. Applied by roller coater on a line and cured under UV lamps.

  • Sealing parquet / engineered flooring on a UV roller line
  • Intermediate sealer coats under VTL20003 UV topcoat

Single-component product: no mixing needed — use as supplied (see application below).

Ask about VTS20002

Answers are based on the VTS20002 data and the products it mixes with.

Questions and answers are stored to improve the assistant and prevent abuse; the question text is processed by Anthropic (USA). Privacy policy

Mixing matrix

  • none
    % by weight: 100 %recommended

    Always — supplied ready to use

    No hardener or thinner is listed on the product page or in the schedule. Do not cut it with solvent on a UV roller line without Technocolor's OK — solvent won't flash before the lamp.

Percentages are per 100 parts of component A.

Characteristics

Solids
≈98–100 (100 % reactive system) %recommended
Elasticity
highofficial
Transparency
highofficial
Pot life
not applicable — single-component, cures only under UVrecommended
Drying · UV cure
1 UV lamp 80–120 W, 10 m/min after the 1st VTS20002 coat; 3 lamps 80–120 W, 10 m/min after the 2nd coat (before sanding)schedule
Drying · Conditions
UV line

Application

Roller coater (UV)

Consumption
15–20 g/m²official
Consumption, schedule (g/m²)
20–25 g/m²schedule
Coats
2schedule
Cure between coats
UV lamp 80–120 W ×1, 10 m/min after coat 1; ×3 lamps, 10 m/min after coat 2schedule
Sanding between coats
After the 2nd VTS20002 coat is fully cured: sanding belt P240 → P280 → P320, then VTL20003 topcoatschedule
Wet film
≈14–24 µm per coatrecommended

Roller-coat only (per Technocolor's methods page, rollers are for flat parts: panels and parquet). Per Technocolor's schedule the first coat gets one lamp (probably a partial 'gel' cure for intercoat adhesion; that is our reading, not stated); after the second coat, full cure with three lamps before sanding.

HVLP

Nozzle
n/a — do not sprayrecommended

Not intended for spraying. Technocolor makes separate spray-grade UV sealers (VTS30006, VTS60019).

Process and compatibility

Substrate preparation
Sand parquet with belts P150, P180, P220; then VTS20000 100 % + CTH 5–10 % (8–10 g/m², dry 30–35 °C 5 min) → VTS20011 filler 30–35 g/m² + 1 UV lamp → VTS20015 sealer 20–25 g/m² + 1 UV lampschedule
Goes over
VTS20015 / VTS20011 / VTS20000 / VTS20002
Goes under
VTS20002 / VTL20003
Sanding
P240, P280, P320 after full cure of the second VTS20002 coatschedule
Temperature and humidity
Material and boards 18–25 °C, wood MC 8–10 %recommended
Don'ts
  • Don't spray it
  • Don't thin with solvent on a UV line
  • Don't leave it in an open trough in daylight/UV
  • Don't sand before full cure (3-lamp pass)

Storage

Safety: Uncured UV acrylates are skin irritants and sensitisers: nitrile gloves and glasses, wipe spills straight away. Never look at UV lamps unshielded.

Used in finishing systems

Sources

Value tags: “official”, “dealer”, “catalog”, “schedule” are Technocolor data; “workshop” is from our own datasheets; “recommended” is our engineering estimate (hover to see the reasoning).

Not covered by the sources
  • Dealer t-colormarket.ru has no UV-cure category; search for VTS20002 returns no products (re-checked 2026-10-05), so there is no solids, viscosity, density, gloss, dust-free or full-cure data
  • No Technocolor TDS PDF found (web-search budget exhausted; direct dealer searches on lakokraska31/woodonline returned nothing)
  • Not listed in the 2025–2026 catalog transcripts
  • Measured viscosity, density, solids, required UV dose (mJ/cm²), lamp type (Hg/Ga), shelf life, storage temperature, packaging
  • Hardness, chemical resistance, lightfastness, gloss of the cured film
  • Discrepancy: official page 15–20 g/m² vs schedule 20–25 g/m²