UV-cureLacquer

VTL20003

UV-curing clear parquet lacquer (30 gloss per page title; 40 gloss per URL and catalog)

Single-pack, 100 %-solids clear UV-curing lacquer for roller-coater application on parquet and other flat, hard-wearing surfaces. Levels well; excellent abrasion and scratch resistance, high elasticity and chemical resistance. The topcoat in the official 'Parquet finishing (UV)' schedule.

topcoat for parquet / engineered flooring on a UV line
finishing flat, high-wear parts (floor boards, worktop and stair-tread blanks)

Scan to open this page on a phone

Download:PNG SVG

Mix calculator

Ready-to-spray batch

Thinner0.0 %

When: only if needed and after a test panel; prefer warming the material

Ratio 100 : 0.0

Component	Weigh out
VTL20003part A	500 g
VTL10000Thinner	0.0 g
Total	500 g

Pot life of the mix: n/a (1K, cures only under UV).

Ask about VTL20003

Answers are based on the VTL20003 data and the products it mixes with.

Mixing matrix

none
No hardener or thinner listed by the manufacturer: 1K, use as supplied.
VTL10000Thinner
% by weight: 0–5 %recommended% by volume: 0–5 %recommended
only if needed and after a test panel; prefer warming the material

Role	Material	% by weight	% by volume	When
none		—	—	No hardener or thinner listed by the manufacturer: 1K, use as supplied.
Thinner	VTL10000	0–5 %recommended	0–5 %recommended	only if needed and after a test panel; prefer warming the material

Percentages are per 100 parts of component A.

Characteristics

Solids: 100 %catalog
Gloss: 30 (заголовок) / 40 (каталог, URL) GU (60°)official
Abrasion resistance: highofficial
Scratch resistance: excellentcatalog
Elasticity: highcatalog
Chemical resistance: high physical-chemical resistanceofficial
Levelling: levels wellofficial
Pot life: n/a (1K, cures only under UV)recommended
Drying · UV cure: 80–120 Вт, 3 лампы, 10 м/минschedule
Drying · Intermediate gel: optional: 1 lamp 80–120 W @10 m/min between passes (or wet-on-wet with two roller heads)recommended
Drying · Flash-off: 0 minrecommended
Drying · Conditions: UV cure; material ~20–30 °C

Colours

VTL20003 · clear

Application

Roller coater (UV)

Coats: 2schedule
Wet film: 7–18 µmrecommended
Flash-off: 0 minrecommended
Recoat: straight after gel cure, or wet-on-wetrecommended
Sanding between coats: P240, P280, P320 по отвержденному грунту перед лакомschedule
Nozzle: n/a (roller only)recommended

Flat parts only. Adjust viscosity with material temperature. Cure right after application; keep the lacquer away from daylight.

Process and compatibility

Substrate preparation: Шлифование P150, P180, P220 → VTS20000 + CTH 5–10 % (8–10 г/м², сушка 30–35 °C 5 мин) → шпаклёвка VTS20011 30–35 г/м² → УФ → VTS20015 20–25 г/м² → УФ → VTS20002 20–25 г/м² ×2 с УФ → шлифование P240–P320 → VTL20003schedule
Goes over: VTS20002 / VTS20015 / VTS20011 / VTS20000
Sanding: P240, P280, P320 перед лакомschedule
Temperature and humidity: 18–25 °C, RH 50–65 %recommended
Don'ts: don't spray it
don't thin with ordinary solvents (S30/S31) for roller application: the line has no flash-off zone, so the solvent stays in the film
don't leave it in the tray under daylight
not for profiled parts

Storage

Safety: UV acrylates can sensitise skin: nitrile gloves, safety glasses; shield eyes from the UV lamps. Uncured lacquer is hazardous waste.

Used in finishing systems

Parquet finishing (UV-cure roller line)

Sources

Value tags: “official”, “dealer”, “catalog”, “schedule” are Technocolor data; “workshop” is from our own datasheets; “recommended” is our engineering estimate (hover to see the reasoning).

Not covered by the sources

dealer page (t-colormarket.ru search returns nothing for VTL20003; the shop has no UV-curing category, re-checked 2026-10-05)
no TDS/SDS found (dealer probes lakokraska31/woodonline/ndom31 empty)
viscosity
density
exact gloss (30 vs 40 conflict on official sources)
UV dose (mJ/cm²) / lamp type
shelf life, storage temperature, packaging
hardness/abrasion figures (Taber etc.)