Skip to content
Dugan Design
← All products
+ Add to shopping list
UV-cureSealer

VTS20015

VTS20015 UV-cure parquet sealer (roller)

UV-curing sealer for industrial roller-coat parquet finishing. Has no product page on t-color.ru — it appears only in the official 'Parquet finishing (UV)' schedule as the first sealer coat over the VTS20011 filler-primer, before two coats of VTS20002.

  • First sealer coat over VTS20011 UV filler on a parquet UV roller line
  • Base for VTS20002 sealer and VTL20003 UV topcoat

Single-component product: no mixing needed — use as supplied (see application below).

Ask about VTS20015

Answers are based on the VTS20015 data and the products it mixes with.

Questions and answers are stored to improve the assistant and prevent abuse; the question text is processed by Anthropic (USA). Privacy policy

Mixing matrix

  • none
    % by weight: 100 %schedule% by volume: 100 %schedule

    Always — the schedule uses it neat

    No hardener or thinner is listed anywhere for VTS20015. Don't add solvent on a UV roller line — it won't flash off before the lamp.

Percentages are per 100 parts of component A.

Characteristics

Solids
≈98–100 (100 % reactive system) %recommended
Pot life
not applicable — single-component, cures only under UVrecommended
Drying · UV cure
1 UV lamp 80–120 W at 10 m/min before the next VTS20002 coatschedule
Drying · Conditions
UV line

Application

Roller coater (UV)

Consumption
20–25 g/m²schedule
Coats
1schedule
Cure between coats
UV lamp 80–120 W ×1, 10 m/min, then VTS20002schedule
Wet film
≈18–24 µmrecommended

Roller-coat only (Technocolor's methods page: rollers are for flat parts — panels and parquet; 5–20 g/m² per pass; UV materials at 98–100 % solids). One lamp after the coat — partial cure for intercoat adhesion to VTS20002.

HVLP

Nozzle
n/a — do not sprayrecommended

Not for spraying. Technocolor makes separate spray-grade UV sealers (VTS30006, VTS60019).

Process and compatibility

Substrate preparation
Sand parquet with belts P150, P180, P220 → VTS20000 + CTH 5–10 % (8–10 g/m², dry 30–35 °C 5 min) → VTS20011 filler 30–35 g/m² + 1 UV lamp → VTS20015schedule
Goes over
VTS20011 / VTS20000
Goes under
VTS20002 / VTL20003
Sanding
No sanding straight after VTS20015; sanding P240, P280, P320 only after the second VTS20002 coat is fully cured (3 lamps)schedule
Temperature and humidity · Wood moisture
8–14 %official
Temperature and humidity · Air humidity
40–75 %official
Temperature and humidity · Temperature
Material and boards ≈18–25 °Crecommended
Don'ts
  • Don't spray it
  • Don't thin with solvent on a UV line
  • Don't leave it in an open trough in daylight/UV
  • Don't fully cure it before VTS20002 — the schedule uses just one lamp

Storage

Safety: Uncured UV acrylates are skin irritants and sensitisers: nitrile gloves and glasses, wipe spills straight away. Never look at UV lamps unshielded.

Used in finishing systems

Sources

Value tags: “official”, “dealer”, “catalog”, “schedule” are Technocolor data; “workshop” is from our own datasheets; “recommended” is our engineering estimate (hover to see the reasoning).

Not covered by the sources
  • No official t-color.ru product page — only the UV parquet schedule mentions it
  • Dealer t-colormarket.ru search for VTS20015 returns no product (re-checked 2026-10-05) — no solids, viscosity, density, gloss data
  • No Technocolor TDS PDF found (session web-search budget exhausted)
  • Not in the 2025–2026 catalog transcripts
  • Transparency/colour not stated (derived as clear from the schedule); measured solids, viscosity, density, UV dose (mJ/cm²), lamp type, cured-film hardness/chemical resistance
  • Shelf life, storage temperature, packaging
  • How VTS20015 differs from VTS20002 is not explained by any source (the VTS20002 page only says 'high transparency and elasticity', roller 15–20 g/m², while the schedule uses both at 20–25 g/m²)