VPL60100
VPL60100 UV-curing white gloss enamel
White, high-gloss pigmented UV-curing enamel for spray application. Gives a high-gloss finish. Cures only under UV lamps — it will not dry on its own in air.
- White high-gloss topcoat for furniture fronts and panels on spray lines with UV curing
Mix calculator
Ratio 100 : 20.0
| Component | Weigh out |
|---|---|
| VPL60100part A | 417 g |
| S11Thinner | 83.3 g |
| Total | 500 g |
Covers roughly 4.35 m² at 115 g/m².
Ask about VPL60100
Answers are based on the VPL60100 data and the products it mixes with.
Mixing matrix
- % by weight: 0–10 (typ. 5) %recommended% by volume: 0–14 (typ. 7) %recommended
Only to trim spray viscosity. S31 is the default (medium evaporation); S13/S30 when you need a fast flash-off.
No hardener — single-component UV system. All solvent must be gone before the lamp, or you get bubbling and dull patches.
- S11Thinner% by weight: 20 %schedule% by volume: 28 %recommended
Analogue from the official schedule: UV lacquer VTL30040 : S11 = 100 : 20 sprayed on mouldings. Not published for VPL60100 — a reference point, not a spec.
S11 is catalogued for polyester gloss lacquers; use with the enamel only after a test panel.
| Role | Material | % by weight | % by volume | When |
|---|---|---|---|---|
| Thinner | S13 / S30 / S31 | 0–10 (typ. 5) %recommended | 0–14 (typ. 7) %recommended | Only to trim spray viscosity. S31 is the default (medium evaporation); S13/S30 when you need a fast flash-off.No hardener — single-component UV system. All solvent must be gone before the lamp, or you get bubbling and dull patches. |
| Thinner | S11 | 20 %schedule | 28 %recommended | Analogue from the official schedule: UV lacquer VTL30040 : S11 = 100 : 20 sprayed on mouldings. Not published for VPL60100 — a reference point, not a spec.S11 is catalogued for polyester gloss lacquers; use with the enamel only after a test panel. |
Percentages are per 100 parts of component A.
Characteristics
- Gloss
- высокий глянец (high gloss)official
- Drying · Cure mechanism
- УФ-отверждение (UV cure) — category 'Материалы УФ отверждения'official
- Drying · Pre-dry
- 30–35 °C, 5–10 мин (5–10 min) before UV lampsschedule
- Drying · UV cure
- 80–120 Вт (W) лампы ×3, 10 м/мин (m/min)schedule
- Drying · UV lamp type
- Hg + Ga-doped (Fe/Ga) lamp combination; slower belt than for clear lacquersrecommended
- Drying · Conditions
- line / 20–35 °C
Colours
- VPL60100 · white
Application
HVLP
- Consumption
- 110–120 g/m²official
- Nozzle
- 1.5–1.8 mmrecommended
- Pressure · air
- 2–2.5 barrecommended
- Spray viscosity
- 18–24 s DIN4 (20 °C)recommended
- Wet film
- 80–100 µmrecommended
- Coats
- 1 full coat over a sanded UV/PU primerrecommended
- Flash-off
- 5–10 min at 30–35 °C before the lampschedule
- Sanding between coats
- If recoating: cure fully, sand P320–P400, dedust, recoatrecommended
Use opaque hoses and cups (metal or UV-blocking plastic); do not leave material in a translucent cup in daylight — it will start to gel.
Conventional spray
- Consumption
- 110–120 g/m²official
- Nozzle
- 1.5–1.8 mmrecommended
- Pressure · air
- 3–4 barrecommended
- Transfer
- до 40 %official
Transfer efficiency up to 40 % (official methods page).
Airmix (air-assisted airless)
- Consumption
- 110–120 g/m²official
- Nozzle
- 0.23–0.33 mmrecommended
- Tip (thou)
- 9–13 thourecommended
- Pressure · fluid
- null–20 barofficial
- Pressure · Fluid working pressure
- 60–100 barrecommended
- Pressure · air
- 1–2 barofficial
For topcoats airmix is preferred over airless (official methods page).
Electrostatic
Possible with all spray types (official methods page). Our note: for a white enamel check the material's resistivity first.
Process and compatibility
- Substrate preparation
- MDF/panels primed with white UV primer VPS60011 (or compatible PU white primer), cured, sanded P320–P400, dedustedrecommended
- Goes over
- VPS60011
- Sanding
- Primer P320–P400 before enamel; between enamel coats P400 after full curerecommended
- Temperature and humidity
- Material and room 20–25 °C, RH 50–70 %; pre-dry 30–35 °Crecommended
- Don'ts
- Do not add hardeners or PU/acrylic components — it is not a 2K system
- Do not send to the lamp without a flash-off — solvent will boil
- Do not lay more than ~120 g/m² per pass (official rate 110–120 g/m²) — white pigment blocks through-cure of a thick film
- Do not store or hold in clear containers in light
Storage
Safety: Contains reactive acrylate monomers — skin sensitiser: nitrile gloves, goggles, ventilation. UV lamps — shield eyes and skin from the radiation.
Sources
Value tags: “official”, “dealer”, “catalog”, “schedule” are Technocolor data; “workshop” is from our own datasheets; “recommended” is our engineering estimate (hover to see the reasoning).
- official product page: high gloss; spray 110–120 g/m²
- application methods (airmix up to 20 bar fluid, 1–2 bar air; conventional ~40 % transfer)
- UV spray lacquer schedule: VTL30040:S11 100:20, pre-dry 30–35 °C 5–10 min
- UV cure settings 80–120 Вт (W) ×3 lamps, 10 m/min; pre-dry 30–35 °C 5 min for VTL30100
- dealer search — no result
Not covered by the sources
- No dealer page: t-colormarket.ru search for VPL60100 returns nothing (UV range not sold there); woodonline.ru no result
- No TDS found (web search budget exhausted; t-colormarket.ru search re-checked 2026-10-05 — no result)
- Solids %, viscosity, density, numeric gloss units, lamp dose (mJ/cm²), lamp type
- Thinner type and ratio (only catalog applicability of S13/S30/S31 to UV materials)
- Pot life / shelf life / storage temperature / packaging
- Not used in any official finishing schedule
- Compatible primer not officially stated (VPS60011 inferred)
- Hardness, chemical resistance, lightfastness/yellowing data