PTL10 M
PTL10 M Universal clear PU lacquer, matt (20 gloss)
Two-pack fast-drying clear polyurethane lacquer, matt (20 gloss). Fills the pores well without sinking into the substrate, dries fast, flows out nicely, very clear, leaves a pleasant-to-the-touch surface. Topcoat for furniture in any wood species.
- Clear topcoat for furniture in any wood species
- Clear finish on case goods and fronts over PU sealer
- Open- or closed-pore veneer finishing — fills the pores without sinking back
Mix calculator
Ask about PTL10 M
Answers are based on the PTL10 M data and the products it mixes with.
Mixing matrix
- PC20Hardener% by weight: 40 %official% by volume: 40 %official
Standard (only official) recipe
- PC20Hardener% by weight: 40 %dealer% by volume: 40 %dealer
Dealer — same as official
- PC20Hardener% by weight: 40 %catalog
2025–2026 catalogue
- S50Thinner% by weight: 20–30 (typ. 25) %official% by volume: 25–35 %official
Standard, 18–25 °C
Dealer gives the same 20–30 % by weight / 25–35 % by volume; catalogue S50 20–30 %.
- S50Thinner% by weight: 20–30 %dealer% by volume: 25–35 %dealer
Dealer
- S80Thinner% by weight: 20–30 %recommended
Hot shop (above ~25 °C), large flat panels
Slow thinner: better flow-out but more dust pick-up and sag risk on verticals. Does not change cure time.
| Role | Material | % by weight | % by volume | When |
|---|---|---|---|---|
| Hardener | PC20 | 40 %official | 40 %official | Standard (only official) recipe |
| Hardener | PC20 | 40 %dealer | 40 %dealer | Dealer — same as official |
| Hardener | PC20 | 40 %catalog | — | 2025–2026 catalogue |
| Thinner | S50 | 20–30 (typ. 25) %official | 25–35 %official | Standard, 18–25 °CDealer gives the same 20–30 % by weight / 25–35 % by volume; catalogue S50 20–30 %. |
| Thinner | S50 | 20–30 %dealer | 25–35 %dealer | Dealer |
| Thinner | S80 | 20–30 %recommended | — | Hot shop (above ~25 °C), large flat panelsSlow thinner: better flow-out but more dust pick-up and sag risk on verticals. Does not change cure time. |
Percentages are per 100 parts of component A.
Characteristics
- Solids
- 43 % part Acatalog
- Viscosity
- 50–70 srecommended
- Density
- ≈ 1.00–1.05 g/mLrecommended
- Gloss
- 20 gloss units (60°)official
- Pot life
- 4 hrecommended
- Drying · Touch-dry
- 25 minrecommended
- Drying · Full cure
- 4 hrecommended
- Drying · Dust-free
- 10–15 minrecommended
- Drying · Sand or stack
- 4–8 hrecommended
- Drying · Conditions
- 20 °C
- Chemical resistance
- не указано численно; позиционируется как универсальный мебельный ПУ-лакcatalog
- Lightfastness
- на PC20 (ароматический изоцианат) возможно лёгкое пожелтение со временем на светлых породахrecommended
Application
HVLP
- Nozzle
- 1.3–1.5 (typ. 1.4) mmrecommended
- Pressure · air
- 1.8–2.2 barrecommended
- Spray viscosity
- 18–22 srecommended
- Consumption
- 120–150 g/m²official
- Coats
- 1–2 over a sanded PU sealer; 2 when used self-sealing on bare woodrecommended
- Wet film
- 110–150 µmrecommended
- Flash-off
- 10–20 minrecommended
- Recoat
- wet-on-tack within 20–30 min, or after ≥ 4 h with denibrecommended
- Sanding between coats
- P320–P400 denib between coats; sealer below sanded P240–P320recommended
- Gun setup
- distance 15–20 cm, 50–75 % overlap, fan fully open, ~10–13 CFMrecommended
Stir thoroughly before adding hardener — the matting agent settles (dealer: 'mix thoroughly before use'). Don't sand or polish the final matt coat — the sheen goes patchy.
Conventional spray
- Nozzle
- 1.4–1.6 mmrecommended
- Pressure · air
- 3–4 barrecommended
- Consumption
- 120–150 g/m²official
More overspray and waste than HVLP.
Airmix (air-assisted airless)
- Nozzle
- 0.23–0.28 mmrecommended
- Pressure · fluid
- 10–20 barrecommended
- Pressure · air
- 1–2 barofficial
- Consumption
- 120–150 g/m²official
Methods page: airmix suits topcoats better than airless.
Electrostatic
Possible on conductive/pre-treated parts; no Technocolor data for PTL10.
Process and compatibility
- Substrate preparation
- dry wood (8–12 % MC), sand P150–P220, dedust; stain if required; PU sealer (e.g. PTS20, 150 g/m²), sand P240–P320recommended
- Goes over: why
- clear 2K PU sealers (PTS20 in the official PU door schedule; PTS10 is the fast-sanding clear PU sealer from the same catalogue page)recommended
- Temperature and humidity
- apply 18–25 °C, RH 50–70 %; data quoted at 20 °Crecommended
- Don'ts
- Don't use a mix older than ~4 h
- Don't sand or polish the final matt coat
- Don't exceed 30 % thinner — build drops and the sheen shifts
- Don't spray over damp wood or in high humidity
- Don't swap PC20 for another hardener untested — only PC20 is official for M
Storage
- Packaging
- 1 L, 5 L, 25 Ldealer
Safety: Two-pack, solvent-borne, isocyanate hardener: spray booth with extraction, respirator (A2 cartridges or air-fed), nitrile gloves, goggles. Highly flammable.
Sources
Value tags: “official”, “dealer”, “catalog”, “schedule” are Technocolor data; “workshop” is from our own datasheets; “recommended” is our engineering estimate (hover to see the reasoning).
- official page: name, properties, spray 120–150 g/m², PC20 40/40 %, S50 20–30 % wt / 25–35 % vol
- dealer page: description, use, mix table (same as official), packaging 1/5/25 L, 'mix thoroughly' note; no tech table
- sibling PTL10 SM dealer page: gloss 30±3, solids 40±1 %, pot life 4 h, touch 25 min, full 4 h; hardener PC10 50 %
- sibling PTL10 G dealer page: same PC20 40 / S50 recipe
- sibling PTL10 UM dealer page: same PC20 40 / S50 recipe
- application methods
- characteristics vocabulary
- sister PTL20 M dealer page: solids 42±1 %, viscosity A 60±5 s VZ-4, PC20/PC25 50 %, PC60 for yellowing resistance, S70/S80 in hot weather
- official PU panel-door schedule: P150–P220 → PTS20 sealer ×2 (P240–P320) → PTL20 lacquer
Not covered by the sources
- PTL10 M official page exists online but was not in the local mirror (fetched live); it carries no tech table
- viscosity of part A — not published for any PTL10 grade (derived)
- pot life, touch-dry and full-dry are published only for sibling PTL10 SM (which uses PC10 50 %, not PC20 40 %) — not confirmed for M
- solids: catalog 43 % (family) vs SM dealer 40 ± 1 % — no M-specific figure
- dust-free time, stack/sand time — derived
- density, hardness, elasticity, chemical-resistance figures — not published
- shelf life / storage temperature — not published
- no finishing schedule (information/technology) uses PTL10
- nozzle/pressure — no Technocolor data, all derived
- no Technocolor TDS PDF found (web search budget exhausted; other dealers checked: woodonline lists only PTL10 SM, lakokraska31/ndom31 no hits)
- no slow-thinner (S70/S80) or non-yellowing hardener (PC60) option published for PTL10
- pot life and touch/full drying for M are carried over from sibling PTL10 SM (different hardener PC10 50 %) — now tagged derived
- airmix fluid pressure: official methods page only gives 'up to 20 bar'