PPL01
PPL01 white fire-retardant PU enamel, matt (20 gloss)
Two-pack white matt polyurethane enamel with fire-retardant additives. Good hiding power, good physical and chemical resistance. When heated the fire-retardant components break down and give off a non-combustible gas that cuts off oxygen and slows flame spread. Over the PPS01 fire-retardant primer it rates Group I fire-protection efficiency to GOST R 53292-2009 (cl. 6.1). No official t-color.ru page — data from the dealer (t-colormarket.ru) and the Technocolor 'Fire-retardant materials' leaflet.
- protecting interior timber structures and raising their fire resistance
- white opaque fire-retardant finish: wall panelling, doors, furniture, public-building interiors
- top coat of System 2 (pigmented): PPS01 → PPL01, Group I to GOST R 53292-2009
Mix calculator
Ask about PPL01
Answers are based on the PPL01 data and the products it mixes with.
Mixing matrix
- PC20Hardener% by weight: 50 %dealer% by volume: 70 %dealer
Standard option; slightly more elastic film.
Dealer and leaflet list PC20 / PC60 as alternatives — use one or the other, don't blend.
- PC60Hardener% by weight: 50 %dealer% by volume: 70 %dealer
When the white must resist yellowing (bright interiors, near windows, under lighting).
Same ratio, 50 % by weight / 70 % by volume.
- S50Thinner% by weight: 20–30 (typ. 25) %dealer% by volume: 30–35 %dealer
Always; S50 is the universal, normal-evaporation thinner (verticals, normal shop).
20 % for verticals and maximum build; 30 % on flats for better flow-out. Thinner doesn't change cure time.
- S80Thinner
Only in hot weather (above ~25 °C) or on large flat panels, instead of S50.
More dust pick-up and sag risk; avoid on verticals. Fire tests were done with S50 — stick to S50 on certified jobs.
| Role | Material | % by weight | % by volume | When |
|---|---|---|---|---|
| Hardener | PC20 | 50 %dealer | 70 %dealer | Standard option; slightly more elastic film.Dealer and leaflet list PC20 / PC60 as alternatives — use one or the other, don't blend. |
| Hardener | PC60 | 50 %dealer | 70 %dealer | When the white must resist yellowing (bright interiors, near windows, under lighting).Same ratio, 50 % by weight / 70 % by volume. |
| Thinner | S50 | 20–30 (typ. 25) %dealer | 30–35 %dealer | Always; S50 is the universal, normal-evaporation thinner (verticals, normal shop).20 % for verticals and maximum build; 30 % on flats for better flow-out. Thinner doesn't change cure time. |
| Thinner | S80 | — | — | Only in hot weather (above ~25 °C) or on large flat panels, instead of S50.More dust pick-up and sag risk; avoid on verticals. Fire tests were done with S50 — stick to S50 on certified jobs. |
Percentages are per 100 parts of component A.
Characteristics
- Solids
- 64 ± 1 %dealer
- Viscosity
- 10 ± 5 sdealer
- Density
- ≈1.3–1.45 g/cm³ (part A) g/cm³recommended
- Gloss
- 20 ± 3 GU (measuring angle not stated by dealer; 60° assumed)dealer
- Pot life
- 4 hdealer
- Drying · Touch-dry
- 30 mindealer
- Drying · Full cure
- 8 hdealer
- Drying · Sand or stack
- 4–8 h (denib after ~4 h, stack/pack after 8 h + overnight preferred)recommended
- Drying · Conditions
- 20 °C
- Drying · Fast drying
- fast dryingcatalog
- Hardness
- scratch resistant; sands easilycatalog
- Chemical resistance
- хорошая / высокая физико-химическая стойкость / good-to-high physical and chemical resistancedealer
- Hiding power
- high hiding powerdealer
- Flow
- excellent flow-outcatalog
- Fire protection
- Group I fire-protection efficiency, GOST R 53292-2009 cl. 6.1dealer
- Lightfastness
- good with PC60, moderate with PC20 (white may yellow slightly with time)recommended
- Durability
- long service lifecatalog
Colours
- PPL01 · white
Application
HVLP
- Consumption
- 150 g/m²dealer
- Pressure · fluid
- gravity cup; pressure pot 0.8–1.5 barrecommended
- Coats
- 1 full coat at 150 g/m², or 2 lighter wet-on-wet passes adding up to 150 g/m²recommended
- Recoat
- after ~4 h with a denib; within 24 h without heavy sandingrecommended
- Sanding between coats
- P320–P400 or grey pad, denib onlyrecommended
HVLP, 1.8 mm (1.7–1.9), 2.0–2.5 bar inlet trigger pulled, ≤0.7 bar at the cap, fan fully open, 15–20 cm, 50–75 % overlap. Stir part A right to the bottom first (dealer: 'mix thoroughly before use') — the fire-retardant fillers settle. Strain the mix (125–190 µm). Keep the 150 g/m² rate even — both the fire rating and an even matt sheen depend on it. source
Conventional spray
- Consumption
- 150 g/m²dealer
Air spray: transfer efficiency up to ~40 % (methods page) — you'll use more than 150 g/m² of material per part. official
Airmix (air-assisted airless)
- Nozzle
- 09–11 thou (0.23–0.28 mm), 40–50° fanrecommended
For production runs of panels and doors. Not published by Technocolor — test first and check the 150 g/m² rate by weighing a test panel.
Airless
- Nozzle
- 11–13 thou (0.28–0.33 mm)recommended
Large flat parts only; finish quality is below airmix/HVLP.
Brush
Not recommended: Technocolor lists spray only and the fire rating is for spraying at 150 g/m². Brush only for small touch-ups, not on certified work. recommended
Process and compatibility
- Substrate preparation
- Dry timber/plywood/MDF (8–12 % MC), sanded P180–P240 and de-dusted. Prime with PPS01 fire-retardant primer (150 g/m²), sand P280–P320 when dry, de-dust, then PPL01.recommended
- Goes over
- PPS01
- System
- Система 2 (пигментная): PPS01 + (PC20 или PC60 50 %) + S50 20–30 % → PPL01 + (PC20 или PC60 50 %) + S50 20–30 %; распыление, 150 г/м² каждый; I группа ГОСТ Р 53292-2009catalog
- Temperature and humidity
- 18–25 °C, RH 50–70 %; part A and hardener at room temperaturerecommended
- Don'ts
- don't go under or over 50 % hardener
- don't apply less than 150 g/m² — the fire rating is for this system at this rate
- don't swap PPS01 for an ordinary primer if you need the GOST fire rating
- not for exterior use — interior only
- don't use the mix past 4 h pot life
- don't sand or polish the final matt coat — you'll get shiny patches
- don't leave the hardener can open
Storage
- Packaging
- 1 kg,5 kg,25 kgdealer
- Shelf life
- not published — typically 12 months unopenedrecommended
- Storage temperature
- +5…+30 °C, sealed, away from heat and flamerecommended
Safety: Solvent-borne 2K PU: flammable (the cured film is fire-retardant, the wet material is not). The hardener contains isocyanates — airway and skin sensitiser. Use an extracted booth, A2P3 respirator or air-fed mask, nitrile gloves and goggles.
Sources
Value tags: “official”, “dealer”, “catalog”, “schedule” are Technocolor data; “workshop” is from our own datasheets; “recommended” is our engineering estimate (hover to see the reasoning).
- dealer product page: properties, use, Group I rating, PC20/PC60 50 wt%/70 vol%, S50 20–30 wt%/30–35 vol%, gloss 20±3, solids 64±1 %, viscosity 10±5 s CF-8, pot life 4 h, touch 30 min, full 8 h, 150 g/m², packaging, price
- dealer page of partner primer PPS01
- dealer page of sibling PTL01 (hardener alternatives note, hot-weather thinners)
- official application methods page
Not covered by the sources
- no official t-color.ru product page (fire-retardant section empty)
- no Technocolor TDS/SDS PDF found (web search budget exhausted this session; leaflet + dealer only)
- density not published (derived)
- shelf life not published
- stack/sand time, recoat window not published
- nozzle/pressure not published (derived)
- hardness / lightfastness / elasticity numbers not published
- no finishing schedule on t-color.ru uses PPL01
- S80 not approved for PPL01 by Technocolor (derived option only)
- whether a non-fire-retardant topcoat over PPL01 keeps the Group I rating — not stated
- tint (RAL/NCS) availability stated only range-wide in the leaflet, not for PPL01 specifically
- PPS01 with PC60: leaflet lists PC20/PC60 for System 2, but the PPS01 dealer page lists PC20 only
- CF-8 cup not defined by Technocolor (taken as 8 mm flow cup); no DIN4 value for part A or spray mix published
- dealer S50 weight→volume pair (20–30 wt % → 30–35 vol %) is internally inconsistent at the 30 % end