APL80094
APL80094 Decorative effect 'Brass' (metallised enamel)
Two-pack acrylic metallised enamel loaded with metal particles that imitates brass. Once cured, the particles are sanded/polished P320→P1500 to a deep metallic shine, optionally aged with patina or the D100 rust effect, then sealed with an acrylic clear.
- exclusive finishing of furniture fronts and panels in various wood species and MDF
- polished-brass imitation
- base coat for the D100 rust effect
- aged brass with CQS patina
Mix calculator
Ask about APL80094
Answers are based on the APL80094 data and the products it mixes with.
Mixing matrix
- AC40Hardener% by weight: 20 %dealer% by volume: 30 %dealer
always — it is a two-pack material
Fixed 20 % by weight. Stir the base thoroughly before adding hardener — the metal settles to the bottom.
- S50Thinner% by weight: 20–30 (typ. 25) %dealer% by volume: 30–50 (typ. 40) %dealer
standard, normal evaporation
Default 25 % is mid-range, not a sourced value.
- S80Thinner% by weight: 20–30 %recommended% by volume: 30–50 %recommended
heat above ~25 °C, large panels
Slower — more dust pick-up and sag risk; stick with S50 on verticals.
| Role | Material | % by weight | % by volume | When |
|---|---|---|---|---|
| Hardener | AC40 | 20 %dealer | 30 %dealer | always — it is a two-pack materialFixed 20 % by weight. Stir the base thoroughly before adding hardener — the metal settles to the bottom. |
| Thinner | S50 | 20–30 (typ. 25) %dealer | 30–50 (typ. 40) %dealer | standard, normal evaporationDefault 25 % is mid-range, not a sourced value. |
| Thinner | S80 | 20–30 %recommended | 30–50 %recommended | heat above ~25 °C, large panelsSlower — more dust pick-up and sag risk; stick with S50 on verticals. |
Percentages are per 100 parts of component A.
Characteristics
- Solids
- 50 %dealer
- Density
- 1.3–1.5 g/cm³ (part A)recommended
- Viscosity · Why ru
- Значения дилера/каталога нет; см. spray_viscosity в разделе нанесения.
- Pot life
- 6 hdealer
- Drying · Touch-dry
- 20 mindealer
- Drying · Full cure
- 24 hdealer
- Drying · Sand or stack
- 24 hrecommended
- Drying · Conditions
- 20 °C
- Thixotropy · Why ru
- Значка или указания на тиксотропность для этого кода не найдено.
Colours
- APL80094 · Brass
Application
HVLP
- Consumption
- 120–150 g/m²dealer
- Nozzle
- 1.7–1.8 mmrecommended
- Pressure · air
- 2–2.5 bar (gun inlet, trigger pulled)recommended
- Spray viscosity
- 18–22 s DIN4recommended
- Wet film
- 100–130 µmrecommended
- Coats
- 1–2 coatsrecommended
- Flash-off
- 10–20 minrecommended
- Sanding between coats
- no sanding between coats; after full cure (24 h) polish P320 → P1500 grit by gritcatalog
Hold 15–20 cm off, 50 % overlap, steady pass speed. Stir before filling the cup and while working — the metal drops out fast. Don't flood it: a heavy film cures slower and clogs the paper when you polish.
Conventional spray
- Nozzle
- 1.6–1.8 mmrecommended
- Pressure · air
- 3–3.5 barrecommended
- Consumption
- 120–150 g/m²dealer
Airmix (air-assisted airless)
- Nozzle
- 0.28–0.33 mm (≈11–13 thou)recommended
- Pressure · fluid
- 20 barofficial
- Pressure · air
- 1–2 barofficial
- Consumption
- 120–150 g/m²dealer
Check the gun/pump filter doesn't strain out the metal (60 mesh or coarser).
Spray low pressure D100 overcoat
For the rust effect spray D100 over the dried and sanded brass at LOW air pressure — the look depends on droplet size and how heavily you apply it.
Process and compatibility
- Substrate preparation
- primed panel: white primer PPS50 (catalog, 'Metallised enamel') or PPS20 (catalog, 'Rust'), sandedcatalog
- Goes under
- ATL20 SM / CQS / D100 / ATL20005
- Sanding
- after drying, polish the metal particles through P320 up to P1500 in sequence to a deep metallic shinecatalog
- Temperature and humidity
- 18–25 °C, 50–70 % RHrecommended
- Don'ts
- don't polish before full cure (24 h)
- don't skip grits — P320 scratches show in the metal
- don't cut through to the primer on edges
- don't lay it on heavy
Storage
- Packaging
- 1 kgdealer
Safety: Contains organic solvents; AC40 is an isocyanate hardener. Spray in a booth with extraction, wear an A2P2 respirator, gloves and eye protection. Wear the mask for the metal sanding dust too. (General rules, not from a TDS.)
Sources
Value tags: “official”, “dealer”, “catalog”, “schedule” are Technocolor data; “workshop” is from our own datasheets; “recommended” is our engineering estimate (hover to see the reasoning).
- dealer product page: properties, application, consumption 120–150 g/m², AC40 20 % w / 30 % vol, S50 20–30 % w / 30–50 % vol, solids 50±1 %, pot life 6 h, touch 20 min, full 24 h, 1 kg pack
- sibling APL80093 Copper — same solids/pot life/drying/AC40, S50 35–50 % vol (vs 30–50 %), D100 low-pressure note
- airmix: fluid up to 20 bar, atomising air 1–2 bar; airless up to 200 bar
Not covered by the sources
- no official t-color.ru page
- no TDS/SDS PDF found (web-search budget exhausted; lakokraska31/woodonline/ndom31 searches returned nothing)
- viscosity (part A) not published
- density not published (only estimated)
- gloss units of the finished effect not published
- dust-free time not published (touch 20 min only)
- official nozzle/pressure not published
- shelf life and storage temperature not published
- hardness/lightfastness/chemical resistance not published
- not in the main 2025–2026 catalog transcripts