APL70 R1015 SM
Acrylic enamel, RAL 1015 light ivory, 30-gloss semi-matt, 400 ml spray can
Semi-matt (30-gloss) acrylic enamel in a spray can, RAL 1015 light ivory. Ready to spray, no overspray halo, fast drying, rich colour and good hiding. Comes with two caps: a halo-free cap for touch-ups and blending in, and a full-coat cap for priming/first coats.
- all wood species
- first finish on small areas
- restoring the surface after a defect repair
- evening out sheen
- furniture touch-up and repair work
Single-component product: no mixing needed — use as supplied (see application below).
Ask about APL70 R1015 SM
Answers are based on the APL70 R1015 SM data and the products it mixes with.
Characteristics
- Solids
- ≈15–25 %recommended
- Viscosity
- n/arecommended
- Gloss
- 30 gloss units (Technocolor «глосс», % reflected light; 60° geometry assumed for mid gloss per information__characteristics)dealer
- Pot life
- n/a (1K, ready-to-use)recommended
- Drying · Touch-dry
- 10–20 mindealer
- Drying · Full cure
- 3–4 hdealer
- Drying · Recoat (min)
- 5–10 minrecommended
- Drying · Sand or stack
- ≥ 4 (overnight preferred) hrecommended
- Drying · Conditions
- 20 °C
- Hiding
- high hiding powercatalog
- Colour strength
- rich, saturated colourdealer
- Lightfastness
- expected non-yellowing for an acrylic; RAL1015 is itself an ivory tonerecommended
- Chemical resistance
- lower than 2K APL20/APL R1015 Mrecommended
Colours
- RAL 1015 · light ivory
Application
Aerosol
- Nozzle
- supplied caps: 1 × halo-free (blend/touch-up) + 1 × full-coat (primary coat)catalog
- Pressure
- n/a — fixed can pressurerecommended
- Gun distance
- 15–25dealer
- Consumption
- 80–100 g/m²dealer
- Coverage per can
- ≈2.5–3.5 m² per coat m²recommended
- Coats
- 2–3 thin coatsrecommended
- Flash-off
- 5–10 minrecommended
- Recoat
- 5–10 min wet-on-wet passes, or after full dry (3–4 h) with a light scuffrecommended
- Sanding between coats
- P400–P600 (or grey scuff pad) only if nibs; final coat not sandedrecommended
- Technique
- Shake 1–2 min after the ball starts rattling; test-spray off the work; move parallel to the surface, start and stop the spray off the edge; ~50 % overlap; keep the can upright.recommended
Shake the can before use. Don't spray onto cold or hot surfaces. Spray from 15–25 cm. When finished, turn the can upside down and spray until clear to purge the cap. dealer
Process and compatibility
- Substrate preparation
- Wood or old finish clean, dry and degreased; scuff the old finish with P320–P400; sand repairs (filler, wax-stick) flush; prime bare wood first.recommended
- Goes over
- ATS20 / PPS20 / APL20 / APL R1015 M
- Goes under
- CQS70 / ATL70 SM
- Sanding
- Sand only after full dry (≥ 3–4 h, preferably overnight), P400–P600recommended
- Temperature and humidity
- 15–25 °C, RH ≤ 70 %; can and workpiece at room temperaturerecommended
- Don'ts
- don't spray onto cold or hot surfaces
- don't add hardeners or thinners
- don't lay it on heavy in one pass
- don't sand or polish the final 30-gloss coat
Storage
- Storage temperature
- +5…+30 °C, away from heat and sun, never above 50 °Crecommended
- Packaging
- 400 ml aerosol candealer
Safety: Pressurised container, extremely flammable contents. Keep below 50 °C, don't pierce or burn even when empty. Use with good ventilation, organic-vapour (A) respirator, away from ignition sources.
Sources
Value tags: “official”, “dealer”, “catalog”, “schedule” are Technocolor data; “workshop” is from our own datasheets; “recommended” is our engineering estimate (hover to see the reasoning).
- dealer page: description, properties, use, 80–100 g/m², 15–25 cm, 30 gloss, full dry 3–4 h, 400 ml, RAL1015
- APL70 SM white dealer page: touch dry 10–20 min, two-cap kit, hiding
- APL70 R1015 M dealer page: same text, 20 gloss — confirms colour series
Not covered by the sources
- no official t-color.ru page or TDS/SDS for APL70 (web TDS search not possible this session — search budget exhausted)
- solids, density, VOC, propellant not published
- touch-dry time not on the R1015 SM page (taken from APL70 SM white)
- recoat window, sanding time, hardness, chemical resistance not published
- shelf life not published
- officially approved substrates/primers and top coats not published
- not referenced in any official finishing schedule
- main catalog (150 g/m², G = 75 gloss) and dealer/leaflet (80–100 g/m², G = 70 gloss) disagree