AcrylicLacquerGloss: 30 GU 60°

ATL70 SM

Acrylic touch-up lacquer, clear, aerosol can (30 gloss)

Ready-to-use clear acrylic lacquer in an aerosol can for touch-up and restoration, 30 gloss. High clarity, non-yellowing, fast drying; no overspray halo and lays down an even film. Comes with two actuator caps — a no-halo cap for spot repairs and blending, and a wider cap for first-coat lacquering.

Any wood species
First lacquer coat on small areas
Re-coating after defect repair (chips, scratches, after filler/wax/CTU marker retouching)
Evening out sheen after a spot repair on satin finishes

Scan to open this page on a phone

Download:PNG SVG

Single-component product: no mixing needed — use as supplied (see application below).

Ask about ATL70 SM

Answers are based on the ATL70 SM data and the products it mixes with.

Characteristics

Gloss: 30 GU 60°dealer
Drying · Touch-dry: 10–20 mindealer
Drying · Full cure: 3–4 hdealer
Drying · Dust-free: 5–10 minrecommended
Drying · Sand or stack: ≥ 4 (overnight preferred) hrecommended
Drying · Conditions: 20 °C
Pot life: n/a — one-component aerosol, no mixingdealer
Lightfastness: non-yellowingdealer

Colours

clear · Clear

Application

Conventional spray

Device: aerosol can (2 interchangeable actuator caps)
Nozzle: built-in actuator (~0.3–0.5 mm orifice equivalent); no-halo cap for spot repair/blending, wide-fan cap for first coatsrecommended
Pressure · fluid: not adjustable — can internal pressure (typically ~3–5 bar at 20 °C)recommended
Pressure · air: n/arecommended
Gun distance: 15–25dealer
Consumption: 80–100 g/m²dealer
Wet film: ~30–60 per pass µmrecommended
Coats: 2–3 thin crossing passesrecommended
Flash-off: 5–10 minrecommended
Recoat: 10–20 min between passes; after full dry (≥ 3–4 h) for sanding or overcoatingrecommended
Sanding between coats: Not needed between passes; if dust nibs, denib after full dry with P800–P1000 or a grey pad, then one light final passrecommended

Shake the can before use (1–2 min after the ball starts rattling). Do not spray onto cold or hot surfaces. Hold 15–25 cm away, keep the can parallel to the surface, start and stop the spray off the edge of the repair. After use turn the can upside down and spray until only clear gas comes out to clear the nozzle. dealer

Process and compatibility

Substrate preparation: Clean, dry and degreased. Level the repaired spot (filler, wax, retouch), sand P320–P400, de-dust. Scuff the surrounding old finish lightly with a grey pad so the touch-up keys in.recommended
Sanding: Repair area P320–P400 before; no sanding of the final coatrecommended
Don'ts: Do not spray onto cold or hot surfaces
Do not add hardener or thinner
Do not sand or polish the final 30-gloss coat — it burnishes to shiny patches
Do not lay it on heavy — sags and uneven sheen

Storage

Packaging: 400 мл аэрозольный баллонdealer
Storage temperature: 5–25 °C, away from heat and sun, never above 50 °Crecommended

Safety: Pressurized, flammable aerosol. Do not heat above 50 °C, pierce or burn, even when empty. Use with ventilation and an organic-vapour (A) respirator, away from flames and sparks.

Sources

Value tags: “official”, “dealer”, “catalog”, “schedule” are Technocolor data; “workshop” is from our own datasheets; “recommended” is our engineering estimate (hover to see the reasoning).

Not covered by the sources

No official t-color.ru page and no TDS/SDS found (dealer lakokraska31 search gave nothing usable)
Solids, viscosity, density not published (not meaningful for a ready aerosol, but unknown)
Dust-free and recoat times not published (only touch 10–20 min, full 3–4 h)
Consumption conflict: catalog 150 g/m² vs dealer 80–100 g/m²
Shelf life and storage temperature not published
Compatibility over other Technocolor systems not stated by manufacturer
No finishing schedule (information/technology) uses ATL70
Hardness, chemical resistance, elasticity not published; lightfastness only qualitative (non-yellowing)