APL R9016 M
Acrylic enamel, Traffic White RAL 9016 (20 gloss)
Two-pack acrylic enamel (cured with AC40), factory-tinted to Traffic White RAL 9016, 20 gloss. Tough, flows out well in thin coats, flexible, and shows the open grain nicely. Used as a top coat on its own or as the ground colour under patina.
- kitchen furniture
- bathroom furniture
- cabinets and doors
- ground coat under patina (decapé)
Mix calculator
Ask about APL R9016 M
Answers are based on the APL R9016 M data and the products it mixes with.
Mixing matrix
- AC40Hardener% by weight: 10–20 (typ. 15) %catalog% by volume: 15–25 %recommended
always — it's a 2K system
Go towards 20 % for kitchen/bath resistance, towards 10 % for a bit more flex.
- S50Thinner% by weight: 30–40 %catalog% by volume: 40–50 %recommended
default: universal thinner, normal conditions, verticals
S50 is normal-evaporation, the default. Doesn't change cure time.
- S80Thinner% by weight: 30–40 %catalog% by volume: 40–50 %recommended
above ~25 °C, large flat panels
S80 is slow — better levelling but more dust pick-up and sag risk. Doesn't change cure time.
- S50Thinner% by weight: 40–50 %recommended
open-pored timber (oak, ash) — better colour and pore definition; apply 200–250 g/m²
- AC40Hardener% by weight: 20 %schedule
schedule 'Oak kitchen fronts, decapé effect (acrylic)', step 7 — 'APL20 (RAL,NCS)'
Schedule writes 'C40' — read AC40. Schedule is for tinted APL20; APL R9016 M is the same enamel ready-tinted.
- S50Thinner% by weight: 30 %schedule
same decapé schedule, step 7
| Role | Material | % by weight | % by volume | When |
|---|---|---|---|---|
| Hardener | AC40 | 10–20 (typ. 15) %catalog | 15–25 %recommended | always — it's a 2K systemGo towards 20 % for kitchen/bath resistance, towards 10 % for a bit more flex. |
| Thinner | S50 | 30–40 %catalog | 40–50 %recommended | default: universal thinner, normal conditions, verticalsS50 is normal-evaporation, the default. Doesn't change cure time. |
| Thinner | S80 | 30–40 %catalog | 40–50 %recommended | above ~25 °C, large flat panelsS80 is slow — better levelling but more dust pick-up and sag risk. Doesn't change cure time. |
| Thinner | S50 | 40–50 %recommended | — | open-pored timber (oak, ash) — better colour and pore definition; apply 200–250 g/m² |
| Hardener | AC40 | 20 %schedule | — | schedule 'Oak kitchen fronts, decapé effect (acrylic)', step 7 — 'APL20 (RAL,NCS)'Schedule writes 'C40' — read AC40. Schedule is for tinted APL20; APL R9016 M is the same enamel ready-tinted. |
| Thinner | S50 | 30 %schedule | — | same decapé schedule, step 7 |
Percentages are per 100 parts of component A.
Characteristics
- Solids
- 53catalog
- Viscosity
- 85 ± 10 srecommended
- Density
- ≈1.25–1.35 g/cm³recommended
- Gloss
- 20 GU 60°catalog
- Pot life
- 6recommended
- Drying · Touch-dry
- 20recommended
- Drying · Full cure
- 8recommended
- Drying · Forced drying (h)
- 1.5schedule
- Drying · Sand or stack
- ≥ 8 (overnight preferred)recommended
- Drying · Conditions
- 20 °C
- Lightfastness
- non-yellowingrecommended
- Chemical resistance
- excellent durabilitycatalog
- Elasticity
- flexiblecatalog
- Flow
- good flow in thin coatscatalog
- Thixotropy
- norecommended
Colours
- RAL 9016 · Traffic White
Application
HVLP
- Consumption
- 150catalog
- Spray viscosity
- 18–22 s DIN4/ВЗ-4recommended
- Nozzle
- 1.7–1.8 mmrecommended
- Pressure · fluid
- gravity cup; pressure pot 0.8–1.2 barrecommended
- Pressure · air · Inlet pressure
- 2–2.5 bar (trigger pulled)
- Pressure · air · Cap
- 0.7 bar
- Pressure · air · Why ru
- Соответствие HVLP; настройка владельца для ATL50 (2,0–2,2 бар) плюс немного больше для более густой белой.
- Wet film
- 115–130 µmrecommended
- Coats
- 1–2 (2 for full hide of white on primer; 1 under patina)recommended
- Flash-off
- 5–10 minrecommended
- Recoat
- after 20–30 min (touch dry) wet-on-dry without sanding, or after 8 h full dry with a scuffrecommended
- Sanding between coats
- P320–P400 or grey pad after full dry; denib onlyrecommended
- Gun distance
- 15–20recommended
HVLP, 1.7–1.8 mm tip, 2.0–2.5 bar inlet with trigger pulled, ≤0.7 bar at the cap, fan wide open, 50–75 % overlap, 15–20 cm.
Conventional spray
- Consumption
- 150catalog
- Nozzle
- 1.6–1.8 mmrecommended
- Pressure · air
- 3–4 barrecommended
Spray application per catalog. Transfer efficiency up to ~40 % (methods page).
Airmix (air-assisted airless)
- Nozzle
- 09–11 thou (0.23–0.28 mm), 40–50° fanrecommended
- Pressure · fluid
- 12–20 barrecommended
- Pressure · air
- 1–2 barrecommended
Airmix beats airless for finish coats (methods page).
Airless
- Nozzle
- 11–13 thou (0.28–0.33 mm)recommended
- Pressure · fluid
- 120–160 barrecommended
Not ideal for a finish coat — coarser atomisation; prefer airmix.
Electrostatic
- Why ru
- Страница методов: любая система распыления может работать в электростатике; подтверждения для конкретного продукта нет.
Works with any spray method — chairs, legs; check the mix conductivity first.
Process and compatibility
- Substrate preparation
- грунт APS20 (+AC40 20 %, S50 40 %), 150 г/м², сушка 30–35 °C 1,5 ч, шлифовка P240–P320 / маты К120 по профилюschedule
- Goes over
- APS20
- Goes under
- CQS / ATL20
- Sanding
- primer P240–P320 (schedule); enamel P320–P400 after full dry if recoatingrecommended
- Temperature and humidity
- 18–25 °C, RH 50–70 %; forced dry 30–35 °Crecommended
- Don'ts
- don't eyeball AC40 — weigh it
- don't use the mix past ~6 h pot life
- don't brush — spray only
- don't sand or polish the final 20-gloss coat — it goes patchy
Storage
- Packaging
- 1 кг,5 кг,25 кгrecommended
Safety: Flammable solvent-borne coating. AC40 is listed in the catalog as an aliphatic hardener for acrylics, so most likely aliphatic isocyanate (HDI) based. Spray in an extracted booth, A2P3 respirator (or air-fed), nitrile gloves. No naked flames.
Used in finishing systems
Sources
Value tags: “official”, “dealer”, “catalog”, “schedule” are Technocolor data; “workshop” is from our own datasheets; “recommended” is our engineering estimate (hover to see the reasoning).
- official page — exists, title only, no data
- dealer search — no APL R9016 M card; only APL70 RAL9016 M aerosol and PPL R9016 M
- decapé schedule step 7: APL20 (RAL,NCS) + C40 20 % + S50 30 %, 150 g/m², 30–35 °C 1.5 h
- application methods page
- sibling dealer card: viscosity 85±10 s, pot life 6 h, touch 20 min, full 8 h, gloss 20±3, v/v ratios, oak/ash note, packaging
- sibling dealer card (same figures)
- sibling dealer card (same figures)
- APL70 R9016 M aerosol (different product, same colour)
- official APL20 M page (white base, same chemistry): AC40 10–20 % w/w / 15–25 % v/v, S50/S80 30–40 % w/w / 40–50 % v/v, non-yellowing
Not covered by the sources
- official page has no data (title only)
- no dealer card for APL R9016 M — viscosity, pot life, touch/full dry and gloss tolerance are carried over from sibling APL RAL dealer cards (marked derived)
- % by volume for AC40 and S50/S80 (catalog gives weight only; v/v carried over from APL20 M official page / sibling cards, marked derived)
- density (not published)
- dust-free time
- sanding time
- hardness
- shelf life / storage temperature
- packaging and price for this colour
- official TDS/SDS PDF not found (web search budget exhausted)
- AC40 chemistry: catalog says aliphatic; isocyanate type (HDI) assumed, no SDS
- all spray-equipment parameters are derived