CPH64
CPH64 Cherry wood impregnation (waterborne, exterior)
Cherry-coloured waterborne impregnation for exterior timber. Protects wood from the elements — temperature swings, moisture and insects — and gives it a decorative cherry tone. Even colour, strong protection against fungi, mould and wood pests, high lightfastness.
- window frames
- door frames
- cottages and timber houses
- balconies
- fences, gazebos and other exterior timber structures
Mix calculator
Ratio 100 : 0.0
| Component | Weigh out |
|---|---|
| CPH64part A | 500 g |
| waterThinner | 0.0 g |
| Total | 500 g |
Covers roughly 7.14 m² at 70 g/m².
Ask about CPH64
Answers are based on the CPH64 data and the products it mixes with.
Mixing matrix
- waterThinner% by weight: 0–5 %recommended
Only if needed (thickened product, topping up a dip tank).
Never thin with solvent thinners (S50/S80 etc.) — this is a waterborne product. For a lighter cherry, cut it with the clear CPH6 impregnation rather than water.
- CPH6Additive% by weight: 0–100 %recommended
When a lighter, more transparent cherry tone is wanted.
Always test on a sample of the same species.
| Role | Material | % by weight | % by volume | When |
|---|---|---|---|---|
| Thinner | water | 0–5 %recommended | — | Only if needed (thickened product, topping up a dip tank).Never thin with solvent thinners (S50/S80 etc.) — this is a waterborne product. For a lighter cherry, cut it with the clear CPH6 impregnation rather than water. |
| Additive | CPH6 | 0–100 %recommended | — | When a lighter, more transparent cherry tone is wanted.Always test on a sample of the same species. |
Percentages are per 100 parts of component A.
Characteristics
- Base
- waterborne (ВР)catalog
- Components
- 1K, ready to userecommended
- Biocide
- protects against fungi, mould and wood pestsofficial
- Colour uniformity
- good (хорошая однородность цвета)official
- Lightfastness
- high (высокая светоустойчивость)official
- Consumption
- 60–80 g/m²official
Colours
- CPH64 · cherry
Application
HVLP
- Consumption
- 60–80 g/m²official
- Nozzle
- 1–1.3 mmrecommended
- Pressure · air
- 1.5–2 bar (gun inlet, trigger pulled)recommended
- Pressure · fluid
- 0.2–0.5 bar (pressure pot, if used)recommended
- Spray viscosity
- as suppliedrecommended
- Coats
- 1–2 coatsrecommended
- Flash-off
- 30–60 minrecommended
- Recoat
- 2–4 h before topcoat (lazure / WB lacquer)recommended
Lay on an even wet coat with overlap, no puddles or runs — otherwise you get colour patches; flood end grain well. Use a WB-rated (stainless) gun and hoses. Stir before use — the pigment settles.
Airmix (air-assisted airless)
- Consumption
- 60–80 g/m²official
- Nozzle
- 0.18–0.23 mm (007–009 thou), 20–40° fanrecommended
- Pressure · fluid
- 40–70 barrecommended
- Pressure · air
- 0.8–1.5 barrecommended
Dipping
- Consumption
- 60–80 g/m²official
Dipping gives good penetration of the colour into the wood; it is the usual way to apply a protective tinted impregnation in window production. Let the part drain fully, then dry. Keep the tank stirred.
Brush
- Consumption
- 60–80 g/m²official
Synthetic-bristle brush, work along the grain and brush out surplus so there are no dark laps.
Flow coating
- Consumption
- 60–80 g/m²dealer
Flow coating is listed by the dealer (not on the official page). The methods page says it is mainly used for stains.
Process and compatibility
- Substrate preparation
- Dry, clean, dust-free timber with no old film coatings; wood moisture 12–15 %; final sanding P120–P150 (coarser rather than finer outdoors, so it soaks in).recommended
- Goes over
- bare wood
- Sanding
- The impregnation raises the grain — denib lightly with P180–P220 before lazure/lacquer, carefully so you do not cut through the colour on edges.recommended
- Temperature and humidity
- Apply at +10…+30 °C, RH up to 80 %; not in direct sun, rain or on wet timber.recommended
- Don'ts
- Do not thin with solvent thinners.
- Do not apply over old lacquer or paint — it has to soak into bare wood.
- Do not let the product freeze.
- Not for living interiors (use the biocide-free CPH6xx lazures indoors).
Storage
- Packaging
- 1 kg,5 kgdealer
- Storage temperature
- +5…+30 °C, do not freezerecommended
Safety: Protective impregnation with fungicidal/insecticidal action: wear gloves and goggles, and a respirator when spraying; not for interiors or food-contact surfaces.
Sources
Value tags: “official”, “dealer”, “catalog”, “schedule” are Technocolor data; “workshop” is from our own datasheets; “recommended” is our engineering estimate (hover to see the reasoning).
- official page: properties (colour uniformity, protection vs fungi/mould/pests, lightfastness), methods spray/dip/brush 60–80 g/m²
- dealer page: description, application area, methods incl. flow coating 60–80 g/m², packaging 1/5 kg, 710 ₽/kg; no technical characteristics block
- clear base of the same line (CPH6)
- methods page: dipping used for protective tinted impregnation in window production; flow coating mainly for stains
Not covered by the sources
- solids_pct
- viscosity (cup/seconds)
- density
- drying times (dust-free/touch/recoat/full) — not published by official site, dealer or catalogues
- active biocide type/concentration
- shelf life
- official storage temperature
- SDS / ТДС PDF — none found (dealer has no 'Все технические характеристики' block; woodonline/lakokraska31 have no listing; web-search budget exhausted this session)
- official confirmation of topcoat compatibility (catalog names only clear CPH6 as lazure pre-treatment)
- official dilution/blending ratio with CPH6
- not used in any of the 11 official finishing schedules (all interior)