HTL61 SM
HTL61 SM waterborne exterior lacquer, 'Grain' (Zerno) tint, 30 gloss
One-pack waterborne acrylic exterior lacquer, semi-matt (30 gloss), factory-tinted 'Grain' on the clear HTL60 SM converter base. Highly elastic, light- and weather-resistant; protects timber from UV, water, dust and dirt. Ready to use — just stir. No harmful solvents, practically odourless, dries fast. Good for new work and for refreshing previously finished surfaces. Spray, brush or roller, 2–3 coats.
- windows
- facades of country houses and dachas
- exterior doors
- decks/terraces and gazebos
- garden furniture
- fences
- refinishing previously coated exterior surfaces
Mix calculator
Ratio 100 : 5.0
| Component | Weigh out |
|---|---|
| HTL61 SMpart A | 476 g |
| WATERThinner | 23.8 g |
| Total | 500 g |
Covers roughly 2.50 m² at 200 g/m².
Pot life of the mix: n/a.
Ask about HTL61 SM
Answers are based on the HTL61 SM data and the products it mixes with.
Mixing matrix
- WATERThinner% by weight: 0–10 %catalog% by volume: 0–10 %dealer
Only to trim working viscosity: 5–10 % for spraying, 0–5 % for brush/roller.
No hardener. Clean (ideally demineralised) water only — never S50/S80. Don't exceed 10 %: less build and durability, weaker tint, sags.
| Role | Material | % by weight | % by volume | When |
|---|---|---|---|---|
| Thinner | WATER | 0–10 %catalog | 0–10 %dealer | Only to trim working viscosity: 5–10 % for spraying, 0–5 % for brush/roller.No hardener. Clean (ideally demineralised) water only — never S50/S80. Don't exceed 10 %: less build and durability, weaker tint, sags. |
Percentages are per 100 parts of component A.
Characteristics
- Solids
- 44 ± 1 %dealer
- Viscosity
- 70 ± 5 sdealer
- Density
- 1.05 g/cm³recommended
- Gloss
- 30 ± 3 GU (60°)dealer
- Pot life
- n/arecommended
- Drying · Dust-free
- 15–20 minrecommended
- Drying · Touch-dry
- 30 mindealer
- Drying · Sand or stack
- 2–4 hrecommended
- Drying · Full cure
- 24 hdealer
- Drying · Conditions
- 20 °C
- Hardness
- moderate (elastic rather than hard)recommended
- Lightfastness
- light- and weather-resistant (catalog); protects against UV (dealer)catalog
- Service life
- for lacquer on the HTL60 base — at least 10 years outdoors in a temperate climateofficial
- Chemical resistance
- not stated — treat as low/moderaterecommended
- Elasticity
- highcatalog
- Weather resistance
- good weather resistance; moisture-resistantdealer
- Adhesion
- high adhesion, doesn't peel over timedealer
- Odour / VOC
- waterborne, no harmful solvents, practically odourlessdealer
- Thixotropy
- norecommended
Colours
- HTL61 SM · 'Grain' (Zerno) — factory tint on the HTL60 SM base
Application
HVLP
- Consumption
- 200 g/m²dealer
- Nozzle
- 1.7–2 mmrecommended
- Pressure · air
- 2–2.5 barrecommended
- Pressure · fluid
- 0.8–1.5 barrecommended
- Spray viscosity
- 30–45 s DIN4/CF-4 at 20 °Crecommended
- Wet film
- 140–190 µmrecommended
- Coats
- 2–3 coatsdealer
- Flash-off
- 10–20 minrecommended
- Recoat
- 2–4 hrecommended
- Sanding between coats
- P240–P320recommended
Flush equipment with water before and after use (dealer). The rest is derived: 15–20 cm distance, 50 % overlap, fan fully open; strain; stir thoroughly (tinted — pigment settles); build the 200 g/m² in two cross passes, not one heavy one.
Conventional spray
- Consumption
- 200 g/m²catalog
- Nozzle
- 1.8–2 mmrecommended
- Pressure · air
- 3–3.5 barrecommended
- Spray viscosity
- 30–45 s DIN4/CF-4 at 20 °Crecommended
- Coats
- 2–3 coatsdealer
Air spray is the catalog method. Transfer efficiency is up to 40 % (methods page) — allow for overspray.
Airmix (air-assisted airless)
- Nozzle
- 0.23–0.33 mmrecommended
- Pressure · fluid
- 40–80 barrecommended
- Pressure · air
- 1–2 barofficial
- Spray viscosity
- 0–5 % water addedrecommended
- Coats
- 2–3 coatsdealer
Best for production windows and doors (dealer: "for painting windows"; official methods page: Airmix suits finish coats better than Airless).
Airless
- Nozzle
- 0.28–0.38 mmrecommended
- Pressure · fluid
- 100–160 barrecommended
- Spray viscosity
- 0–5 % water addedrecommended
- Coats
- 2–3 coatsdealer
For big areas — facades, fences. Finish quality on joinery is below Airmix.
Brush
- Consumption
- 200 g/m²catalog
- Spray viscosity
- 0–5 % water addedrecommended
- Coats
- 2–3 coatsdealer
- Recoat
- 2–4 hrecommended
Synthetic brush for waterborne; lay off along the grain and don't rework a drying edge — tinted lacquer shows laps and blotches.
Roller
- Consumption
- 150–200 g/m²recommended
- Coats
- 2–3 coatsdealer
Method listed by the dealer ("brush, roller or sprayer"). Short-nap/velour roller for waterborne lacquer; tip off with a brush along the grain (derived).
Process and compatibility
- Substrate preparation · Wood moisture
- 8–14 %official
- Substrate preparation · Antiseptic first
- Pre-treat with an antiseptic for extra protection against mould, fungus and insectsdealer
- Substrate preparation · Restoration
- Suitable for new work and for refinishing previously coated surfacesdealer
- Substrate preparation · Preparation
- Dry, clean, dust-free wood; sand P150–P180 (end-grain P180–P220); degrease resinous spots; old finish — remove anything flaking, scuff the rest at P180–P240 and test adhesion on a patch.recommended
- Sister products
- HTL60 SM,HPL60 SM,HTS30catalog
- Sanding
- After the first coat P240–P280 (raised grain), between later coats P320; don't sand the finish coat.recommended
- Temperature and humidity
- Apply above +15 °C and below 70 % RHdealer
- Don'ts
- don't apply below +15 °C or above 70 % RH (dealer)
- don't thin with S50/S80 — water only, max 10 %
- don't add AC/PC hardeners — it's one-pack (derived)
- don't finish wet timber, before rain or in direct sun (derived)
- don't let it freeze (derived)
- don't apply over oil/wax without stripping (derived)
- don't lay the full 200 g/m² in one heavy coat on verticals — it sags (derived)
- Mixing
- Ready to use — just stirdealer
- Equipment cleaning
- Flush equipment with water before and after usedealer
Storage
- Packaging
- 1,5,10 kgdealer
- Storage temperature
- 5–30 °Crecommended
Safety: Waterborne, no harmful solvents, practically odourless (dealer). When spraying wear gloves and a particulate mask; don't pour leftovers down the drain (derived — no SDS published).
Sources
Value tags: “official”, “dealer”, “catalog”, “schedule” are Technocolor data; “workshop” is from our own datasheets; “recommended” is our engineering estimate (hover to see the reasoning).
- dealer product page: description, uses, 2–3 coats, brush/roller/spray, antiseptic pre-treatment, water 0–10/0–10, 200 g/m², +15 °C/<70 % RH, gloss 30±3, solids 44±1 %, viscosity 70±5 s CF-4, touch 30 min, full 24 h, 1/5/10 kg, 845 ₽/kg
- woodonline dealer page: confirms 70±5 s CF-4, water 0–10/0–10, 200 g/m², windows/exterior; ТДС on request
- official news: HTL60-based coating service life ≥10 years outdoors (temperate climate)
- base product HTL60 SM dealer page (same 44±1 %, 70±5 s, 30/24 h figures)
- official application methods (air spray transfer ≤40 %, Airmix ≤20 bar + 1–2 bar air, airless ≤200 bar)
- glossary: wood moisture 8–14 %, RH 40–75 %
- characteristic definitions (vocabulary)
Not covered by the sources
- No official t-color.ru product page for HTL61 SM
- No Technocolor ТДС/technical data sheet PDF found (woodonline: «ТДС ... по запросу»); web search budget exhausted this session
- Colour 'Зерно' has no published RAL/NCS/swatch reference
- density not published (derived)
- dust-free and recoat/sand times not published (derived)
- spray viscosity of the thinned mix not published (derived)
- consumption per coat vs total not stated (200 g/m² read as per coat)
- hardness, chemical resistance, abrasion values not published
- shelf life not published
- storage temperature not published (derived)
- compatible impregnation/primer not officially named (antiseptic recommended generically; CPH6/CTH100/HTS30 derived)
- not used in any official finishing schedule (information/technology)
- 10-year service life is stated officially for HTL60, applied here by inheritance
- Airmix/airless pressures and tips are derived; official methods page gives only generic ceilings (Airmix ≤20 bar + 1–2 bar air, airless ≤200 bar)