APL70 R9016 M
Acrylic aerosol enamel, RAL 9016 Traffic White (20 gloss)
Acrylic enamel in a 400 ml spray can, tinted RAL 9016 Traffic White, 20 gloss. Ready to use — nothing to mix or thin. Good hide, rich colour, no overspray halo at the edge of the repair, fast drying. For touching up and repairing white fronts and furniture, small parts, and blending the sheen after a repair.
- any wood species
- first finish on small surfaces
- restoring the finish after a defect repair
- evening out the sheen
Single-component product: no mixing needed — use as supplied (see application below).
Ask about APL70 R9016 M
Answers are based on the APL70 R9016 M data and the products it mixes with.
Characteristics
- Components
- 1K, ready to use — no hardener, no thinnerdealer
- Gloss
- 20 глосс / gloss unitsdealer
- Drying · Fast drying
- fast dryingcatalog
- Drying · Sand or stack
- sand/stack no earlier than full dry (≥ 4 h at 20 °C); leave fronts overnight before packingrecommended
- Drying · Conditions
- 20 °C
- Volume (ml)
- 400dealer
- Hiding power
- high hiding powercatalog
Colours
- RAL 9016 · Traffic White
Application
Aerosol
- Method (fallback)
- conventional_spray
- Device
- 400 ml can with 2 actuators: halo-free spot repair tip and a wider tip for first coatscatalog
- Nozzle
- fixed can actuator: narrow halo-free tip for spot repairs, wide tip for panelsrecommended
- Pressure · Can
- factory can pressure; keep can and part at 18–25 °C, warm a cold can in water ≤ 40 °Crecommended
- Coats
- 2–3 light passes rather than one heavyrecommended
- Recoat
- wet-on-wet after 5–10 min, or after full dry (3–4 h) with a light scuffrecommended
- Sanding between coats
- grey pad or P600–P800, denib onlyrecommended
- Technique
- shake the can before use (ball rattling, ≥ 1–2 min); don't spray onto cold or hot surfaces; spray from 15–25 cm; when done, turn the can upside down and blow the nozzle cleardealer
Start and stop each pass off the part, keep the can parallel to the surface; for spot repairs use the narrow tip and feather the edge with a light mist.
Process and compatibility
- Substrate preparation
- чистая, сухая, обезжиренная поверхность; старое покрытие заматировать P320–P400 / серым скотч-брайтом, сколы зашпатлевать и зашлифовать заподлицо, голое дерево сначала загрунтовать / clean, dry, degreased; scuff the old finish P320–P400 or grey pad, fill and flush-sand chips, prime bare wood firstrecommended
- Goes under
- ATL70 M
- Sanding
- перед окраской P320–P400; между слоями — только обеспыливание P600–P800; финиш 20 гл не шлифовать и не полироватьrecommended
- Temperature and humidity
- 18–25 °C, отн. влажность ≤ 70 %, деталь и баллон при комнатной температуреrecommended
- Don'ts
- don't add hardener or thinner
- don't spray onto cold or hot surfaces
- don't lay it on heavy — it'll run
- don't skip blowing the nozzle clear afterwards — it'll clog
Storage
- Packaging
- 400 ml aerosol candealer
- Custom tint
- tinted to any RAL/NCS colour to order, min. 24 canscatalog
- Storage temperature
- +5…+25 °C, вдали от нагревателей и солнца, не выше +50 °Crecommended
Safety: Pressurised container, flammable contents. Don't heat above 50 °C, don't pierce or burn even when empty. Use with ventilation or extraction, no naked flames, A2P2 respirator and gloves.
Sources
Value tags: “official”, “dealer”, “catalog”, “schedule” are Technocolor data; “workshop” is from our own datasheets; “recommended” is our engineering estimate (hover to see the reasoning).
- dealer: description, properties, uses, 80–100 g/m², 15–25 cm, shake/purge notes, 20 gloss, full dry 3–4 h at 20 °C, 400 ml, colour RAL9016, 821 ₽
- dealer APL70 M (white base): hide, 2 nozzles in kit, same data
- dealer search: all APL70 variants (g, m, sm, um, r9003_m, ral1015_m, ral1015_sm, ral9001_m, ral9010_m, ral9016_m) — same characteristic set
- characteristics vocabulary (gloss definition)
- application methods page
Not covered by the sources
- no official page / no TDS or SDS found (web search budget exhausted; dealer + catalogs only)
- solids %
- density
- viscosity (n/a for aerosol)
- pot life (n/a, 1K)
- dust-free and touch-dry times (only full dry 3–4 h published)
- hardness
- lightfastness / yellowing
- chemical resistance
- elasticity
- binder chemistry (1K acrylic assumed)
- shelf life
- consumption conflicts: dealer 80–100 g/m², 2022 catalog 60–80 g/m², 2025 catalog 150 g/m²
- all actuator/pressure guidance is derived (aerosol, no adjustable equipment)
- storage temperature (only derived generic aerosol rule)
- gloss measuring geometry