ATL70 M
Acrylic touch-up lacquer, matt (20 GU), 400 ml aerosol can
Acrylic lacquer in a spray can for repair and touch-up: water-clear, non-yellowing, fast drying. Ready to use, no overspray halo, lays down evenly. Comes with 2 actuator caps — one for halo-free blending, one for straight coating.
- Any wood species
- Clear-coating small areas
- Restoring the finish after a repair
- Matching sheen on a repaired spot
Single-component product: no mixing needed — use as supplied (see application below).
Ask about ATL70 M
Answers are based on the ATL70 M data and the products it mixes with.
Characteristics
- Gloss
- 20 GU (глосс)dealer
- Drying · Touch-dry
- 10–20dealer
- Drying · Full cure
- 3–4dealer
- Drying · Conditions
- при 20 °C / at 20 °C
- Lightfastness
- non-yellowingdealer
- Volume
- 400 mldealer
- Components
- ready to use, nothing added (1K is inferred)catalog
Application
Aerosol
- Method (fallback)
- conventional_spray
- Consumption
- 80–100dealer
- Gun distance
- 15–25dealer
- Nozzle
- not adjustable — 2 supplied actuators (halo-free for blending, standard for straight coating)recommended
- Pressure
- not adjustable (can pressure); bring the can to ~20 °Crecommended
- Sanding between coats
- no sanding between coats; for nibs wait 3–4 h, denib P800–P1000 or a grey pad, then a final coatrecommended
- Technique
- Shake 1–2 min, keep the can upright, move at an even pace, start and stop off the part, ~50 % overlap. To blend into old finish use the halo-free cap and a light misting last pass over the edge. Check sheen under raking light next to the old finish; if it's off, step to the neighbouring sheen in the line (UM 10 / SM 30).recommended
Shake the can before use. Don't spray onto cold or hot surfaces. Spray from 15–25 cm. After use, turn the can upside down and spray until the nozzle runs clear. dealer
Process and compatibility
- Substrate preparation
- Fill/repair the defect, sand P320–P400, key the surrounding old finish with P600–P800 or a grey pad, de-dust and degrease. Seal bare wood first (a light coat of the same lacquer, or ATS20 acrylic sealer).recommended
- Sanding
- don't sand or polish the final matt coatrecommended
- Don'ts
- Don't spray onto cold or hot surfaces
- Don't skip shaking the can
- Don't put the can away without clearing the nozzle
Storage
- Packaging
- 400 ml aerosol can + 2 capsdealer
Sources
Value tags: “official”, “dealer”, “catalog”, “schedule” are Technocolor data; “workshop” is from our own datasheets; “recommended” is our engineering estimate (hover to see the reasoning).
- описание, свойства, применение, расход 80–100 г/м², дистанция 15–25 см, блеск 20, на ощупь 10–20 мин, полное 3–4 ч, 400 мл
- состав линейки ATL70 у дилера (DM/UM/M/SM/G); страницы сестёр подтверждают те же сушку/расход
Not covered by the sources
- solids_pct (не опубликовано)
- viscosity (не применимо к аэрозолю / не опубликовано)
- density
- dust_free_min
- stack_or_sand_h
- hardness, chemical_resistance, elasticity
- shelf_life
- официальный ТДС/SDS — веб-поиск исчерпан (лимит сессии), не найден
- wet_film_um
- расход: дилер 80–100 г/м² vs каталог 150 г/м² — не согласовано
- не используется ни в одной официальной схеме отделки (information/technology)