TSE014-05
TSE014-05 Crackle effect medium, neutral (craquelure)
Neutral (uncoloured) medium for a decorative crackle / craquelure finish. Sprayed over an enamel that has been sealed with a clear lacquer (nitro LEC19812 or water-based XGC32), optionally tinted with CS pigment pastes. As it dries the film breaks up into cracks that show the colour underneath; once the crack pattern has fully developed it is sealed with a clear topcoat (ATL500, LDA401).
- decorative antique-look furniture door finishes (craquelure)
- 'Mosaic' effect — coarse cracking of a coloured layer over an enamel
- two-tone effects: tinted crackle over a contrasting enamel
Mix calculator
Ratio 100 :
| Component | Weigh out |
|---|---|
| TSE014-05part A | 500 g |
| Total | 500 g |
Covers roughly 3.33 m² at 150 g/m².
Ask about TSE014-05
Answers are based on the TSE014-05 data and the products it mixes with.
Mixing matrix
- TSE3Additive% by weight: 5 %catalog
first crackle coat in the 'Craquelure' system (over LEC19812)
TSE3's function is not stated anywhere in the sources (probably a crackle modifier); no official page or dealer listing exists.
- CS70001Additive% by weight: 5 %catalog
second (coloured) crackle coat in the 'Craquelure' system, over the second LEC19812 coat
CS70001 is a CS-series pigment paste; any CS colour may be used ('tinted with CS pigment pastes').
- CSAdditive
tinting to the required colour / RAL ('Mosaic' effect)
Recommendation: keep paste at ~5–10 % max or the crack pattern changes — always do a test panel.
| Role | Material | % by weight | % by volume | When |
|---|---|---|---|---|
| Additive | TSE3 | 5 %catalog | — | first crackle coat in the 'Craquelure' system (over LEC19812)TSE3's function is not stated anywhere in the sources (probably a crackle modifier); no official page or dealer listing exists. |
| Additive | CS70001 | 5 %catalog | — | second (coloured) crackle coat in the 'Craquelure' system, over the second LEC19812 coatCS70001 is a CS-series pigment paste; any CS colour may be used ('tinted with CS pigment pastes'). |
| Additive | CS | — | — | tinting to the required colour / RAL ('Mosaic' effect)Recommendation: keep paste at ~5–10 % max or the crack pattern changes — always do a test panel. |
Percentages are per 100 parts of component A.
Characteristics
- Consumption (g/m²)
- 150 g/m²official
- Components
- 1official
Colours
- TSE014-05 · neutral (uncoloured tinting base)
Application
HVLP
- Spray viscosity
- as suppliedrecommended
- Consumption
- 150 g/m²official
- Coats
- Catalog: the Craquelure system has two crackle layers (TSE014-05+TSE3 5 %, then TSE014-05+CS70001 5 %), each over its own LEC19812 coat; the Mosaic system has one (TSE014-05 RAL over XGC32). 'One spray pass per layer' is workshop practice, not stated in the catalog.catalog
- Why ru
- Общая практика для кракелюрных составов; Technocolor на этот счёт ничего не указывает.
One even, continuous wet coat — don't go back over it. Film thickness drives crack size: heavier = bigger cracks, lighter = finer. Always spray a test panel on the same build-up.
Conventional spray
- Consumption
- 150 g/m²official
Airmix (air-assisted airless)
- Why ru
- практика мастерской
Airmix for production runs; HVLP is simpler for small batches.
Process and compatibility
- Substrate preparation
- primed panel (PTS20701 isolator + PPS20 primer, or LQA836 + LRR16), then enamel (RAL), then a clear lacquer coat under the crackle: nitro LEC19812 (Craquelure) or water-based XGC32 (Mosaic)catalog
- Goes over
- LEC19812 / XGC32
- System order · Craquelure
- PTS20701, PPS20, RAL enamel, LEC19812, TSE014-05 + TSE3 5 %, LEC19812, TSE014-05 + CS70001 5 %, ATL500
- System order · Mosaic
- LQA836, LRR16, RAL enamel, XGC32, TSE014-05 RAL, LDA401
- Sanding
- Do not sand the crackle layer; denib only the sealed topcoat if needed.recommended
- Topcoat timing
- after the crackle effect has fully developed («после достижения эффекта растрескивания»)catalog
- Temperature and humidity
- 18–25 °C, RH 50–70 %; keep conditions constant between test panel and jobrecommended
- Don'ts
- don't thin without a test panel — it changes the crack pattern
- don't topcoat before cracking has finished
- don't sand the crackle layer
- don't double-pass a wet coat
Storage
Safety: No SDS found. Spray in a ventilated booth with an A2P2 respirator and gloves; keep away from ignition sources.
Used in finishing systems
Sources
Value tags: “official”, “dealer”, “catalog”, “schedule” are Technocolor data; “workshop” is from our own datasheets; “recommended” is our engineering estimate (hover to see the reasoning).
- official page: name, «нейтральный», method spray, 150 g/m²; no hardener/thinner listed (fetched live 2026-10-04, local copy identical)
- dealer search: no result
Not covered by the sources
- product chemistry/binder and carrier (solvent- or water-borne) not published
- solids, viscosity, density, gloss — no official/dealer/TDS data
- drying times (crack development time, overcoat time, full dry) not published
- thinner (if any) not stated
- TSE3 — identity/function and whether 5 % is by weight or volume unknown; no official page or dealer listing
- CS70001 — exact colour not confirmed
- basis (weight vs volume) of the catalog 5 % additions
- not stocked on t-colormarket.ru (search TSE014 / TSE3 returns nothing); not found on woodonline.ru, lakokraska31.ru, ndom31.ru
- no TDS/SDS PDF found (web search budget exhausted in this session; only direct dealer searches tried)
- shelf life, storage temperature, packaging sizes
- the official page text is almost empty — only name and «Распыление 150»