APL70 M
White acrylic enamel (20 gloss), 400 ml aerosol, for restoration work
Restoration-grade acrylic enamel in a spray can: good hiding power, rich colour, fast drying. Fully ready to use — nothing to mix or thin. Sprays a clean pattern with no halo of overspray at the edge. Two actuators in the box: one halo-free tip for spot repairs and gloss matching, one for first-time coating.
- any wood species
- first-time finishing of small surfaces
- refinishing a spot after a defect has been repaired (chips, dents, scratches)
- evening out the sheen over a repaired patch
- touch-up of white and RAL-enamelled doors and furniture
Single-component product: no mixing needed — use as supplied (see application below).
Ask about APL70 M
Answers are based on the APL70 M data and the products it mixes with.
Characteristics
- Gloss
- 20 GU (Глосс)dealer
- Drying · Touch-dry
- 10–20 mindealer
- Drying · Full cure
- 3–4 hdealer
- Drying · Conditions
- 20 °C
- Drying · Dust-free
- 5–10 minrecommended
- Drying · Sand or stack
- 3–4 hrecommended
- Pot life
- not applicablerecommended
Colours
- APL70 M · white
- APL70 R9003 M · signal white
- APL70 R1015 M · light ivory
- APL70 R9001 M · cream white
- APL70 R9010 M · pure white
- APL70 R9016 M · traffic white
Application
Aerosol
- Device
- aerosol_can
- Nozzle
- 2 supplied actuators: halo-free (spot repair, gloss blending) and full-coveragedealer
- Pressure · fluid
- factory can pressurerecommended
- Pressure · air
- not applicablerecommended
- Spray viscosity
- ready to use, do not thindealer
- Gun distance
- 15–25 cmdealer
- Consumption
- 80–100 g/m², 150 g/m²
- Wet film
- 25–40 µm per passrecommended
- Coats
- 2–3 light coatsrecommended
- Flash-off
- 5–10 minrecommended
- Recoat
- wet-on-tacky after 5–10 min, or after 3–4 h with a light scuffrecommended
- Sanding between coats
- if needed P600–P800 or grey Scotch-Brite after full dryrecommended
Shake the can before use. Do not spray onto cold or hot surfaces. Hold 15–25 cm from the surface. When finished, turn the can upside down and spray until clear to purge the nozzle. [derived:] Shake for at least 1–2 min after the ball starts rattling; keep the can parallel to the surface, start spraying before the edge and release past it, overlap passes ~50 %. dealer
Process and compatibility
- Substrate preparation
- Suits any wood species; applied after the defect has been repaired (filler/wax or repair stick, levelled). [derived:] Surface clean, dry and degreased; scuff the repair and surrounding old finish with P400–P600 or Scotch-Brite.dealer
- Goes under
- ATL70 M
- Sanding
- Do not sand or polish the final 20-gloss coat — it changes the sheen.recommended
- Temperature and humidity
- Не наносить на холодные/горячие поверхности; [derived:] работать при 18–25 °C, отн. влажность ≤ 70 %.dealer
- Don'ts
- do not thin or add hardener
- do not spray onto cold or hot surfaces
- do not try to build it in one heavy pass — it will run
- do not store the can without purging the nozzle
Storage
- Packaging
- 400 ml aerosol candealer
- Storage temperature
- +5…+30 °C away from heat and flames; pressurised containerrecommended
Safety: [derived] Pressurised container: do not heat above 50 °C, pierce or burn even when empty. Highly flammable — keep away from flames, use extraction, an A1/A2P2 respirator and gloves. No SDS found.
Sources
Value tags: “official”, “dealer”, “catalog”, “schedule” are Technocolor data; “workshop” is from our own datasheets; “recommended” is our engineering estimate (hover to see the reasoning).
- dealer product page APL70 M: description, properties, use, 80–100 g/m², 15–25 cm, full dry 3–4 h, 20 gloss, 400 ml, white, price 632 RUB; RAL variants 821 RUB
- sibling APL70 SM: touch-dry 10–20 min at 20 °C
- RAL colour variants at 20 gloss (also r1015, r9001, r9010, r9016 pages)
- sibling APL70 UM 10 gloss
- sibling APL70 G 70 gloss
- dealer search listing all APL70 codes
Not covered by the sources
- solids content (not published anywhere; aerosol, ready-to-use)
- viscosity (not published; irrelevant for the user — factory-set in the can)
- density / can fill weight in grams (only 400 ml volume published)
- dust-free and sand/recoat times for APL70 M specifically (touch-dry 10–20 min only published for sibling APL70 SM)
- binder chemistry detail (1K thermoplastic acrylic vs other) — only 'эмаль акриловая' stated
- propellant, can pressure, nozzle orifice sizes of the 2 supplied actuators
- hardness, lightfastness, chemical resistance, elasticity
- shelf life and storage temperature
- safety / hazard statements (no SDS found)
- no Technocolor TDS PDF found (dealer searches on lakokraska31.ru / woodonline.ru / ndom31.ru return nothing for APL70 (re-checked 2026-10-05))
- consumption conflict: catalog 150 g/m² vs dealer 80–100 g/m²
- official t-color.ru page: none