XGC065
XGC065 exterior lacquer/primer, 15 gloss (3-in-1)
Single-pack waterborne 3-in-1 for exterior wood: the same material is the impregnation, the primer and the topcoat. Matt (15 gloss). It tints with XHT pastes, so one tin gives either a clear finish or a translucent colour. High weather resistance and easy to use.
- Wooden houses
- Fences
- Window frames
- Gazebos
- Other exterior wooden structures
Mix calculator
Ratio 100 : 0.0
| Component | Weigh out |
|---|---|
| XGC065part A | 500 g |
| waterThinner | 0.0 g |
| Total | 500 g |
Covers roughly 7.14 m² at 70 g/m².
Ask about XGC065
Answers are based on the XGC065 data and the products it mixes with.
Mixing matrix
- waterThinner% by weight: 0–5 %recommended
Build and top coats — use as supplied; up to 5 % water only if needed (heat, dry air, spraying).
Clean (ideally distilled) water only. Never solvent thinners like S50/S80.
- waterThinner% by weight: 5–10 %recommended
First (impregnating) coat on bare, never-finished wood.
Brush along the grain and work it in; flood the end grain.
- XHT8 / XHT9 / XHT10 / XHT12 / XHT16 / XHT17 / XHT18 / XHT19Additive% by weight: 0–10 (typ. 5) %recommended
Light tint to match the XHT impregnation.
A tinted finish protects the wood from UV much better than an untinted one.
| Role | Material | % by weight | % by volume | When |
|---|---|---|---|---|
| Thinner | water | 0–5 %recommended | — | Build and top coats — use as supplied; up to 5 % water only if needed (heat, dry air, spraying).Clean (ideally distilled) water only. Never solvent thinners like S50/S80. |
| Thinner | water | 5–10 %recommended | — | First (impregnating) coat on bare, never-finished wood.Brush along the grain and work it in; flood the end grain. |
| Additive | XHT8 / XHT9 / XHT10 / XHT12 / XHT16 / XHT17 / XHT18 / XHT19 | 0–10 (typ. 5) %recommended | — | Light tint to match the XHT impregnation.A tinted finish protects the wood from UV much better than an untinted one. |
Percentages are per 100 parts of component A.
Characteristics
- Gloss
- 15 gloss unitsofficial
- Weather resistance
- high weather resistanceofficial
- Components
- 1K (single-component)recommended
- Binder
- waterborne (acrylic/alkyd-acrylic dispersion, exact binder unknown)recommended
- Lightfastness
- depends on XHT pigment load; clear (untinted) film gives little UV protection to the wood itselfrecommended
- Elasticity
- high (must follow seasonal wood movement)recommended
- Thixotropy
- likely mildly thixotropicrecommended
- Min film-forming temp
- below MFFT a waterborne film will not coalesce and cracksofficial
- Drying · Conditions
- 20 °C, 60–65 % RH (assumed)
Colours
- XGC065 · clear (base for XHT tinting)
Application
Brush
- Consumption
- 60–80 g/m² per coatrecommended
- Coats
- 2–3 coatsrecommended
- Recoat
- 4–12 hrecommended
- Sanding between coats
- after coat 1 only: light denib P220–P280 (raised grain); later coats — only if nibsrecommended
Synthetic brush for waterborne coatings. Do not go back over areas that have started to set. Coat end grain twice.
HVLP
- Nozzle
- 1.8–2 mmrecommended
- Pressure · air
- 1.8–2.2 bar at inlet (gun triggered); ≤0.7 bar at the caprecommended
- Spray viscosity
- as supplied (0–5 % water)recommended
- Consumption
- 80–100 g/m² per coatrecommended
- Wet film
- 80–100 µmrecommended
- Coats
- 2–3 coatsrecommended
- Flash-off
- 20–40 min between wet-on-dry passesrecommended
- Recoat
- 4–12 hrecommended
- Sanding between coats
- P220–P280 after the first coat if grain raisedrecommended
Stainless gun/hoses, or flush out all solvent residue first (traces curdle waterborne material). Gun distance 15–20 cm, 50 % overlap.
Conventional spray
- Nozzle
- 1.9–2.5 mmrecommended
- Pressure · air
- 3–4 barrecommended
- Spray viscosity
- as supplied (0–5 % water)recommended
- Consumption
- 80–100 g/m² per coatrecommended
More overspray and waste than HVLP.
Airmix (air-assisted airless)
- Nozzle
- 0.23–0.28 mm (0.009–0.011 in)recommended
- Pressure · fluid
- 80–100 barrecommended
- Pressure · air
- 1–2 barrecommended
- Spray viscosity
- as supplied (0–5 % water)recommended
- Consumption
- 80–100 g/m² per coatrecommended
Pump and hoses must be waterborne-compatible (stainless).
Dipping
Possible as the impregnating coat for small parts (pickets, balusters); drain and brush out runs.
Process and compatibility
- Substrate preparation
- Wood clean and dry (12–15 % MC), free of mould, resin and old film finishes. Sand P120–P150 (P180 for joinery), de-dust. Degrease resinous/oily species (larch, teak, iroko). On infected or unprotected wood apply CPH6 / CTH100 antiseptic first.recommended
- Goes over
- bare wood / CPH6 / CTH100
- Goes under
- XGC065
- End grain
- Seal end grain with HTS30 (Technocolor clear end-grain mastic) or with 2–3 extra coats of XGC065recommended
- Sanding
- Light denib P220–P280 after coat 1 to knock down raised grain. Do not sand the final coat.recommended
- Temperature and humidity
- Air and surface at least +10 °C (ideally 15–25 °C), RH under 80 %. Not in direct sun, not on dew, not before rain; keep it dry for 24 h after application.recommended
- Don'ts
- Do not thin with solvents (S50, S80 etc.) — water only
- Do not mix with 2K materials or add hardeners
- Do not apply below +10 °C, on wet wood or ahead of rain
- Do not apply over oil, wax or old film without stripping it fully
- Do not leave south-facing exterior surfaces untinted — tint with XHT for UV protection
- Do not let the material freeze in the tin
Storage
- Storage temperature
- 5–30 °Crecommended
Safety: Waterborne: low odour, non-flammable. Wear gloves and goggles; when spraying use a particulate respirator (P2). Do not pour leftovers down the drain. Keep away from children.
Sources
Value tags: “official”, “dealer”, “catalog”, “schedule” are Technocolor data; “workshop” is from our own datasheets; “recommended” is our engineering estimate (hover to see the reasoning).
- Official product page: 3-in-1 (impregnation/primer/topcoat), 15 gloss, tinted with XHT pastes, high weather resistance (page contains only 'Свойства')
- Dealer search — no product found (re-checked 2026-10-05)
- Milesi site: XGC-prefixed products (XGCFAA38, XGC6077) are water-based exterior finishes; no XGC065 entry
- Application methods (airmix air 1–2 bar, brush for small areas, dip)
- MFFT definition, hydrophobicity for exterior finishes
- Official sibling page (same 3-in-1 text, 30 gl): spray 80–100, brush 60–80 g/m²
- Official sibling page (same 3-in-1 text, 60 gl): spray 80–100, brush 60–80 g/m²
- Milesi Hydrocrom guide p.6: line-wide spray settings (conventional 1.9–2.5 mm 3–4 bar; airmix 0.23–0.28 mm 80–100 bar, air 1–2 bar; airless 120–150 bar)
- Milesi guide p.11: XGC 63 'Finitura tixotropica … estremamente elastica'; XGC 65 not listed
Not covered by the sources
- No dealer listing: t-colormarket.ru search for XGC065 returns no product (checked 2026-10-04); lakokraska31.ru, woodonline.ru, ndom31.ru also no hit
- No TDS/SDS found (Milesi site search for 'XGC 065' empty; web search budget exhausted)
- Not printed in the 2025–2026 catalogue or the exterior leaflet
- Solids %, viscosity, density — unknown
- Binder chemistry not stated officially (waterborne derived from XGC = Milesi waterborne prefix)
- Drying times (dust-free/touch/recoat/full) — not published (derived)
- XHT paste dose limits and colour cards — not published
- Shelf life, packaging sizes — unknown
- No official finishing schedule (information/technology) uses XGC065
- Hardness, chemical resistance, lightfastness ratings — not published
- Consumption not published for XGC065 itself — 80–100 (spray) / 60–80 (brush) g/m² taken from sibling XGC063/XGC06D official pages
- Thinning ratio and number of coats — not published (derived)
- Identity XGC065 = 15-gloss member of Milesi XGC 6x Hydrocrom line is inferred; Milesi guide lists XGC 63 but not XGC 65