OTL60
OTL60 Terrace (decking) oil — clear and tinted OTL60.10–OTL60.20
Oil for exterior wood. Penetrates deep into the wood structure, protecting it from the weather; resists mould and fungus.
- decks and terraces
- verandas and gazebos
- garden furniture
- cladding and facade panels
- fences
- exterior steps
- landscaping timber
- pine and larch
Mix calculator
Ratio 100 : 0.0
| Component | Weigh out |
|---|---|
| OTL60part A | 500 g |
| S60Thinner | 0.0 g |
| Total | 500 g |
Covers roughly 6.58 m² at 76 g/m².
Pot life of the mix: n/a — one-component oil, no hardener.
Ask about OTL60
Answers are based on the OTL60 data and the products it mixes with.
Mixing matrix
- CLAdditive% by weight: 5 %dealer
To tint clear OTL60 to a custom shade.
CL tinting is stated on the dealer page for clear OTL60 ('tinted with CL-series pastes') and in the exterior-materials leaflet (for PTL33). The 5 % ceiling comes from OTL10 in the same oil line. More paste = poorer penetration and slower dry; always do a test panel.
- S60Thinner% by weight: 0–5 %recommended% by volume: 0–6 %recommended
Normally used neat. Up to 5 % S60 for dense/resinous larch or cool conditions.
S60 is officially listed for cleaning brushes.
| Role | Material | % by weight | % by volume | When |
|---|---|---|---|---|
| Additive | CL | 5 %dealer | — | To tint clear OTL60 to a custom shade.CL tinting is stated on the dealer page for clear OTL60 ('tinted with CL-series pastes') and in the exterior-materials leaflet (for PTL33). The 5 % ceiling comes from OTL10 in the same oil line. More paste = poorer penetration and slower dry; always do a test panel. |
| Thinner | S60 | 0–5 %recommended | 0–6 %recommended | Normally used neat. Up to 5 % S60 for dense/resinous larch or cool conditions.S60 is officially listed for cleaning brushes. |
Percentages are per 100 parts of component A.
Characteristics
- Solids
- 42 ± 1 %official
- Viscosity
- 12 ± 2 sofficial
- Density
- 0.91 ± 0.01 g/cm³ (удельный вес)official
- Gloss
- none (matt, non-film)dealer
- Pot life
- n/a — one-component oil, no hardenerrecommended
- Drying · Recoat (h)
- ≥ 12 hdealer
- Drying · Sand or stack
- ≥ 12 hofficial
- Drying · Full cure
- 24 hdealer
- Drying · Wipe off (min)
- 10–15 mindealer
- Drying · Conditions
- 20 °C
- Lightfastness
- tinted variants contain a UV filterdealer
- Chemical resistance
- improved physical/chemical resistance; water- and dirt-repellentcatalog
- Biocidal
- resists mould and fungusofficial
- Service life
- up to 10 years (dealer); separately, a yearly refresh coat is recommended as neededdealer
- Thixotropy
- norecommended
Colours
- OTL60 · clear
- OTL60.10 · white
- OTL60.11 · alder
- OTL60.12 · pine
- OTL60.13 · walnut
- OTL60.14 · cherry
- OTL60.15 · rosewood
- OTL60.16 · olive
- OTL60.17 · wenge
- OTL60.18 · tobacco
- OTL60.19 · grey
- OTL60.20 · graphite
Application
Brush
- Coverage (m²/L)
- 10–15 m²/Ldealer
- Consumption
- 61–91 g/m²recommended
- Coats
- 2dealer
- Flash-off
- 10–15 mindealer
- Recoat
- ≥ 12 hdealer
- Sanding between coats
- not requiredrecommended
- Tool
- natural-bristle brush with stiff bristles, work the oil indealer
Apply evenly and work it in along the grain; after 10–15 min wipe off the excess with a rag — oil left standing on top stays tacky and darkens.
Roller
- Coverage (m²/L)
- 10–15 m²/Ldealer
- Coats
- 2dealer
- Recoat
- ≥ 12 hdealer
- Flash-off
- 10–15 mindealer
- Why ru
- Валик оставляет лужицы в канавках; растушёвка кистью следом — стандартная практика для террасных масел и соответствует официальному указанию «втирать».
On decking: lay it on with a roller, then back-brush along the board including ends and grooves; wipe off excess.
Cloth or pad
- Coverage (m²/L)
- 10–15 m²/Ldealer
- Coats
- 2dealer
Rag application is listed by the dealer for OTL60 (brush, rag, roller). Handy for garden furniture and maintenance coats.
HVLP
- Nozzle
- 1–1.3 mmrecommended
- Pressure · air
- 1.5–2 barrecommended
- Spray viscosity
- as supplied, 12 ± 2 s DIN4recommended
- Consumption
- 61–91 g/m²recommended
- Flash-off
- 10–15 mindealer
NOT an official method. Use only to flood the surface fast, then always back-brush/wipe off. Use a water-wash booth or change filters often — oil overspray in filters can self-ignite.
Airmix (air-assisted airless)
- Nozzle
- 0.18–0.23 mmrecommended
- Pressure · fluid
- 10–20 barrecommended
- Pressure · air
- 1–2 barofficial
NOT official; for production runs of cladding boards. Always wipe/brush in after spraying.
Process and compatibility
- Substrate preparation
- Degrease, sand P100–P120, remove dust.dealer
- Wood species
- suitable for pine and larchdealer
- Maintenance
- Refresh once a year as needed with one coat of tinted oil, no sanding.dealer
- Sanding
- Prep only, P100–P120; no sanding between coats or for maintenance.dealer
- Temperature and humidity
- 10–35 °Cdealer
- Don'ts
- Do not use indoors (tinted OTL60.10–.20).
- Do not leave excess oil on the surface — wipe it off after 10–15 min.
- Never leave oily rags, clothing or sanding dust lying around — spontaneous-combustion risk: put them in a metal can under water.
- Do not pour down the drain.
Storage
- Storage temperature
- cool, dry, out of direct sun, can tightly closeddealer
Safety: Wear gloves and ventilate; keep away from flames and sparks; avoid skin and eye contact, rinse with water if it happens. Oil-soaked materials can self-ignite. Keep away from children; do not swallow.
Sources
Value tags: “official”, “dealer”, “catalog”, “schedule” are Technocolor data; “workshop” is from our own datasheets; “recommended” is our engineering estimate (hover to see the reasoning).
- official page clear OTL60: properties, application, density, drying ≥12 h, solids 42±1 %, viscosity 12±2 s DIN4, appearance
- 11 official colour pages OTL60.10–.20, identical data
- dealer clear OTL60: brush/rag/roller, 10–15 m²/L, CL tinting, gloss 'нет', 1 L and 5 L packs
- dealer tinted (identical across .10–.20): method, 2 coats, 12 h between, 24 h full, wipe 10–15 min, S60 cleaning, P100–120, 10–35 °C, yearly refresh, pine/larch, safety
- sibling OTL10: S60 ≤5 % and CL ≤5 % limits used as derived/analogue
- methods page (airmix air 1–2 bar; brush description)
Not covered by the sources
- Dust-free and touch-dry times not published (only ≥12 h recoat, 24 h full dry)
- Shelf life not published
- Exact dilution limit for OTL60 not published (S60 ≤5 % taken from sibling OTL10, marked derived)
- CL-paste max % for OTL60 not published (5 % from OTL10)
- Exact CL paste codes compatible with OTL60 not listed (unclear if CL = CLT Кромолюкс series)
- Leaflet «Материалы для наружных работ» lists terrace oil under code PTL33 'Прозрачное' — relation to OTL60 (old code?) unconfirmed
- Foot-traffic / service readiness time and RH limits not published
- Spray application not covered by any Technocolor source — all spray settings are derived
- No official finishing schedule (information/technology) uses OTL60
- No Technocolor TDS/SDS PDF found for OTL60 (dealer shows no PDF)
- S60 density not published — thinner % by volume is an estimate
- Official t-color.ru OTL60 pages do not mention oils/waxes, UV filter, film or service life — those come from dealer/leaflet only