HTL20030
HTL20030 Water-based lacquer/primer (30 gloss)
One-pack water-based lacquer/primer, 30 gloss: the same material is used for the sealer coat and the topcoat. Fast drying, does not run, good looks and physical/chemical performance, excellent non-yellowing. The officially stated application is spraying at 100–120 g/m²; the official page URL ('dlya-okunaniya', i.e. 'for dipping') also points to dipping. No organic solvents - cures by water evaporation.
- Chairs (dipping the assembled frame)
- Turned parts in any species: spindles, legs, handles
- Slatted furniture and cots (dip method per the official methods page)
- Kids' furniture and toys where a solvent-free finish is wanted
Mix calculator
Ratio 100 : 5.0
| Component | Weigh out |
|---|---|
| HTL20030part A | 476 g |
| WATERThinner | 23.8 g |
| Total | 500 g |
Covers roughly 5.00 m² at 100 g/m².
Ask about HTL20030
Answers are based on the HTL20030 data and the products it mixes with.
Mixing matrix
- WATERThinner% by weight: 0–10 %official% by volume: 0–10 %official
Only to adjust dip-tank or spray viscosity.
Use demineralised water only - no hard, salty tap water.
- WATERThinner% by weight: 0–5 %dealer
The dealer caps thinning at 5 % - for dipping, stay within that.
Conflict: official page 0–10 % by weight and by volume; dealer 'do not exceed 5 % thinning' (basis - weight or volume - not stated).
| Role | Material | % by weight | % by volume | When |
|---|---|---|---|---|
| Thinner | WATER | 0–10 %official | 0–10 %official | Only to adjust dip-tank or spray viscosity.Use demineralised water only - no hard, salty tap water. |
| Thinner | WATER | 0–5 %dealer | — | The dealer caps thinning at 5 % - for dipping, stay within that.Conflict: official page 0–10 % by weight and by volume; dealer 'do not exceed 5 % thinning' (basis - weight or volume - not stated). |
Percentages are per 100 parts of component A.
Characteristics
- Gloss
- 30 GUofficial
- Components
- 1K, no hardenerofficial
- Drying · Sand after (h)
- 4 hdealer
- Drying · Full cure
- 8 hdealer
- Drying · Conditions
- assumed 20 °C (not stated on the dealer page); apply above 15 °C, RH < 70 %
- Sag resistance
- does not rundealer
- Yellowing
- excellent non-yellowingofficial
- Solvent content
- no organic solventscatalog
Application
Dipping
- Consumption
- 100 per coat (sealer and topcoat) g/m²dealer
- Coats
- 2dealer
- Dip viscosity
- 20–35 s DIN4 / VZ-4recommended
- Immersion and withdrawal
- immerse 10–30 s, withdraw slowly and evenly (≈10–30 cm/min); hang to drain 10–20 min, wick off the drip pointrecommended
- Flash-off
- 10–20 minrecommended
- Recoat
- after 4 h + sandingdealer
- Sanding between coats
- P240–P280 after 4 hdealer
Keep the tank covered, stir before work, filter the bath. Never let it freeze. Dedust before dipping. Watch the drip at the lowest point - touch it off on the tank lip or with a brush.
HVLP
- Consumption
- 100–120 g/m²official
- Coats
- 2dealer
- Nozzle
- 1.3–1.5 (typ. 1.4) mmrecommended
- Pressure · air
- 2–2.2 barrecommended
- Spray viscosity
- 25–45 s DIN4 / VZ-4recommended
- Gun setup · Gun distance
- 15–20 cmrecommended
- Gun setup · Overlap
- 50–75 %recommended
- Gun setup · Air demand
- 10–13 CFMrecommended
- Wet film
- 95–117 µmrecommended
- Recoat
- after 4 h + sanding P240–P280dealer
- Sanding between coats
- P240–P280dealer
Thin even coats; a heavy wet WB coat dries slowly and can mill white. Flush gun and lines with water before and after.
Airmix (air-assisted airless)
- Consumption
- 100–120 g/m²official
- Nozzle
- 0.23–0.28 mmrecommended
- Pressure · fluid
- 40–70 barrecommended
- Pressure · air
- 1–2 barofficial
Electrostatic airmix is a good fit for chairs and slatted work - much less overspray (see the methods page).
Process and compatibility
- Substrate preparation
- Sanded wood (P150–P180 on solid), dust-free; no oil or silicone contamination.recommended
- Goes under
- HTL20030
- Sanding
- P240–P280 between coatsdealer
- Temperature and humidity
- above 15 °C, RH below 70 %dealer
- Don'ts
- Don't apply below 15 °C or above 70 % RH
- Don't thin with hard tap water - demineralised only
- Don't thin past 5 % (dealer; official page allows up to 10 %)
- Don't mix with solvents or solvent-borne products
- Don't let it freeze
Storage
- Storage temperature
- 5–30 °Crecommended
- Packaging
- 1 kg,5 kg,10 kgdealer
- Before use
- stir thoroughlyrecommended
Safety: Water-borne, no organic solvents: low odour, low fire risk. Still wear a mist respirator when spraying and gloves; clean up with water.
Sources
Value tags: “official”, “dealer”, “catalog”, “schedule” are Technocolor data; “workshop” is from our own datasheets; “recommended” is our engineering estimate (hover to see the reasoning).
- official page: title 'HTL20030 Лак/грунт ВР (30 Глосс)', properties, spray 100–120 g/m², water 0–10 % w/w and v/v (no dip method, no hardener)
- dealer page (archived 2025-05-20): uses, notes (>15 °C, RH<70 %, demineralised water, ≤5 %), instruction schedule 100 g/m²/4 h/P240–P280/100 g/m²/8 h, packaging
- live dealer URL - now 404
- official methods page: dip, airmix, electrostatic
- sibling HTL20 SM dealer page - context only
Not covered by the sources
- solids_pct (part A) - not published for HTL20030 (dealer 'Все технические характеристики' block is empty; page now delisted)
- viscosity as supplied / dip-bath viscosity
- density
- gloss tolerance
- dust-free / touch-dry time
- hardness, chemical resistance, elasticity, lightfastness figures
- shelf life
- storage temperature (only derived)
- dip consumption per m² specific to dipping (dealer 100 g/m² figure is method-less)
- no technical data sheet (ТДС) PDF found
- not in the 2025–2026 catalog or any official finishing schedule
- compatibility over solvent-borne stains/primers