HPS10
HPS10 White water-based primer
White water-based (ВР) primer. High hiding power, sag-resistant (thixotropic), sands very well, contains no solvents. Cures purely by water evaporation (water-based section intro).
- children's cots, chairs and other furniture
- toys (2022 catalog and dealer)
- items with strict environmental requirements
Mix calculator
Ratio 100 : 5.0
| Component | Weigh out |
|---|---|
| HPS10part A | 476 g |
| waterThinner | 23.8 g |
| Total | 500 g |
Covers roughly 4.55 m² at 110 g/m².
Pot life of the mix: not applicable – one-pack, no hardener.
Ask about HPS10
Answers are based on the HPS10 data and the products it mixes with.
Mixing matrix
- waterThinner% by weight: 0–10 %official% by volume: 0–15 %official
Thin with clean (ideally demineralised or drinking-quality) water only as needed for the gun; on vertical work keep the water to a minimum to keep the anti-sag body.
No solvent thinners (S50/S80 etc.) – water only. No hardener is used.
| Role | Material | % by weight | % by volume | When |
|---|---|---|---|---|
| Thinner | water | 0–10 %official | 0–15 %official | Thin with clean (ideally demineralised or drinking-quality) water only as needed for the gun; on vertical work keep the water to a minimum to keep the anti-sag body.No solvent thinners (S50/S80 etc.) – water only. No hardener is used. |
Percentages are per 100 parts of component A.
Characteristics
- Solids
- 55 % by weight, part Acatalog
- Viscosity
- 90 ± 5 sdealer
- Thixotropy
- yescatalog
- Pot life
- not applicable – one-pack, no hardenerrecommended
- Drying · Touch-dry
- 15 mindealer
- Drying · Full cure
- 8 hdealer
- Drying · Sand or stack
- 2–3 hrecommended
- Drying · Conditions
- 20 °C
- Drying · Speed
- dries fastofficial
Colours
- HPS10 · white
Application
HVLP
- Nozzle
- 1.8–2.2 (typ. 2) mmrecommended
- Pressure · air
- 2–2.5 barrecommended
- Spray viscosity
- 40–60 s VZ-4 / DIN4 (after stirring)recommended
- Consumption
- 100–120 g/m²official
- Wet film
- 80–110 µmrecommended
- Coats
- 1–2recommended
- Flash-off
- 20–30 minrecommended
- Recoat
- next primer coat after 20–30 min; topcoat after sanding (≥ 2–3 h, better overnight)recommended
- Sanding between coats
- P240–P320 (P320–P400 under gloss enamel)recommended
- Gun setup
- 15–20 cm, 50 % overlap, full fanrecommended
Officially only spraying (air spray) is listed. Use a gun with stainless fluid passages; flush with water before and after (dealer note).
Conventional spray
- Nozzle
- 1.8–2 mmrecommended
- Pressure · air
- 3–4 barrecommended
- Pressure · fluid
- 0.8–1.5 barrecommended
- Consumption
- 110–140 g/m²catalog
Air spray is the method icon shown in the catalog.
Airmix (air-assisted airless)
- Nozzle
- 0.28–0.33 mmrecommended
- Pressure · fluid
- 20–60 barrecommended
- Pressure · air
- 1–2 barofficial
Good for production chairs and cots – high transfer, the thixotropy holds the film.
Airless
- Nozzle
- 0.28–0.38 mmrecommended
- Pressure · fluid
- 100–150 barrecommended
Electrostatic
- Why ru
- Страница методов называет электростатику подходящей для стульев и детских кроваток (целевое применение этого продукта), но для токопроводящих водных материалов нужны изолированные системы.
Only with electrostatic equipment rated for water-borne coatings (isolated feed) – water-borne paint is conductive.
Process and compatibility
- Substrate preparation
- P180–P220 on wood, P180–P240 on MDF, dust-free, 8–12 % moisturerecommended
- Goes over
- bare wood / MDF/HDF / veneer
- Goes under
- HPL20 SM
- Sanding
- P240–P320 before topcoatrecommended
- Temperature and humidity
- > 18 °C, RH < 70 %dealer
- Don'ts
- don't thin with solvents – water only, max 10 % by weight
- don't apply below 18 °C or above 70 % RH
- don't let it freeze
- don't sand before it's dry – it clogs the paper
Storage
- Packaging
- 1, 5, 10 kgdealer
- Storage temperature
- 5–30 °Crecommended
Safety: No organic solvents, low odour, non-flammable; suitable for children's furniture and toys. Still wear a particulate mask when spraying.
Sources
Value tags: “official”, “dealer”, “catalog”, “schedule” are Technocolor data; “workshop” is from our own datasheets; “recommended” is our engineering estimate (hover to see the reasoning).
- official page: properties, method, water thinner % by weight/volume, 100–120 g/m²
- dealer: viscosity 90 ± 5 s VZ-4, touch 15 min, full 8 h, 150 g/m², >18 °C / RH <70 %, packaging
- 2022 web catalog: 'Грунт ВР белый тиксотропный', 55 % solids, water 0–10 %, 110–140 g/m²
- application methods (airmix/airless pressures, electrostatic for chairs/cots)
Not covered by the sources
- density (not published)
- hardness, elasticity value, lightfastness, chemical resistance – not published
- shelf life – not published
- no official finishing schedule uses HPS10
- no ТДС PDF found online
- consumption figures disagree between official page (100–120), catalogs (110–140) and dealer (150 g/m²)
- dust-free and sanding/stacking times not published (only touch 15 min and full dry 8 h, dealer)
- solids % is catalog-only (official page just says 'high'); dealer lists no solids