HPL20 SM
HPL20 SM universal white waterborne enamel (30 gloss)
One-pack white waterborne enamel, 30 gloss. Fast drying, good looks and chemical/physical resistance, high resistance to yellowing. No organic solvents, so it is fine for children's furniture and toys, and stands up to frequent washing.
- solid wood, MDF, veneer (over primer)
- children's furniture and toys
- interior furniture, doors and walls
- decorative hand-painting
Mix calculator
Ratio 100 : 5.0
| Component | Weigh out |
|---|---|
| HPL20 SMpart A | 476 g |
| WATERThinner | 23.8 g |
| Total | 500 g |
Covers roughly 4.55 m² at 110 g/m².
Pot life of the mix: not applicable.
Ask about HPL20 SM
Answers are based on the HPL20 SM data and the products it mixes with.
Mixing matrix
- WATERThinner% by weight: 0–10 %official% by volume: 0–10 %official
Only to trim spray viscosity; usually 5–10 %.
Catalog confirms water 0–10 %. No hardener — single-pack. Use clean (ideally demineralised) water, never solvents.
| Role | Material | % by weight | % by volume | When |
|---|---|---|---|---|
| Thinner | WATER | 0–10 %official | 0–10 %official | Only to trim spray viscosity; usually 5–10 %.Catalog confirms water 0–10 %. No hardener — single-pack. Use clean (ideally demineralised) water, never solvents. |
Percentages are per 100 parts of component A.
Characteristics
- Solids
- 41 % by weight, part Adealer
- Viscosity
- 45 ± 5 sdealer
- Density
- 1.25–1.35 g/cm³recommended
- Gloss
- 30 GUdealer
- Pot life
- not applicablerecommended
- Drying · Touch-dry
- 30 mindealer
- Drying · Full cure
- 8 hdealer
- Drying · Dust-free
- 15–20 minrecommended
- Drying · Sand or stack
- 3–4 hrecommended
- Drying · Conditions
- 20 °C (dealer); apply above 15 °C and below 70 % RH
- Hardness
- withstands frequent washingofficial
- Lightfastness
- high resistance to yellowingsource
- Chemical resistance
- good physico-chemical properties; withstands frequent washingofficial
- Thixotropy
- norecommended
Colours
- HPL20 SM · white
Application
HVLP
- Consumption
- 100–120 g/m²official
- Spray viscosity
- 25–35 s DIN4/ВЗ-4recommended
- Nozzle
- 1.6–1.8 (typ. 1.7) mmrecommended
- Pressure · fluid
- gravity cup; pressure pot 0.8–1.2 barrecommended
- Pressure · air · Inlet pressure
- 2–2.5 bar (trigger pulled)
- Pressure · air · Cap
- 0.7 bar
- Pressure · air · Why ru
- Соответствие HVLP; то же окно, что владелец использует для ATL50, верхняя граница — для более тяжёлой пигментированной водной смеси.
- Wet film
- 75–95 µmrecommended
- Coats
- 2 over a white waterborne primerrecommended
- Flash-off
- 10–20 minrecommended
- Recoat
- wet-on-dry after 1–2 h without sanding, or after 3–4 h+ with a denibrecommended
- Sanding between coats
- P320–P400 or grey pad, light denib only; do not sand the final coatrecommended
- Gun distance
- 15–20 cmrecommended
HVLP, 1.6–1.8 mm stainless tip (1.7 typical), 2.0–2.5 bar inlet with trigger pulled, ≤0.7 bar at the cap, fan open, 15–20 cm, 50–75 % overlap. Flush the gun with water before and after (dealer). Never let solvent-lacquer residue get into the cup. source
Conventional spray
- Consumption
- 100–120 g/m²catalog
- Nozzle
- 1.4–1.6 mmrecommended
- Pressure · air
- 3–4 barrecommended
Air spray is an official method (catalog icon). Transfer efficiency up to ~40 % (methods page).
Airmix (air-assisted airless)
- Nozzle
- 09–11 thou (0.23–0.28 mm), 40–50° fanrecommended
- Pressure · fluid
- 40–80 barrecommended
- Pressure · air
- 1–2 barrecommended
For production runs on fronts and doors. Not listed for HPL20 (only air spray and brush are) — test on a sample first.
Airless
- Nozzle
- 11–13 thou (0.28–0.33 mm)recommended
- Pressure · fluid
- 100–150 barrecommended
Large flat panels only; airmix gives a better finish. Not officially listed for HPL20.
Brush
- Consumption
- 100–120 g/m²catalog
- Coats
- 2–3 thin coatsrecommended
- Why ru
- Натуральная щетина набухает в воде; для водных эмалей стандарт — синтетика.
Synthetic-bristle brush (for waterborne), thin 5–10 % with water. Good for small parts, touch-ups and decorative painting.
Process and compatibility
- Substrate preparation
- Solid wood, MDF, veneer — clean, dry, dust-free; sand P180–P240, then a white waterborne primer.recommended
- Sanding · Primer
- P240–P320
- Sanding · Between coats
- P320–P400 / grey pad
- Sanding · Final
- do not sand
- Sanding · Why ru
- Стандарт для пигментированных водных систем.
- Temperature and humidity
- above 15 °C, RH below 70 %dealer
- Don'ts
- don't tint it — use converter HPL1 for colours
- don't apply below 15 °C or above 70 % RH
- don't thin with solvent or mix with solvent-borne products
- don't exceed 10 % water
- don't let it freeze
- no steel wool/bare steel tools — rust spots in a waterborne film
Storage
- Packaging
- 1 kg,5 kg,10 kgdealer
- Storage temperature
- +5…+30 °C, protect from frostrecommended
Safety: No organic solvents, low odour; suitable for children's furniture and toys. Clean equipment with water. Wear gloves; use a particulate respirator when spraying.
Sources
Value tags: “official”, “dealer”, “catalog”, “schedule” are Technocolor data; “workshop” is from our own datasheets; “recommended” is our engineering estimate (hover to see the reasoning).
- official page: fast drying, good aesthetic and physico-chemical properties; spray 100–120 g/m²; water 0–10 % by weight and by volume
- dealer: gloss 30±3, solids 41±1 %, viscosity 45±5 s ВЗ-4 at 20 °C, touch 30 min, full 8 h at 20 °C, >15 °C/<70 % RH, spray 150 g/m², water flush, packs 1/5/10 kg, 913 ₽/kg; substrates solid wood/MDF/veneer; non-yellowing; children's furniture and toys
- official news 'Серия HPL' (26.02.2026): HPL20 white, interior, NOT tintable; furniture/toys/doors/walls; washable; fast drying; art painting; HPL1 is the tintable converter
- methods page: spray method pressures/transfer efficiency
Not covered by the sources
- shelf life (not published anywhere found)
- density (only derived estimate)
- dust-free and sand/stack times (only touch 30 min and full 8 h published)
- hardness, elasticity, abrasion values
- no Technocolor TDS PDF found for HPL20
- no official finishing schedule uses HPL20
- official primer pairing (HPS10/20/50 is derived)
- consumption conflict: official/catalog 100–120 g/m² vs dealer 150 g/m²
- pot life n/a (1K); no spray viscosity published
- dealer/official give no application method other than spray; brush only from catalog icon