CPH625
CPH625 Mahogany wood stain/lasure (waterborne, exterior)
Waterborne mahogany lasure with wax for exterior wood. Pigmented, colours evenly without blotching, levels well and is lightfast — protects the wood against UV and does not fade. Because it contains wax it is a finish coat in its own right; no lacquer goes on top. Contains no biocides, so it can also be used indoors; outdoors the wood should first be treated with CTH100 preservative.
- Gazebos, fences, railings, garden structures
- Window frames, cladding and log/timber house exteriors
- Interior timber (biocide-free)
Mix calculator
Ratio 100 : 0.0
| Component | Weigh out |
|---|---|
| CPH625part A | 500 g |
| waterThinner | 0.0 g |
| Total | 500 g |
Covers roughly 7.14 m² at 70 g/m².
Ask about CPH625
Answers are based on the CPH625 data and the products it mixes with.
Mixing matrix
- waterThinner% by weight: 0–5 %recommended% by volume: 0–5 %recommended
Only if it has thickened, in hot weather, or for spraying
No solvent thinners (S50/S80 etc.) — this is a waterborne product.
| Role | Material | % by weight | % by volume | When |
|---|---|---|---|---|
| Thinner | water | 0–5 %recommended | 0–5 %recommended | Only if it has thickened, in hot weather, or for sprayingNo solvent thinners (S50/S80 etc.) — this is a waterborne product. |
Percentages are per 100 parts of component A.
Characteristics
- Gloss
- матовый (matt)dealer
- Drying · Full cure
- 4 hdealer
- Drying · Conditions
- 20 °C
- Lightfastness
- high, non-fading, UV-protectiveofficial
- Levelling
- good levellingofficial
- Water repellency
- water-repellent film (per CPH600 series binder)recommended
- Biocides
- nonecatalog
- Components
- 1K, ready to userecommended
Colours
- CPH625 · Mahogany
Application
Brush
- Consumption
- 60–80 g/m²official
- Coats
- 1–2 coatsdealer
- Recoat
- when fully dry, ~4 h at 20 °Crecommended
- Sanding between coats
- optional; if grain raises, light pass with P180–P240 along the grainrecommended
Brush along the grain, no puddles; lay off the excess and keep a wet edge to avoid lap marks. Stir before and during use — pigment settles.
HVLP
- Nozzle
- 1.2–1.4 mmrecommended
- Pressure · air
- 1.5–2 barrecommended
- Pressure · fluid
- 0.5–1 barrecommended
- Spray viscosity
- as supplied, ≤5 % water if neededrecommended
- Consumption
- 60–80 g/m²recommended
- Coats
- 1–2 coatsdealer
Spray light, then back-brush along the grain straight away so it penetrates evenly without striping. For exterior work brushing is preferred — it drives the lasure into pores and end grain better.
Process and compatibility
- Substrate preparation
- Dry (wood moisture 8–14 %), clean, grease-free wood with old film finishes removed; sand P120–P150 (no finer than P180 — finer closes the pores and blocks penetration). Outdoors, treat first with CTH100 preservative and let it dry.recommended
- Goes over
- CTH100 / CPH6
- Temperature and humidity
- Apply at +10…+30 °C, RH 40–75 %; not in direct sun, on wet wood, before rain or if night frost is expected.recommended
- Don'ts
- Do not lacquer over it — the wax lasure is the finish
- Do not thin with solvents
- Do not let it freeze
- Do not flood it on thick — blotches and tackiness
Storage
- Packaging
- 1 кг,5 кгdealer
- Storage temperature
- keep from freezingrecommended
Safety: Waterborne and biocide-free — allowed indoors. Wear gloves; use a particle/mist respirator when spraying. Do not pour waste down the drain.
Mixed into
Sources
Value tags: “official”, “dealer”, “catalog”, “schedule” are Technocolor data; “workshop” is from our own datasheets; “recommended” is our engineering estimate (hover to see the reasoning).
- official page: properties, wax, finish without lacquer, brush 60–80 g/m²
- dealer: description, CTH100 pre-treatment, 1–2 coats, matt, full dry 4 h @20 °C, packs 1/5 kg, price
- CPH600 colourless binder of the series: hydrophobic coating
- wood moisture 8–14 %, RH 40–75 %
- application methods (brush; HVLP general)
Not covered by the sources
- solids_pct (not published by official site, dealer or catalogs)
- viscosity
- density
- dust-free / touch-dry time (only full dry 4 h given)
- recoat interval (official)
- official thinning ratio (water %)
- shelf life
- official storage temperature
- official spray/dip parameters (only brush listed for CPH lasures)
- no Technocolor TDS PDF found for CPH625
- not used in any official finishing schedule (information/technology)