XGC072
XGC072 exterior wood lacquer, 30 gloss (satin)
Exterior lacquer, 30 gloss. High weather resistance, excellent flow-out and sag resistance.
- Topcoat for exterior joinery: windows, doors, cladding, gazebos, fences
- Clear topcoat over exterior impregnations/stains
Mix calculator
Ratio 100 : 0.0
| Component | Weigh out |
|---|---|
| XGC072part A | 500 g |
| Water (demineralised)Thinner | 0.0 g |
| Total | 500 g |
Covers roughly 2.22 m² at 225 g/m².
Pot life of the mix: n/a (1K).
Ask about XGC072
Answers are based on the XGC072 data and the products it mixes with.
Mixing matrix
- Water (demineralised)Thinner% by weight: 0–5 %recommended% by volume: 0–5 %recommended
Only if the label confirms it is waterborne and it won't atomise cleanly (heat, small tip).
No source gives a thinner. If the label says solvent-borne, do NOT add water — ask Technocolor.
| Role | Material | % by weight | % by volume | When |
|---|---|---|---|---|
| Thinner | Water (demineralised) | 0–5 %recommended | 0–5 %recommended | Only if the label confirms it is waterborne and it won't atomise cleanly (heat, small tip).No source gives a thinner. If the label says solvent-borne, do NOT add water — ask Technocolor. |
Percentages are per 100 parts of component A.
Characteristics
- Gloss
- 30 GUofficial
- Thixotropy
- high sag resistance ('стойкость к подтекам')official
- Flow
- excellent flow-out ('отличная растекаемость')official
- Weather resistance
- high ('высокая атмосферостойкость')official
- Pot life
- n/a (1K)recommended
- Density
- ≈1.03–1.05 g/cm³recommended
Colours
- XGC072 · clear
Application
HVLP
- Nozzle
- 1.7–2 mmrecommended
- Pressure · fluid
- gravity cup, or 1.0–1.5 bar on a pressure potrecommended
- Pressure · air
- 2–2.5 barrecommended
- Spray viscosity
- as suppliedrecommended
- Consumption
- 150–300 g/m²official
- Wet film
- 145–290 µmrecommended
- Coats
- 2–3recommended
- Flash-off
- 15–30 minrecommended
- Recoat
- next day (or when sandable without clogging)recommended
- Sanding between coats
- light denib P240–P320recommended
- Gun distance
- 15–20 cmrecommended
- Overlap
- 50–75 %recommended
Lay a full wet coat, don't dust it on. Stir well first. Stainless kit, flush with water (if waterborne is confirmed).
Conventional spray
- Nozzle
- 1.6–1.9 mmrecommended
- Pressure · air
- 3–4 barrecommended
- Consumption
- 150–300 g/m²official
Airmix (air-assisted airless)
- Nozzle
- 0.28–0.33 mmrecommended
- Pressure · fluid
- 30–80 barrecommended
- Pressure · air
- 1–2 barofficial
- Consumption
- 150–300 g/m²official
Waterborne-rated (stainless) pump and hoses if waterborne.
Airless
- Nozzle
- 0.33–0.38 mmrecommended
- Pressure · fluid
- 120–180 barrecommended
- Consumption
- 150–300 g/m²official
Brush
- Consumption
- 150–300 g/m²official
- Coats
- 2–3recommended
Synthetic brush, along the grain, don't overwork; the good flow levels the brush marks.
Process and compatibility
- Substrate preparation
- Dry (12–15 % MC), sanded, dust-free wood; outdoors start with a preservative impregnation (CTH100/CPH6) or a CPH stain.recommended
- Goes over
- CTH100 / CPH6 / CPH60–CPH66 / CPH600–CPH626
- Sanding · Between coats
- P240–P320 denibrecommended
- Sanding · Final
- do not sand the final coatrecommended
- Temperature and humidity
- +15…+30 °C, RH < 70 %, no rain/dew for 24 h, not in direct sunrecommended
- Don'ts
- Don't apply below 15 °C, on dew, in rain or full sun.
- Don't thin with S50/S80 solvents (compatibility not confirmed).
- Don't apply over wet wood.
- Don't let the can freeze.
Storage
- Storage temperature
- 5–30 °Crecommended
Safety: When spraying wear a mask (P2 for waterborne, A2P2 if it turns out solvent-borne) and ventilate.
Sources
Value tags: “official”, “dealer”, “catalog”, “schedule” are Technocolor data; “workshop” is from our own datasheets; “recommended” is our engineering estimate (hover to see the reasoning).
- official page: properties (weather resistance, flow, sag resistance), spray/brush 150–300 g/m², 30 gloss
- sister XGC063/065/06D pages: tinted with XHT pastes (context for series)
- application methods page (airmix 1–2 bar air, airless up to 200 bar)
- dealer search — no result
Not covered by the sources
- chemistry not confirmed by any source (waterborne inferred from XGC series)
- thinner type and % — not published anywhere
- hardener: none stated (assumed 1K)
- solids %
- viscosity
- density
- drying times (dust-free / touch / sand / full)
- pot life
- hardness / chemical resistance / elasticity / lightfastness values
- shelf life, packaging
- not listed at t-colormarket.ru (search XGC072 returns nothing) nor at woodonline/lakokraska31/ndom31
- not in 2025-26 catalog transcripts or exterior leaflet
- not used in any official finishing schedule
- no TDS PDF found (web search budget exhausted; curl searches found nothing)
- no web search possible in verification pass (search budget exhausted); Milesi XGC072 TDS still unsearched