HTL90020
HTL90020 waterborne parquet lacquer, 20 gloss
One-component waterborne clear acrylic parquet lacquer, matt 20 gloss. Hard and abrasion-resistant, odourless, non-yellowing, resists household products. NMP-free. Ready to use — just stir.
- Parquet and stairs in any wood species
- Floorboards, solid wood, veneer, hardboard, chipboard, plywood in high-wear areas
- Humid rooms, kitchens, kids' rooms
Mix calculator
Ratio 100 : 2.5
| Component | Weigh out |
|---|---|
| HTL90020part A | 488 g |
| WATERThinner | 12.2 g |
| Total | 500 g |
Covers roughly 4.55 m² at 110 g/m².
Pot life of the mix: n/a (1K).
Ask about HTL90020
Answers are based on the HTL90020 data and the products it mixes with.
Mixing matrix
- WATERThinner% by weight: 0–5 %official% by volume: 0–5 %official
Only to trim spray viscosity; default is unthinned.
Dealer: do not exceed 5 % thinning.
| Role | Material | % by weight | % by volume | When |
|---|---|---|---|---|
| Thinner | WATER | 0–5 %official | 0–5 %official | Only to trim spray viscosity; default is unthinned.Dealer: do not exceed 5 % thinning. |
Percentages are per 100 parts of component A.
Characteristics
- Solids
- 31–34 (from HTL90 M)recommended
- Viscosity
- 30 ± 5 sdealer
- Gloss
- 20 ± 3 GUdealer
- Pot life
- n/a (1K)recommended
- Drying · Touch-dry
- 30dealer
- Drying · Full cure
- 8dealer
- Drying · Sand or stack
- 3–4recommended
- Drying · Light traffic (h)
- 24recommended
- Drying · Conditions
- 20 °C
- Hardness
- highofficial
- Abrasion resistance
- highofficial
- Lightfastness
- excellent yellowing resistanceofficial
- Chemical resistance
- household productsofficial
Application
HVLP
- Nozzle
- 1.3–1.5 mmrecommended
- Pressure · air
- 1.5–2 barrecommended
- Spray viscosity
- 25–35 s VZ-4 (DIN4)recommended
- Consumption
- 100–120 g/m²official
- Wet film
- 95–120 µmrecommended
- Coats
- 2–3 coatsrecommended
- Flash-off
- 10–20 minrecommended
- Recoat
- 2–4 hrecommended
- Sanding between coats
- P240–P320 (screen/abrasive pad on floors)recommended
Use a gun and hoses rated for waterborne (stainless); flush with water before and after. Never thin more than 5 % water.
Conventional spray
- Nozzle
- 1.4–1.6 mmrecommended
- Pressure · air
- 2.5–3.5 barrecommended
- Consumption
- 100–120 g/m²official
Air spray is the manufacturer's listed method (orange icon in the catalog).
Airmix (air-assisted airless)
- Nozzle
- 0.23–0.28 mmrecommended
- Pressure · fluid
- 20–60 barrecommended
- Pressure · air
- 1–2 barofficial
For production flat parts only (boards, treads before installation).
Roller
- Consumption
- 100–120 g/m²recommended
- Coats
- 2–3 coatsrecommended
Catalog: can be applied to an installed floor — on site use a short-nap microfibre/velour roller, brush for edges and corners.
Brush
- Consumption
- 90–120 g/m²recommended
Synthetic brush for waterborne; lay off along the grain, don't overwork.
Process and compatibility
- Substrate preparation
- Sand the floor, finish at P120–P150 (P180 on veneer), remove all dust. Wood must be dry and free of oil, wax and silicone.recommended
- Sanding
- Denib P240–P320 between coats; do not sand the final coatrecommended
- Temperature and humidity
- Apply above 15 °C and below 70 % RH.dealer
- Don'ts
- Don't thin more than 5 % (water only).
- Don't mix with solvents or solvent-borne coatings.
- Don't apply below 15 °C or above 70 % RH.
- Don't sand or polish the final coat.
Storage
- Storage temperature
- +5…+30 °C, protect from frostrecommended
- Packaging
- 1, 5, 10 kgdealer
Safety: Odourless, solvent-free, NMP-free; suitable for kids' rooms and kitchens (dealer). When spraying wear an aerosol respirator and ventilate. Clean up with water.
Sources
Value tags: “official”, “dealer”, “catalog”, “schedule” are Technocolor data; “workshop” is from our own datasheets; “recommended” is our engineering estimate (hover to see the reasoning).
- official page: properties, spray 100–120 g/m², water 0–5 % w/w and v/v
- dealer: gloss 20 ± 3, viscosity 30 ± 5 s VZ-4, touch 30 min, full 8 h, >15 °C/<70 % RH, ≤5 % thinning, packs 1/5/10 kg, uses
- official methods page (airmix air 1–2 bar, efficiency notes)
- official characteristics vocabulary
Not covered by the sources
- solids % for HTL90020 itself (only HTL90 M values: 31 % catalog / 34 ± 1 % dealer)
- density
- dust-free time
- sand/stack time
- hardness value (pendulum/Persoz)
- abrasion value (Taber)
- elasticity
- shelf life
- storage temperature (official)
- compatible primer/sealer
- optional crosslinker (none listed)
- no Technocolor finishing schedule uses HTL90020
- no TDS PDF found