HTL90 M
HTL90 M waterborne parquet lacquer, 20 gloss
Highly transparent, abrasion- and chemical-resistant, levels very well on flat surfaces. Solvent-free, so it can be applied to an installed floor. Brush, roller or air spray.
- Parquet and stairs in any wood species
- Can be applied to an installed floor (solvent-free)
Mix calculator
Ratio 100 : 2.5
| Component | Weigh out |
|---|---|
| HTL90 Mpart A | 488 g |
| WATERThinner | 12.2 g |
| Total | 500 g |
Covers roughly 4.76 m² at 105 g/m².
Pot life of the mix: n/a (1K).
Ask about HTL90 M
Answers are based on the HTL90 M data and the products it mixes with.
Mixing matrix
- WATERThinner% by weight: 0–5 %dealer% by volume: 0–5 %dealer
Only if needed.
Max 5 %.
| Role | Material | % by weight | % by volume | When |
|---|---|---|---|---|
| Thinner | WATER | 0–5 %dealer | 0–5 %dealer | Only if needed.Max 5 %. |
Percentages are per 100 parts of component A.
Characteristics
- Viscosity
- 30 ± 5 sdealer
- Pot life
- n/a (1K)recommended
- Drying · Touch-dry
- 30dealer
- Drying · Full cure
- 8dealer
- Drying · Sand or stack
- 3–4recommended
- Drying · Conditions
- 20 °C
- Hardness
- highdealer
- Lightfastness
- excellent yellowing resistancedealer
- Chemical resistance
- chemicals/household productscatalog
Application
HVLP
- Nozzle
- 1.3–1.5 mmrecommended
- Pressure · air
- 1.5–2 barrecommended
- Spray viscosity
- 25–35 s VZ-4 (DIN4)recommended
- Consumption
- 90–120 g/m²dealer
- Wet film
- 85–120 µmrecommended
- Coats
- 2–3 coatsrecommended
- Flash-off
- 10–20 minrecommended
- Recoat
- 2–4 hrecommended
- Sanding between coats
- P240–P320 (screen/abrasive pad on floors)recommended
Use a gun and hoses rated for waterborne (stainless); flush with water before and after. Never thin more than 5 % water.
Conventional spray
- Nozzle
- 1.4–1.6 mmrecommended
- Pressure · air
- 2.5–3.5 barrecommended
- Consumption
- 90–120 g/m²catalog
Air spray is the manufacturer's listed method (orange icon in the catalog).
Airmix (air-assisted airless)
- Nozzle
- 0.23–0.28 mmrecommended
- Pressure · fluid
- 20–60 barrecommended
- Pressure · air
- 1–2 barofficial
For production flat parts only (boards, treads before installation).
Roller
- Consumption
- 90–120 g/m²recommended
- Coats
- 2–3 coatsrecommended
- Why this method
- Roller is listed as a method in the catalog text ('кистью, валиком и пневматическим распылением'); the consumption figure is derived.
Catalog: can be applied to an installed floor — on site use a short-nap microfibre/velour roller, brush for edges and corners.
Brush
- Consumption
- 90–120 g/m²catalog
Synthetic brush for waterborne; lay off along the grain, don't overwork.
Process and compatibility
- Substrate preparation
- Sand the floor, finish at P120–P150 (P180 on veneer), remove all dust. Wood must be dry and free of oil, wax and silicone.recommended
- Sanding
- Denib P240–P320 between coats; do not sand the final coatrecommended
- Temperature and humidity
- Apply above 15 °C and below 70 % RH.dealer
- Don'ts
- Don't thin more than 5 % (water only).
- Don't mix with solvents or solvent-borne coatings.
- Don't apply below 15 °C or above 70 % RH.
- Don't sand or polish the final coat.
Storage
- Storage temperature
- +5…+30 °C, protect from frostrecommended
- Packaging
- 1, 5, 10 kgdealer
Safety: Solvent-free (catalog) and NMP-free (dealer). When spraying wear an aerosol respirator and ventilate. Clean up with water.
Sources
Value tags: “official”, “dealer”, “catalog”, “schedule” are Technocolor data; “workshop” is from our own datasheets; “recommended” is our engineering estimate (hover to see the reasoning).
Not covered by the sources
- official page
- density
- dust-free time
- sand time
- hardness/abrasion values
- shelf life
- gloss conflict (catalog 20 vs dealer 30 ± 3)
- solids conflict (31 vs 34 ± 1 %)
- primer
- no TDS