HTL20 G
HTL20 G waterborne self-sealing lacquer, gloss
One-pack waterborne gloss self-sealing clear: very clear, non-yellowing, abrasion resistant, fast drying, no solvent smell. Ready to use; self-sealing. Brush, roller or spray.
- Interior furniture and decor
- Doors, trims, wall and slatted panels, handrails, lining boards
- Kitchens, bathrooms, kids' rooms (solvent-free)
- Refinishing previously coated surfaces
Mix calculator
Ratio 100 : 0.0
| Component | Weigh out |
|---|---|
| HTL20 Gpart A | 500 g |
| Water (demineralised)Thinner | 0.0 g |
| Total | 500 g |
Covers roughly 4.76 m² at 105 g/m².
Pot life of the mix: n/a (1K).
Ask about HTL20 G
Answers are based on the HTL20 G data and the products it mixes with.
Mixing matrix
- Water (demineralised)Thinner% by weight: 0–10 %catalog% by volume: 0–10 %recommended
Usually not needed — 27 s is already spray viscosity.
Demineralised water only.
| Role | Material | % by weight | % by volume | When |
|---|---|---|---|---|
| Thinner | Water (demineralised) | 0–10 %catalog | 0–10 %recommended | Usually not needed — 27 s is already spray viscosity.Demineralised water only. |
Percentages are per 100 parts of component A.
Characteristics
- Solids
- 32 %catalog
- Viscosity
- 27 ± 5 sdealer
- Density
- ≈1.03 g/cm³recommended
- Gloss
- 80 ± 3 GUdealer
- Pot life
- n/a (1K)recommended
- Drying · Touch-dry
- 30 mindealer
- Drying · Sand or stack
- 4 hdealer
- Drying · Full cure
- 8 hdealer
- Drying · Conditions
- 20 °C
- Lightfastness
- excellent non-yellowingdealer
- Chemical resistance
- high abrasion resistance, washable, suits humid rooms (qualitative)dealer
- Thixotropy
- norecommended
Colours
- HTL20 G · clear
Application
HVLP
- Nozzle
- 1.4–1.5 mmrecommended
- Pressure · fluid
- gravity cup / 0.8–1.2 bar if pressure potrecommended
- Pressure · air
- 1.8–2.2 barrecommended
- Spray viscosity
- 27 ± 5 sdealer
- Target spray viscosity
- as supplied (27 ± 5 s)recommended
- Consumption · Primer coat
- 100 g/m²dealer
- Consumption · Topcoat
- 120 g/m²dealer
- Consumption · Product family
- 90–120 g/m²catalog
- Wet film
- 85–120 µmrecommended
- Coats
- 2–3 coats; dealer schedule: 1× as primer 100 g/m² + 1× topcoat 120 g/m²dealer
- Flash-off
- 10–20 minrecommended
- Gun distance
- 15–20 cmrecommended
- Overlap
- 50–75 %recommended
Lay it on as an even wet coat, don't dust it — dry-sprayed waterborne goes orange-peel and cloudy. Don't overload: 120 g/m² per pass max. Stainless gear, flush with water before and after.
Conventional spray
- Nozzle
- 1.4–1.6 mmrecommended
- Pressure · air
- 2.5–3.5 barrecommended
- Consumption · Primer coat
- 100 g/m²dealer
- Consumption · Topcoat
- 120 g/m²dealer
- Consumption · Product family
- 90–120 g/m²catalog
Official method is plain air spray. Transfer efficiency up to ~40 % (methods page).
Airmix (air-assisted airless)
- Nozzle
- 0.23–0.28 mmrecommended
- Pressure · fluid
- 20–40 barrecommended
- Pressure · air
- 1–2 barofficial
- Consumption · Primer coat
- 100 g/m²dealer
- Consumption · Topcoat
- 120 g/m²dealer
- Consumption · Product family
- 90–120 g/m²catalog
Pump and hoses must be waterborne-rated (stainless).
Brush
- Consumption
- 90–120 g/m²catalog
Synthetic brush, lay off in one direction, don't overwork — it skins fast.
Roller
- Consumption
- 90–120 g/m²recommended
Short-nap velour/microfibre roller; roller marks show in gloss — spray fronts.
Process and compatibility
- Substrate preparation
- Sanded clean wood/veneer/MDF, dust off. Stain with CPH series, dry 2–4 h before the first coat.source
- Goes over
- bare wood (self-sealing) / CPH stains
- Sanding · Between coats
- P240–P280 after 4 hdealer
- Sanding · Final
- do not sand the final coatrecommended
- Temperature and humidity
- > 15 °C, RH < 70 %dealer
- Ideal temperature and RH
- 18–25 °C, RH 50–65 %, good air movementrecommended
- Don'ts
- Don't apply below 15 °C or above 70 % RH.
- Don't thin more than 10 % or with hard water.
- Don't mix with solvent thinners (S50/S80 etc.) or with 2K acrylic/PU.
- Don't flood a thick coat in one pass.
- Don't let the can freeze.
Storage
- Storage temperature
- 5–30 °Crecommended
- Packaging
- 1 kg,5 kg,10 kgdealer
Safety: Solvent-free, odourless — can be used on children's furniture (2025-26 catalog); dealer: kitchens, bathrooms, kids' rooms. When spraying wear a particulate mask (P2) and ventilate.
Sources
Value tags: “official”, “dealer”, “catalog”, “schedule” are Technocolor data; “workshop” is from our own datasheets; “recommended” is our engineering estimate (hover to see the reasoning).
- dealer: gloss 80±3, visc 27±5 s VZ-4, touch 30 min, full 8 h, schedule CPH→HTL20 G 100 g/m²→4 h→P240–P280→HTL20 G 120 g/m²→8 h
- methods page
Not covered by the sources
- no official t-color.ru page (404 for htl20-g slug)
- gloss 60 (catalog) vs 80±3 (dealer) unresolved
- solids measured value for G alone (only family 32 %)
- official water % by volume
- density
- dust-free time
- hardness / elasticity
- shelf life
- no Technocolor TDS PDF found